Husqvarna 532 44 05-66, 96045003000 To Level Mower, Turn nut right Turn nut left To raise mower

Page 21

SERVICE AND ADJUSTMENTS

TO LEVEL MOWER

Make sure tires are properly inflated to the PSI shown on tires. If tires are over or under inflated, it may affect the appearance of your lawn and lead you to think the mower is not adjusted properly.

VISUAL SIDE-TO-SIDE ADJUSTMENT (See Fig. 32)

•Withalltiresproperlyinflatedandifyourlawnappearsun- evenlycut,determinewhichsideofmoweriscuttinglower.

NOTE: As desired, you can raise the low side of mower or lower the high side.

•Go to side of mower you wish to adjust.

•With a 3/4" or adjustable wrench, turn lift link adjust- ment nut (A) to the left to lower the mower, or, to the right to raise the mower.

 

A

Turn nut right

Turn nut left

to raise mower

to lower mower

 

Fig. 32

NOTE: Each full turn of adjustment nut will change mower height about 3/16".

•Test your adjustment by mowing some uncut grass and visually checking the appearance. Readjust, if necessary, until you are satisfied with the results.

PRECISION SIDE-TO-SIDE ADJUSTMENT (See Fig. 33)

•With all tires properly inflated, park tractor on level ground or driveway.

CAUTION: Blades are sharp. Protect your hands with gloves and/or wrap blade with heavy cloth.

•Raise mower to its highest position.

•At both sides of mower, position blade at side and measure the distance (A) from bottom edge of blade to the ground. The distance should be the same on both sides.

 

02966

A

A

Fig. 33

21

•If adjustment is necessary, see steps in Visual Adjust- ment instructions above.

•Recheck measurements, adjust if necessary until both sides are equal.

FRONT-TO-BACK ADJUSTMENT (See Figs. 34 and 35) IMPORTANT: Deck must be level side-to-side.

To obtain the best cutting results, the mower blades should be adjusted so the front tip is 1/8" to 1/2" lower than the rear tip when the mower is in its highest position.

CAUTION: Blades are sharp. Protect your hands with gloves and/or wrap blade with heavy cloth.

•Raise mower to highest position.

•Position any blade so the tip is pointing straight forward. Measure distance (B) to the ground at front and rear tip of the blade.

•If front tip of blade is not 1/8" to 1/2" lower than the rear tip, go to the front of tractor.

•With an 11/16" or adjustable wrench, loosen jam nut A several turns to clear adjustment nut B.

•With a 3/4" or adjustable wrench, turn front link adjust- ment nut (B) clockwise (ltighten) to raise the front of mower, or, counterclockwise (loosen) to lower the front mower.

 

02548

B

B

Fig. 34

 

B

 

 

A

Tighten adjust

Loosen adjust

nut B to raise

nut B to lower

mower

mower

02950

 

Loosen jam nut A first

 

Fig. 35

 

NOTE: Each full turn of the adjustment nut will change mower height about 1/8".

•Recheck measurements, adjust if necessary until front tip of blade is 1/8" to 1/2" lower than the rear tip.

•Hold adjustment nut in position with wrench and tighten jam nut securely against adjustment nut.

Page 20 Page 22
Image 21
Page 20 Page 22
Contents YTH2348 Safe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationGeneral Service ServiceIII. Children IV. TowingTable of Contents Tools Required for Assembly AssemblyUnassembled Parts ToremovetractorfromcartonCheck Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Reverse Operation System ROS on Position Know Your TractorHOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Adjust Mower Cutting Height See FigSystem Characteristics To Operate MowerUsing the Reverse Operation System Service REMINDER/HOUR MeterReverse Operation System ROS To Transport See FigsCheck Engine OIL Level Before Starting the EngineADD Gasoline To Start Engine See FigPurge Transmission Mowing TipsMaintenance MaintenanceGeneral Recommendations ScheduleTractor BatteryBrake Operation TiresEngine Cleaning IN-LINE Fuel Filter See FigDeck Washout Port See Fig Service and Adjustments To Install Mower See FigsTo Remove Mower See Fig Turn Steering Wheel Left and Position Mower See Fig ANTI-SWAY BAR SAttach Mower Side Suspension Arms a to Chassis See Fig Turn nut right Turn nut left To raise mower To Level MowerTo Replace Mower Blade Drive Belt See Fig Mower Drive Belt InstallationTo Replace Motion Drive Belt See Fig Mower Drive Belt RemovalWeak or Dead Fully Charged Battery To Start Engine with a Weak Battery See FigTo Check Brake Front Wheel TOE-IN/CAMBERTo Adjust Throttle Control Cable REMOVAL/REPLACEMENTTo Adjust Choke Control To Adjust CarburetorOther StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsEngine continues Decals Wheels and TiresKEY Part Description SCH12 SchematicElectrical Socket Asm. Bulb Twistlock 208 Chassis 196 DriveBolt Rdhd Sqnk 3/8-16 x 2-3/4 Gr Engine Spark Arrester KITKEY Part NO. NO. Description Engine Power Rating InformationSteering Assembly Seat Assembly Mower Deck KEY Part NO. NO. Description Mower Lift Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationLimitations and Exclusions HOW to Obtain Service Consumer Wheeled Warranty Chart Front Mounted Deck Riders Engine Transmission 11.05.10 JA

532 44 05-66, 96045003000 specifications

The Husqvarna 96045003000,532 44 05-66 is a powerful and innovative riding mower designed for residential lawn care. This model stands out due to its combination of performance, durability, and user-friendly features, making it a popular choice among homeowners seeking an efficient mowing solution.

At the heart of the Husqvarna 96045003000 is its robust engine. It is equipped with a premium quality engine that offers reliable performance and excellent fuel efficiency. The powerful motor enables the mower to tackle even the toughest grass, ensuring a pristine finish to your lawn with every cut. Along with this efficiency, the mower is also designed to minimize emissions, promoting a more environmentally friendly operation.

A standout feature of this model is its advanced cutting deck technology. The 42-inch cutting deck size allows for a wide cutting path, reducing the number of passes needed to cover larger areas. The design of the cutting deck ensures even grass distribution and enhanced mulching capabilities, allowing users to finely chop grass clippings for better nutrient return to the soil.

Equipped with the latest in ergonomic design, the Husqvarna 96045003000 prioritizes user comfort. It features an adjustable seat that ensures a comfortable riding position for various user heights and preferences. The steering system provides precise control, making it easy to navigate around obstacles in your yard.

The mowing height can easily be adjusted to suit different grass types and conditions, providing versatility for varying lawn care needs. This adaptability allows homeowners to maintain their lawns at desired lengths for aesthetic appeal and health.

Additionally, Husqvarna incorporates advanced safety features into this model. The cutting blade automatically disengages when the operator leaves the seat, minimizing the risk of accidents. The mower also comes with easy-to-access controls to ensure that all functions are within reach, enhancing operational safety.

In conclusion, the Husqvarna 96045003000,532 44 05-66 offers an excellent balance of power, efficiency, and safety features. Its durable construction and advanced technology make it an essential tool for any homeowner looking to maintain a beautiful lawn with ease.
Top Page Image Contents