Husqvarna 917.28961 To Adjust Mower Cutting Height See Fig, To Adjust Gauge Wheels See Fig

Page 10

OPERATION

TO ADJUST MOWER CUTTING HEIGHT (See Fig. 8)

The position of the attachment lift lever (A) determines the cutting height.

A

Fig. 8

•Put attachment lift lever in desired cutting height slot.

The cutting height range is approximately 1" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

•The average lawn should be cut to approximately 2-1/2" during the cool season and to over 3" during hot months. For healthier and better looking lawns, mow often and after moderate growth.

•For best cutting performance, grass over 6" in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS (See Fig. 9)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE:Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in the Operation section of this manual).

•With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole as shown and tighten securely.

•Repeat for opposite side installing gauge wheel in same adjustment hole.

Fig. 9

10

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitat- ing or cutting off when operating your equipment on rough, rolling terrain or hills.

•Select desired height of cut (see "TO ADJUST MOWER CUTTING HEIGHT")

•Start mower blades by engaging attachment clutch control.

TO STOP MOWER BLADES

Disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector shield

(S) in place (See Fig. 10).

S

Fig. 10

TO TRANSPORT (See Figs. 11)

When pushing or towing your tractor, be sure to disengage transmission by placing freewheel control in freewheeling position. Free wheel control is located at the rear of tractor.

•Raise attachment lift to highest position with attachment lift control.

•Pull freewheel control out and into the slot and release so it is held in the disengaged position.

•Do not push or tow tractor at more than two (2) MPH.

•To reengage transmission, reverse above procedure.

TRANSMISSION ENGAGED

TRANSMISSION DISENGAGED

Fig. 11

NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.).

Page 9 Page 11
Image 10
Page 9 Page 11
Contents 917.289610 General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIV. Towing III. ChildrenSafe Handling of Gasoline Table of Contents Unassembled Parts AssemblyTools Required for Assembly ToremovetractorfromcartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor Stopping See Fig HOW to USE Your TractorTo SET Parking Brake See Fig To USE Throttle Control D See FigTo Operate Mower To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Stop Mower BladesBefore Starting the Engine Mowing Tips Purge TransmissionGeneral Recommendations MaintenanceMaintenance ScheduleBlade Care BatteryTractor Blade Removal See FigEngine IN-LINE Fuel Filter See Fig CleaningDeck Washout Port See Fig To Install Mower See Service and AdjustmentsTo Remove Mower See Fig Install belt on engine pulley M, in belt keepers G To Level Mower To Check Brake To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt See Fig To Remove Wheel See Fig Transaxle Motion Control Lever Neutral Adjustment See FigTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTransmission Fuel System StorageOther Engine OILTroubleshooting Fires when turn To run when operBattery will not Engine continuesDecals Wheels and TiresSchematic Optional Twin CYL. EnginesElectrical Tractor - Model Number YTH2042 Chassis Tractor - Model Number YTH2042 Drive Tractor - Model Number YTH2042 Engine Engine Power Rating Information Steering Assembly Tractor - Model Number YTH2042 Mower Deck 532 40 Mower Housing Mower Lift 532 19 51-81 Link Asm Lift LH RearSeat Assembly 532 42 SeatModel K46BA KEY Part Description Briggs Engine Model Number 331777, Type Number 1372-B1 Liquid Gasket and the Breather Gasket are InterchangeableBriggs Engine Model Number 331777, Type Number 1372-B1 118 125 141 108 131 634 130 217 633 987 KEY Part Description Seal-Valve Service Notes Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX05.04.10 BAD

917.28961 specifications

The Husqvarna 917.28961 is a premium riding mower designed for homeowners seeking exceptional performance and maneuverability in maintaining their lawns. Equipped with a powerful engine and innovative features, the 917.28961 ensures efficient cutting and pleasant operation, making it a popular choice among gardening enthusiasts.

At the heart of the Husqvarna 917.28961 is a reliable and robust engine that delivers ample power for tackling various terrains and grass types. With a 24 HP Briggs & Stratton engine, this riding mower has the horsepower necessary for smooth operation, even on challenging inclines. The engine is designed for optimal fuel efficiency, reducing overall running costs while maximizing mowing efficiency.

One of the standout features of the Husqvarna 917.28961 is its 54 inch reinforced cutting deck. This wide cutting deck allows for faster mowing, reducing the number of passes needed to achieve a well-manicured lawn. The deck also features a direct rear discharge system that enhances grass clipping dispersal, promoting a healthier lawn by avoiding clumping.

Maneuverability is crucial for maintaining the aesthetic appeal of lawns with obstacles and tight spaces. The 917.28961 is designed with a tight turning radius, enabling users to navigate easily around flowerbeds and trees, ensuring every inch of the yard receives care. Additionally, the mower's adjustable cutting height allows users to choose the perfect length for their grass, accommodating different seasons and growth patterns.

Another significant characteristic of the Husqvarna 917.28961 is its user-friendly controls and dashboard. The mower is equipped with an ergonomically designed seat, ensuring comfort during extended mowing sessions. The intuitive controls make it easy for anyone to operate, whether they are seasoned lawn care veterans or inexperienced beginners.

The Husqvarna 917.28961 also integrates advanced safety features such as an automatic blade brake that engages instantly when the operator leaves the seat. This feature ensures that the mower comes to a complete stop, reducing the risk of accidents.

In summary, the Husqvarna 917.28961 combines power, efficiency, and user comfort into a single mowing solution. With its impressive engine, wide cutting deck, and easy maneuverability, this riding mower is well-suited for homeowners aiming for a pristine lawn without the hassle of traditional mowing methods. Whether maintaining small or large yards, the Husqvarna 917.28961 is a reliable partner for lawn care.
Top Page Image Contents