Husqvarna 917.28961 owner manual Mowing Tips, Purge Transmission

Page 12

OPERATION

Insert key into ignition and turn key clockwise to “START” position and release key as soon as engine starts. Do not run starter continuously for more than fifteen seconds per minute. If the engine does not start after several attempts, move throttle control to fast position, wait a few minutes and try again. If engine still does not start, move the throttle control back to the choke position and retry.

WARM WEATHER STARTING (50° F/10°C and above)

When engine starts, move the throttle control to the fast position.

The attachments and ground drive can now be used. If the engine does not accept the load, restart the engine and allow it to warm up for one minute using the choke as described above.

COLD WEATHER STARTING (50° F/10°C and below)

When engine starts, allow engine to run with the throttle control in the choke position until the engine runs roughly, then move throttle control to fast position. This may require an engine warm-up period from several seconds to several minutes, depending on the temperature.

AUTOMATIC TRANSMISSION WARM UP

Before driving the unit in cold weather, the transmission should be warmed up as follows:

Be sure the tractor is on level ground.

Place the motion control lever in neutral. Release the parking brake and let the clutch/brake slowly return to operating position.

Allow one minute for transmission to warm up. This can be done during the engine warm up period.

Theattachmentscanalsobeusedduringtheenginewarm- up period after the transmission has been warmed up.

NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32° F) the carburetor fuel mixture may need to be adjusted for best engine performance. See “TO ADJUST CARBURETOR” in the Service and Adjustments section of this manual.

PURGE TRANSMISSION

CAUTION: Never engage or disengage freewheelleverwhiletheengineisrunning.

To ensure proper operation and performance, it is recom- mended that the transmission be purged before operating tractor for the first time. This procedure will remove any trapped air inside the transmission which may have devel- oped during shipping of your tractor.

IMPORTANT: SHOULD YOUR TRANSMISSION REQUIRE REMOVAL FOR SERVICE OR REPLACEMENT, IT SHOULD BE PURGED AFTER REINSTALLATION BEFORE OPERATING THE TRACTOR.

1.Place tractor safely on a level surface - that is clear and open - with engine off and parking brake set.

2.Disengage transmission by placing freewheel control in freewheeling position (See “TO TRANSPORT” in this section of manual).

3.Sitting in the tractor seat, start engine. After the engine is running, move throttle control to slow position. With motion control lever in neutral position, slowly disengage clutch/brake pedal.

12

CAUTION: At any time, during step 4, there may be movement of the drive wheels.

4.Move motion control lever to full forward position and hold for five (5) seconds. Move lever to full reverse position and hold for five (5) seconds. Repeat this procedure three (3) times.

5.Move motion control lever to neutral position. Shut- off engine and set parking brake.

6.Engage transmission by placing freewheel control in engaged position (See “TO TRANSPORT” in this sec- tion of manual).

7.Sitting in the tractor seat, start engine. After the engine is running, move throttle control to half (1/2) speed. With motion control lever in neutral position, slowly disengage clutch/brake pedal.

8.Slowly move motion control lever forward, after the tractor moves approximately five (5) feet, slowly move motion control lever to reverse position. After the trac- tor moves approximately five (5) feet return the motion control lever to the neutral position. Repeat this proce- dure with the motion control lever three (3) times.

Your transmission is now purged and now ready for normal operation.

MOWING TIPS

Tire chains cannot be used when the mower housing is attached to tractor.

Mower should be properly leveled for best mowing performance. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual.

The left hand side of mower should be used for trimming.

Drive so that clippings are discharged onto the area that has been cut. Have the cut area to the right of the tractor. This will result in a more even distribution of clippings and more uniform cutting.

When mowing large areas, start by turning to the right so that clippings will discharge away from shrubs, fences, driveways, etc. After one or two rounds, mow in the opposite direction making left hand turns until finished (See Fig. 13).

Fig. 13

Ifgrassisextremelytall,itshouldbemowedtwicetoreduce load and possible fire hazard from dried clippings. Make first cut relatively high; the second to the desired height.

Do not mow grass when it is wet. Wet grass will plug mower and leave undesirable clumps. Allow grass to dry before mowing.

Always operate engine at full throttle when mow- ing to assure better mowing performance and proper discharge of material. Regulate ground speed by selecting a low enough gear to give the mower cutting performance as well as the quality of cut desired.

When operating attachments, select a ground speed that will suit the terrain and give best performance of the attachment being used.

Image 12
Contents 917.289610 Safety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationIII. Children IV. TowingSafe Handling of Gasoline Table of Contents Assembly Tools Required for AssemblyUnassembled Parts ToremovetractorfromcartonCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To SET Parking Brake See FigStopping See Fig To USE Throttle Control D See FigTo Adjust Mower Cutting Height See Fig To Adjust Gauge Wheels See FigTo Operate Mower To Stop Mower BladesBefore Starting the Engine Mowing Tips Purge TransmissionMaintenance MaintenanceGeneral Recommendations ScheduleBattery TractorBlade Care Blade Removal See FigEngine Cleaning IN-LINE Fuel Filter See FigDeck Washout Port See Fig Service and Adjustments To Install Mower SeeTo Remove Mower See Fig Install belt on engine pulley M, in belt keepers G To Level Mower To Replace Mower Blade Drive Belt See Fig To Check BrakeTo Replace Motion Drive Belt See Fig Transaxle Motion Control Lever Neutral Adjustment See Fig To Start Engine with a Weak Battery See FigTo Remove Wheel See Fig Front Wheel TOE-IN/CAMBERTransmission Storage OtherFuel System Engine OILTroubleshooting To run when oper Battery will notFires when turn Engine continuesDecals Wheels and TiresSchematic Optional Twin CYL. EnginesElectrical Tractor - Model Number YTH2042 Chassis Tractor - Model Number YTH2042 Drive Tractor - Model Number YTH2042 Engine Engine Power Rating Information Steering Assembly Tractor - Model Number YTH2042 Mower Deck 532 40 Mower Housing Mower Lift 532 19 51-81 Link Asm Lift LH RearSeat Assembly 532 42 SeatModel K46BA KEY Part Description Briggs Engine Model Number 331777, Type Number 1372-B1 Liquid Gasket and the Breather Gasket are InterchangeableBriggs Engine Model Number 331777, Type Number 1372-B1 118 125 141 108 131 634 130 217 633 987 KEY Part Description Seal-Valve Service Notes Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX05.04.10 BAD

917.28961 specifications

The Husqvarna 917.28961 is a premium riding mower designed for homeowners seeking exceptional performance and maneuverability in maintaining their lawns. Equipped with a powerful engine and innovative features, the 917.28961 ensures efficient cutting and pleasant operation, making it a popular choice among gardening enthusiasts.

At the heart of the Husqvarna 917.28961 is a reliable and robust engine that delivers ample power for tackling various terrains and grass types. With a 24 HP Briggs & Stratton engine, this riding mower has the horsepower necessary for smooth operation, even on challenging inclines. The engine is designed for optimal fuel efficiency, reducing overall running costs while maximizing mowing efficiency.

One of the standout features of the Husqvarna 917.28961 is its 54 inch reinforced cutting deck. This wide cutting deck allows for faster mowing, reducing the number of passes needed to achieve a well-manicured lawn. The deck also features a direct rear discharge system that enhances grass clipping dispersal, promoting a healthier lawn by avoiding clumping.

Maneuverability is crucial for maintaining the aesthetic appeal of lawns with obstacles and tight spaces. The 917.28961 is designed with a tight turning radius, enabling users to navigate easily around flowerbeds and trees, ensuring every inch of the yard receives care. Additionally, the mower's adjustable cutting height allows users to choose the perfect length for their grass, accommodating different seasons and growth patterns.

Another significant characteristic of the Husqvarna 917.28961 is its user-friendly controls and dashboard. The mower is equipped with an ergonomically designed seat, ensuring comfort during extended mowing sessions. The intuitive controls make it easy for anyone to operate, whether they are seasoned lawn care veterans or inexperienced beginners.

The Husqvarna 917.28961 also integrates advanced safety features such as an automatic blade brake that engages instantly when the operator leaves the seat. This feature ensures that the mower comes to a complete stop, reducing the risk of accidents.

In summary, the Husqvarna 917.28961 combines power, efficiency, and user comfort into a single mowing solution. With its impressive engine, wide cutting deck, and easy maneuverability, this riding mower is well-suited for homeowners aiming for a pristine lawn without the hassle of traditional mowing methods. Whether maintaining small or large yards, the Husqvarna 917.28961 is a reliable partner for lawn care.