Husqvarna 917.28961 owner manual To Level Mower

Page 19

SERVICE AND ADJUSTMENTS

TO LEVEL MOWER

Make sure tires are properly inflated to the PSI shown on tires. If tires are over or under inflated, it may affect the appearance of your lawn and lead you to think the mower is not adjusted properly.

VISUAL SIDE-TO-SIDE ADJUSTMENT (See Fig. 27)

•With all tires properly inflated and if your lawn appears unevenly cut, determine which side of mower is cutting lower.

•With a 3/4" or adjustable wrench, turn lift link adjust- ment nut (A) to the left to lower LH side of mower, or, to the right to raise LH side of mower.

 

A

Turn nut right

Turn nut left

to raise mower

to lower mower

02948

 

Fig. 27

NOTE: Each full turn of adjustment nut will change mower height about 3/16".

•Test your adjustment by mowing some uncut grass and visually checking the appearance. Readjust, if necessary, until you are satisfied with the results.

PRECISION SIDE-TO-SIDE ADJUSTMENT (See Fig. 28)

•With all tires properly inflated, park tractor on level ground or driveway.

CAUTION: Blades are sharp. Protect your hands with gloves and/or wrap blade with heavy cloth.

•Raise mower to its highest position.

•At both sides of mower, position blade at side and measure the distance (A) from bottom edge of blade to the ground. The distance should be the same on both sides.

 

02966

A

A

Fig. 28

•If adjustment is necessary, see step in Visual Adjust- ment instructions above.

•Recheck measurements, adjust if necessary until both sides are equal.

FRONT-TO-BACK ADJUSTMENT (See Fig. 29 & 30) IMPORTANT: Deck must be level side-to-side.

To obtain the best cutting results, the mower blades should be adjusted so the front tip is 1/8" to 1/2" lower than the rear tip when the mower is in its highest position.

CAUTION: Blades are sharp. Protect your hands with gloves and/or wrap blade with heavy cloth.

•Raise mower to highest position.

•Position blade so the tip is pointing straight forward. Measure distance (B) to the ground at front and rear tip of the blade.

BB

Fig. 29

•If front tip of blade is not 1/8" to 1/2" lower than the rear tip, go to the front of tractor.

•With an 11/16" or adjustable wrench, loosen jam nut A several turns to clear adjustment nut B.

•With a 3/4" or adjustable wrench, turn front link adjust- ment nut (B) clockwise (tighten) to raise the front of mower, or, counterclockwise (loosen) to lower the front mower.

B

A

TIGHTEN ADJUST

LOOSEN

ADJUST NUT

NUT B TO RAISE

B TO LOWER

MOWER

 

02950

MOWER

 

LOOSEN JAM NUT A FIRST

 

Fig. 30

NOTE: Each full turn of the adjustment nut will change mower height about 1/8".

•Recheck measurements, adjust if necessary until front tip of blade is 1/8" to 1/2" lower than the rear tip.

•Hold adjustment nut in position with wrench and tighten jam nut securely against adjustment nut.

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents 917.289610 II. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIV. Towing III. ChildrenSafe Handling of Gasoline Table of Contents Toremovetractorfromcarton AssemblyTools Required for Assembly Unassembled PartsCheck Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor To USE Throttle Control D See Fig HOW to USE Your TractorTo SET Parking Brake See Fig Stopping See FigTo Stop Mower Blades To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Operate MowerBefore Starting the Engine Purge Transmission Mowing TipsSchedule MaintenanceMaintenance General RecommendationsBlade Removal See Fig BatteryTractor Blade CareEngine IN-LINE Fuel Filter See Fig CleaningDeck Washout Port See Fig To Install Mower See Service and AdjustmentsTo Remove Mower See Fig Install belt on engine pulley M, in belt keepers G To Level Mower To Check Brake To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt See Fig Front Wheel TOE-IN/CAMBER Transaxle Motion Control Lever Neutral Adjustment See FigTo Start Engine with a Weak Battery See Fig To Remove Wheel See FigTransmission Engine OIL StorageOther Fuel SystemTroubleshooting Engine continues To run when operBattery will not Fires when turnWheels and Tires DecalsOptional Twin CYL. Engines SchematicElectrical Tractor - Model Number YTH2042 Chassis Tractor - Model Number YTH2042 Drive Tractor - Model Number YTH2042 Engine Engine Power Rating Information Steering Assembly Tractor - Model Number YTH2042 Mower Deck 532 40 Mower Housing 532 19 51-81 Link Asm Lift LH Rear Mower Lift532 42 Seat Seat AssemblyModel K46BA KEY Part Description Liquid Gasket and the Breather Gasket are Interchangeable Briggs Engine Model Number 331777, Type Number 1372-B1Briggs Engine Model Number 331777, Type Number 1372-B1 118 125 141 108 131 634 130 217 633 987 KEY Part Description Seal-Valve Service Notes Service Notes Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation05.04.10 BAD

917.28961 specifications

The Husqvarna 917.28961 is a premium riding mower designed for homeowners seeking exceptional performance and maneuverability in maintaining their lawns. Equipped with a powerful engine and innovative features, the 917.28961 ensures efficient cutting and pleasant operation, making it a popular choice among gardening enthusiasts.

At the heart of the Husqvarna 917.28961 is a reliable and robust engine that delivers ample power for tackling various terrains and grass types. With a 24 HP Briggs & Stratton engine, this riding mower has the horsepower necessary for smooth operation, even on challenging inclines. The engine is designed for optimal fuel efficiency, reducing overall running costs while maximizing mowing efficiency.

One of the standout features of the Husqvarna 917.28961 is its 54 inch reinforced cutting deck. This wide cutting deck allows for faster mowing, reducing the number of passes needed to achieve a well-manicured lawn. The deck also features a direct rear discharge system that enhances grass clipping dispersal, promoting a healthier lawn by avoiding clumping.

Maneuverability is crucial for maintaining the aesthetic appeal of lawns with obstacles and tight spaces. The 917.28961 is designed with a tight turning radius, enabling users to navigate easily around flowerbeds and trees, ensuring every inch of the yard receives care. Additionally, the mower's adjustable cutting height allows users to choose the perfect length for their grass, accommodating different seasons and growth patterns.

Another significant characteristic of the Husqvarna 917.28961 is its user-friendly controls and dashboard. The mower is equipped with an ergonomically designed seat, ensuring comfort during extended mowing sessions. The intuitive controls make it easy for anyone to operate, whether they are seasoned lawn care veterans or inexperienced beginners.

The Husqvarna 917.28961 also integrates advanced safety features such as an automatic blade brake that engages instantly when the operator leaves the seat. This feature ensures that the mower comes to a complete stop, reducing the risk of accidents.

In summary, the Husqvarna 917.28961 combines power, efficiency, and user comfort into a single mowing solution. With its impressive engine, wide cutting deck, and easy maneuverability, this riding mower is well-suited for homeowners aiming for a pristine lawn without the hassle of traditional mowing methods. Whether maintaining small or large yards, the Husqvarna 917.28961 is a reliable partner for lawn care.
Top Page Image Contents