Husqvarna 917.28961 owner manual Transaxle Motion Control Lever Neutral Adjustment See Fig

Page 21

SERVICE AND ADJUSTMENTS

TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT (See Fig. 33)

The motion control lever has been preset at the factory and adjustment should not be necessary.

Loosen adjustment bolt in front of the right rear wheel, and lightly tighten.

Start engine and move motion control lever until tractor does not move forward or backward.

Hold motion control lever in that position and turn engine off.

While holding motion control lever in place, loosen the adjustment bolt.

Move motion control lever to the neutral (lock gate) position.

Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

After above adjustment is made, if the tractor still creeps forward or backward while motion control lever is in neutral position, follow these steps:

Loosen the adjustment bolt.

Move the motion control lever 1/4 to 1/2 inch in the direction it is trying to creep.

Tighten adjustment bolt securely.

Start engine and test.

If tractor still creeps, repeat above steps until satisfied.

MOTION CONTROL

NEUTRAL

LEVER

LOCK

 

GATE

 

ADJUSTMENT

 

BOLT

Fig. 33

TO REMOVE WHEEL (See Fig. 34)

Block up axle securely.

Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

Repair tire and reassemble.

On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

Replace washers and snap retaining ring securely in axle groove.

Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

RETAINING WASHERS

RING

AXLE

COVER

SQUARE KEY (REAR

WHEEL ONLY)

Fig. 34

FRONT WHEEL TOE-IN/CAMBER

Your new tractor front wheel toe-in and camber is set at the factory and is normal. The front wheel toe-in and camber are not adjustable. If damage has occurred to affect the factory set front wheel toe-in or camber, contact a qualified service center.

TO START ENGINE WITH A WEAK BATTERY (See Fig. 35)

WARNING: Lead-acid batteries generate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the MAINTENANCE sec- tion of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

BLACK cable first from chassis and then from the fully charged battery.

RED cable last from both batteries.

WEAK OR

FULLY CHARGED

DEAD BATTERY

BATTERY

Fig. 35

21

Image 21
Contents 917.289610 Safe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationIII. Children IV. TowingSafe Handling of Gasoline Table of Contents Tools Required for Assembly AssemblyUnassembled Parts ToremovetractorfromcartonCheck Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor To SET Parking Brake See Fig HOW to USE Your TractorStopping See Fig To USE Throttle Control D See FigTo Adjust Gauge Wheels See Fig To Adjust Mower Cutting Height See FigTo Operate Mower To Stop Mower BladesBefore Starting the Engine Purge Transmission Mowing TipsMaintenance MaintenanceGeneral Recommendations ScheduleTractor BatteryBlade Care Blade Removal See FigEngine Cleaning IN-LINE Fuel Filter See FigDeck Washout Port See Fig Service and Adjustments To Install Mower SeeTo Remove Mower See Fig Install belt on engine pulley M, in belt keepers G To Level Mower To Replace Mower Blade Drive Belt See Fig To Check BrakeTo Replace Motion Drive Belt See Fig To Start Engine with a Weak Battery See Fig Transaxle Motion Control Lever Neutral Adjustment See FigTo Remove Wheel See Fig Front Wheel TOE-IN/CAMBERTransmission Other StorageFuel System Engine OILTroubleshooting Battery will not To run when operFires when turn Engine continuesWheels and Tires DecalsOptional Twin CYL. Engines SchematicElectrical Tractor - Model Number YTH2042 Chassis Tractor - Model Number YTH2042 Drive Tractor - Model Number YTH2042 Engine Engine Power Rating Information Steering Assembly Tractor - Model Number YTH2042 Mower Deck 532 40 Mower Housing 532 19 51-81 Link Asm Lift LH Rear Mower Lift532 42 Seat Seat AssemblyModel K46BA KEY Part Description Liquid Gasket and the Breather Gasket are Interchangeable Briggs Engine Model Number 331777, Type Number 1372-B1Briggs Engine Model Number 331777, Type Number 1372-B1 118 125 141 108 131 634 130 217 633 987 KEY Part Description Seal-Valve Service Notes Service Notes Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation05.04.10 BAD

917.28961 specifications

The Husqvarna 917.28961 is a premium riding mower designed for homeowners seeking exceptional performance and maneuverability in maintaining their lawns. Equipped with a powerful engine and innovative features, the 917.28961 ensures efficient cutting and pleasant operation, making it a popular choice among gardening enthusiasts.

At the heart of the Husqvarna 917.28961 is a reliable and robust engine that delivers ample power for tackling various terrains and grass types. With a 24 HP Briggs & Stratton engine, this riding mower has the horsepower necessary for smooth operation, even on challenging inclines. The engine is designed for optimal fuel efficiency, reducing overall running costs while maximizing mowing efficiency.

One of the standout features of the Husqvarna 917.28961 is its 54 inch reinforced cutting deck. This wide cutting deck allows for faster mowing, reducing the number of passes needed to achieve a well-manicured lawn. The deck also features a direct rear discharge system that enhances grass clipping dispersal, promoting a healthier lawn by avoiding clumping.

Maneuverability is crucial for maintaining the aesthetic appeal of lawns with obstacles and tight spaces. The 917.28961 is designed with a tight turning radius, enabling users to navigate easily around flowerbeds and trees, ensuring every inch of the yard receives care. Additionally, the mower's adjustable cutting height allows users to choose the perfect length for their grass, accommodating different seasons and growth patterns.

Another significant characteristic of the Husqvarna 917.28961 is its user-friendly controls and dashboard. The mower is equipped with an ergonomically designed seat, ensuring comfort during extended mowing sessions. The intuitive controls make it easy for anyone to operate, whether they are seasoned lawn care veterans or inexperienced beginners.

The Husqvarna 917.28961 also integrates advanced safety features such as an automatic blade brake that engages instantly when the operator leaves the seat. This feature ensures that the mower comes to a complete stop, reducing the risk of accidents.

In summary, the Husqvarna 917.28961 combines power, efficiency, and user comfort into a single mowing solution. With its impressive engine, wide cutting deck, and easy maneuverability, this riding mower is well-suited for homeowners aiming for a pristine lawn without the hassle of traditional mowing methods. Whether maintaining small or large yards, the Husqvarna 917.28961 is a reliable partner for lawn care.