Husqvarna 96045002202 To Adjust Mower Cutting Height See Fig, To Adjust Gauge Wheels See Fig

Page 10

OPERATION

TO ADJUST MOWER CUTTING HEIGHT (See Fig. 8)

The position of the attachment lift lever (A) determines the cutting height.

A

Fig. 8

•Put attachment lift lever in desired cutting height slot.

The cutting height range is approximately 1" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

•The average lawn should be cut to approximately 2-1/2 " during the cool season and to over 3"during hot months. For healthier and better looking lawns, mow often and after moderate growth.

•For best cutting performance, grass over 6" in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS (See Fig. 9)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE: Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in this section of manual).

•With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole. Tighten securely.

•Repeat for all, installing gauge wheel in same adjust- ment hole.

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitat- ing or cutting off when operating your equipment on rough, rolling terrain or hills.

1.Select desired height of cut with attachment lift lever.

2.Start mower blades by engaging attachment clutch control.

TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector

shield (S) in place. (See Fig. 10)

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitat- ing or cutting off when operating your equipment on rough, rolling terrain or hills.

•Select desired height of cut (see "TO ADJUST MOWER CUTTING HEIGHT")

•Start mower blades by engaging attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector shield

(S) in place (See Fig. 10).

S

Fig. 9

Fig. 10

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents YTH2348 General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts AssemblyTools Required for Assembly To Remove Tractor from CartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor Throttle Control Used to control engine speedStopping See Fig HOW to USE Your TractorTo SET Parking Brake See Fig To USE Throttle Control D See FigTo Operate Mower To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig Shield S in place. See FigBefore Starting the Engine Automatic Transmission Warm UP To Start Engine See FigPurge Transmission RunningMowing Tips General Recommendations MaintenanceMaintenance ScheduleBlade Care BatteryTractor Blade Removal See FigEngine IN-LINE Fuel Filter See Fig CleaningDeck Washout Port See Fig To Remove Mower See Fig Service and AdjustmentsTo Install Mower and Drive Belt See Figs SET Parking Brake Lever and Lower AT- Tachment Lift See FigTurn Steering Wheel Left and Position Mower See Fig ANTI-SWAY BAR SSlide Mower Under Tractor See Fig Attach Rear Lift Links C See Fig Install Belt on Engine Clutch Pulley M SeeAttach Mower Side Suspension Arms a to Chassis See Fig Attach Front Link E See FigTo Level Mower Turn nut right Turn nut left To raise mowerTo Replace Mower Blade Drive Belt See Fig Mower Drive Belt InstallationMower Drive Belt Removal Front Wheel TOE-IN/CAMBER To Replace Motion Drive Belt See FigTo Check Brake To Remove Wheel for Repairs See FigWeak or Dead Fully Charged Battery To Start Engine with a Weak Battery See FigReplacing Battery See Fig To Replace Headlight BulbTo Adjust Choke Control To Remove Hood and Grill Assembly See FigTo Adjust Throttle Control Cable To Adjust CarburetorFuel System StorageOther Engine OILProblem Cause Correction Fires when turn To run when operBattery will not Engine continuesSchematic Tractor Model NO. YTH2348 96045002202, Product no 45Electrical KEY Part Description Chassis Chassis 204 532 41 Vent Top Hood197 Drive196 Tractor Model NO. YTH2348 96045002202, Product no 45 Engine Engine Power Rating Information KEY Part NO. NO. DescriptionSteering Assembly 532 41 Wheel, Steering 532 19 Mower Deck KEY Part NO. NO. Description Mower Lift Seat Assembly Decals Wheels and TiresSuggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXService Notes Service Notes Warranty Statement

532 43 65-03, 96045002202 specifications

The Husqvarna 532 43 65-03,96045002202 is a versatile and robust lawn mower blade designed to deliver exceptional cutting performance for a variety of mowing conditions. Known for its reliability and durability, this blade is an essential component for Husqvarna riding mowers and is a favored choice among homeowners and landscaping professionals.

One of the main features of the Husqvarna 532 43 65-03,96045002202 is its sharp cutting edge, made from high-quality steel designed to withstand the rigors of regular use. This blade is engineered to provide a clean and precise cut, promoting healthy grass growth and maintaining the aesthetic appeal of your lawn. Whether you're tackling thick grass, weeds, or uneven terrain, this blade's design ensures that your mower operates at optimal efficiency.

In terms of technology, this blade employs an innovative design that enhances airflow underneath the mower deck. This improved airflow leads to better grass lift and discharge, resulting in an even cut and reducing the chances of clumping. The efficient cutting performance also means that users can optimize their mowing time, making it ideal for those with larger lawns.

The Husqvarna 532 43 65-03,96045002202 is also designed with convenience in mind. Its dimensions and mounting design allow for easy installation and compatibility with a range of Husqvarna mower models. Users can enjoy a hassle-free experience when it comes to maintenance and blade replacement, increasing the overall productivity of their mowing tasks.

In addition to its cutting performance and ease of use, the durable construction of this blade means that it is less prone to wear and tear, providing long-lasting performance even in challenging environments. Customers appreciate the value for money that this blade offers, allowing them to get the most out of their lawn maintenance equipment without the need for frequent replacements.

Overall, the Husqvarna 532 43 65-03,96045002202 lawn mower blade stands out for its exceptional cutting capabilities, advanced design features, and user-friendly handling. Whether you are a homeowner looking to maintain an immaculate lawn or a professional gardener seeking reliable tools, this blade is an excellent choice that combines functionality with longevity.
Top Page Image Contents