Husqvarna 96045002202, 532 43 65-03 Attach Mower Side Suspension Arms a to Chassis See Fig

Page 20

SERVICE AND ADJUSTMENTS

6.ATTACH MOWER SIDE SUSPENSION ARMS (A) TO CHASSIS (See Fig. 29)

•Position front hole in side suspension arm (A) over pin on outside of tractor chassis and secure with large washer and large retainer spring (B).

•Repeat on opposite side of tractor.

A

B

 

D

 

A.MOWER SIDE SUSPENSION ARMS

 

B. RETAINER SPRING

 

D. RIGHT SIDE REAR MOWER BRACKET

 

Fig. 29

7. ATTACH REAR LIFT LINKS (C) (See Fig. 30)

•Insert rod end of rear lift link (C) into hole (U) in tractor lift shaft suspension arm and pivot link down to mower.

•Lift rear corner of mower and position slot in link as- sembly over pin on rear mower bracket (D) and secure with large washer and large retainer spring.

•Repeat on opposite side of tractor.

U

C

D

C. REAR LIFT LINK(S)

D. RIGHT SIDE REAR MOWER BRACKET

U. HOLE

Fig. 30

8 ATTACH FRONT LINK (E) (See Fig. 31)

•Turn steering wheel to position wheels straight forward.

•From front of tractor, insert rod end of front link (E) through front hole in tractor front suspension bracket (F).

•Move to left side of mower and and insert large retainer spring (G) through hole in front link (E) behind front suspension bracket (F).

•Insert other end of link (E) into hole in front mower bracket (H) and secure with washer and small retainer spring (J).

NOTE: Requires deck lifting.

FRONT LINK

LOCATION

M

H

F

G E

J

E.FRONT LIFT LINK ASSEMBLY

F.FRONT SUSPENSION BRACKET

G.LARGE RETAINER SPRING

H.FRONT MOWER BRACKET

J.SMALL RETAINER SPRING M. ENGINE CLUTCH PULLEY

Fig. 31

9INSTALL BELT ON ENGINE CLUTCH PULLEY (M) (See Fig. 21 & 32)

•Disengage belt tension rod (K) from locking bracket (L).

•Install belt onto engine clutch pulley (M).

M

M.ENGINE

CLUTCH PULLEY

Fig. 32

IMPORTANT: Check belt for proper routing in all mower pulley grooves and under mandrel covers.

•Engage belt tension rod (K) on locking bracket (L).

CAUTION: Belt tension rod is spring loaded. Have a tight grip on rod and engage slowly.

•Raise attachment lift to its highest position.

•If necessary, adjust gauge wheels before operat- ing mower as shown in the Operation section of this manual.

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents YTH2348 Safety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService General ServiceIII. Children IV. TowingTable of Contents Assembly Tools Required for AssemblyUnassembled Parts To Remove Tractor from CartonCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor Throttle Control Used to control engine speedHOW to USE Your Tractor To SET Parking Brake See FigStopping See Fig To USE Throttle Control D See FigTo Adjust Mower Cutting Height See Fig To Adjust Gauge Wheels See FigTo Operate Mower Shield S in place. See FigBefore Starting the Engine To Start Engine See Fig Purge TransmissionAutomatic Transmission Warm UP RunningMowing Tips Maintenance MaintenanceGeneral Recommendations ScheduleBattery TractorBlade Care Blade Removal See FigEngine Deck Washout Port See Fig CleaningIN-LINE Fuel Filter See Fig Service and Adjustments To Install Mower and Drive Belt See FigsTo Remove Mower See Fig SET Parking Brake Lever and Lower AT- Tachment Lift See FigSlide Mower Under Tractor See Fig ANTI-SWAY BAR STurn Steering Wheel Left and Position Mower See Fig Install Belt on Engine Clutch Pulley M See Attach Mower Side Suspension Arms a to Chassis See FigAttach Rear Lift Links C See Fig Attach Front Link E See FigTo Level Mower Turn nut right Turn nut left To raise mowerMower Drive Belt Removal Mower Drive Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See Fig To Check BrakeFront Wheel TOE-IN/CAMBER To Remove Wheel for Repairs See FigTo Start Engine with a Weak Battery See Fig Replacing Battery See FigWeak or Dead Fully Charged Battery To Replace Headlight BulbTo Remove Hood and Grill Assembly See Fig To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorStorage OtherFuel System Engine OILProblem Cause Correction To run when oper Battery will notFires when turn Engine continuesSchematic Tractor Model NO. YTH2348 96045002202, Product no 45Electrical KEY Part Description Chassis Chassis 204 532 41 Vent Top Hood196 Drive197 Tractor Model NO. YTH2348 96045002202, Product no 45 Engine Engine Power Rating Information KEY Part NO. NO. DescriptionSteering Assembly 532 41 Wheel, Steering 532 19 Mower Deck KEY Part NO. NO. Description Mower Lift Seat Assembly Decals Wheels and TiresSuggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXService Notes Service Notes Warranty Statement

532 43 65-03, 96045002202 specifications

The Husqvarna 532 43 65-03,96045002202 is a versatile and robust lawn mower blade designed to deliver exceptional cutting performance for a variety of mowing conditions. Known for its reliability and durability, this blade is an essential component for Husqvarna riding mowers and is a favored choice among homeowners and landscaping professionals.

One of the main features of the Husqvarna 532 43 65-03,96045002202 is its sharp cutting edge, made from high-quality steel designed to withstand the rigors of regular use. This blade is engineered to provide a clean and precise cut, promoting healthy grass growth and maintaining the aesthetic appeal of your lawn. Whether you're tackling thick grass, weeds, or uneven terrain, this blade's design ensures that your mower operates at optimal efficiency.

In terms of technology, this blade employs an innovative design that enhances airflow underneath the mower deck. This improved airflow leads to better grass lift and discharge, resulting in an even cut and reducing the chances of clumping. The efficient cutting performance also means that users can optimize their mowing time, making it ideal for those with larger lawns.

The Husqvarna 532 43 65-03,96045002202 is also designed with convenience in mind. Its dimensions and mounting design allow for easy installation and compatibility with a range of Husqvarna mower models. Users can enjoy a hassle-free experience when it comes to maintenance and blade replacement, increasing the overall productivity of their mowing tasks.

In addition to its cutting performance and ease of use, the durable construction of this blade means that it is less prone to wear and tear, providing long-lasting performance even in challenging environments. Customers appreciate the value for money that this blade offers, allowing them to get the most out of their lawn maintenance equipment without the need for frequent replacements.

Overall, the Husqvarna 532 43 65-03,96045002202 lawn mower blade stands out for its exceptional cutting capabilities, advanced design features, and user-friendly handling. Whether you are a homeowner looking to maintain an immaculate lawn or a professional gardener seeking reliable tools, this blade is an excellent choice that combines functionality with longevity.
Top Page Image Contents