Husqvarna 532 43 65-03, 96045002202 Tractor, Blade Care, Blade Removal See Fig, Battery

Page 15

MAINTENANCE

TRACTOR

Always observe safety rules when performing any maintenance.

BRAKE OPERATION

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted. (See “TO CHECK BRAKE” in the Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See the sides of tires for proper PSI).

•Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM AND REVERSE OPERATION SYSTEM (ROS) (See Fig. 14)

Be sure operator presence and reverse operation systems are working properly. If your tractor does not function as described, repair the problem immediately.

•The engine should not start unless the brake pedal is fully depressed, and the attachment clutch control is in the disengaged position.

CHECK OPERATOR PRESENCE SYSTEM

• When the engine is running, any attempt by the operator

to leave the seat without first setting the parking brake

should shut off the engine.

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

CAUTION: Use only a replacement blade ap- proved by the manufacturer of your tractor. Using a blade not approved by the manu- facturer of your tractor is hazardous, could damage your tractor and void your warranty.

BLADE REMOVAL (See Fig. 15)

•Raise mower to highest position to allow access to blades.

NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth.

•Remove blade bolt by turning counterclockwise.

•Install new or resharpened blade with stamped "THIS SIDE UP" facing deck and mandrel assembly.

IMPORTANT: To ensure proper assembly, center hole in blade must align with star on mandrel assembly.

•Install and tighten blade bolt securely (45-55 Ft. Lbs. torque).

IMPORTANT: SPECIAL BLADE BOLT HEAT TREATED.

MANDREL ASSEMBLY

 

BLADE

BLADE BOLT

STAR

(SPECIAL)

 

CENTER HOLE

• When the engine is running and the attachment clutch

is engaged, any attempt by the operator to leave the

BATTERY

Fig. 15

seat should shut off the engine.

• The attachment clutch should never operate unless

the operator is in the seat.

CHECK REVERSE OPERATION (ROS) SYSTEM

•When the engine is running with the ignition switch in the engine "ON" position and the attachment clutch engaged, any attempt by the operator to shift into reverse should shut off the engine.

•When the engine is running with the ignition switch in the ROS "ON" position and the attachment clutch engaged, any attempt by the operator to shift into reverse should NOT shut off the engine.

 

 

 

 

 

 

 

 

 

 

02828

ROS "ON"

ENGINE "ON" POSITION

POSITION

(NORMAL OPERATING)

 

 

 

 

 

 

Fig. 14

Your tractor has a battery charging system which is sufficient for normal use. However, periodic charging of the battery with an automotive charger will extend its life.

•Keep battery and terminals clean.

•Keep battery bolts tight.

•Keep small vent holes open.

•Recharge at 6-10 amperes for 1 hour.

NOTE:Theoriginalequipmentbatteryonyourtractorismain- tenance free. Do not attempt to open or remove caps or cov- ers. Adding or checking level of electrolyte is not necessary.

TO CLEAN BATTERY AND TERMINALS

Corrosion and dirt on the battery and terminals can cause the battery to “leak” power.

•Remove terminal guard.

•Disconnect BLACK battery cable first then RED bat- tery cable and remove battery from tractor.

•Rinse the battery with plain water and dry.

•Clean terminals and battery cable ends with wire brush until bright.

•Coat terminals with grease or petroleum jelly.

•Reinstall battery (See “REPLACING BATTERY" in the Service and Adjustments section of this manual).

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents YTH2348 II. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIV. Towing ServiceGeneral Service III. ChildrenTable of Contents To Remove Tractor from Carton AssemblyTools Required for Assembly Unassembled PartsCheck Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Throttle Control Used to control engine speed Know Your TractorTo USE Throttle Control D See Fig HOW to USE Your TractorTo SET Parking Brake See Fig Stopping See FigShield S in place. See Fig To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Operate MowerBefore Starting the Engine Running To Start Engine See FigPurge Transmission Automatic Transmission Warm UPMowing Tips Schedule MaintenanceMaintenance General RecommendationsBlade Removal See Fig BatteryTractor Blade CareEngine Cleaning IN-LINE Fuel Filter See FigDeck Washout Port See Fig SET Parking Brake Lever and Lower AT- Tachment Lift See Fig Service and AdjustmentsTo Install Mower and Drive Belt See Figs To Remove Mower See FigANTI-SWAY BAR S Turn Steering Wheel Left and Position Mower See FigSlide Mower Under Tractor See Fig Attach Front Link E See Fig Install Belt on Engine Clutch Pulley M SeeAttach Mower Side Suspension Arms a to Chassis See Fig Attach Rear Lift Links C See FigTurn nut right Turn nut left To raise mower To Level MowerMower Drive Belt Installation To Replace Mower Blade Drive Belt See FigMower Drive Belt Removal To Remove Wheel for Repairs See Fig To Replace Motion Drive Belt See FigTo Check Brake Front Wheel TOE-IN/CAMBERTo Replace Headlight Bulb To Start Engine with a Weak Battery See FigReplacing Battery See Fig Weak or Dead Fully Charged BatteryTo Adjust Carburetor To Remove Hood and Grill Assembly See FigTo Adjust Throttle Control Cable To Adjust Choke ControlEngine OIL StorageOther Fuel SystemProblem Cause Correction Engine continues To run when operBattery will not Fires when turnTractor Model NO. YTH2348 96045002202, Product no 45 SchematicElectrical KEY Part Description Chassis 204 532 41 Vent Top Hood ChassisDrive 197196 Tractor Model NO. YTH2348 96045002202, Product no 45 Engine KEY Part NO. NO. Description Engine Power Rating InformationSteering Assembly 532 41 Wheel, Steering 532 19 Mower Deck KEY Part NO. NO. Description Mower Lift Seat Assembly Wheels and Tires DecalsOnly Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationService Notes Service Notes Warranty Statement

532 43 65-03, 96045002202 specifications

The Husqvarna 532 43 65-03,96045002202 is a versatile and robust lawn mower blade designed to deliver exceptional cutting performance for a variety of mowing conditions. Known for its reliability and durability, this blade is an essential component for Husqvarna riding mowers and is a favored choice among homeowners and landscaping professionals.

One of the main features of the Husqvarna 532 43 65-03,96045002202 is its sharp cutting edge, made from high-quality steel designed to withstand the rigors of regular use. This blade is engineered to provide a clean and precise cut, promoting healthy grass growth and maintaining the aesthetic appeal of your lawn. Whether you're tackling thick grass, weeds, or uneven terrain, this blade's design ensures that your mower operates at optimal efficiency.

In terms of technology, this blade employs an innovative design that enhances airflow underneath the mower deck. This improved airflow leads to better grass lift and discharge, resulting in an even cut and reducing the chances of clumping. The efficient cutting performance also means that users can optimize their mowing time, making it ideal for those with larger lawns.

The Husqvarna 532 43 65-03,96045002202 is also designed with convenience in mind. Its dimensions and mounting design allow for easy installation and compatibility with a range of Husqvarna mower models. Users can enjoy a hassle-free experience when it comes to maintenance and blade replacement, increasing the overall productivity of their mowing tasks.

In addition to its cutting performance and ease of use, the durable construction of this blade means that it is less prone to wear and tear, providing long-lasting performance even in challenging environments. Customers appreciate the value for money that this blade offers, allowing them to get the most out of their lawn maintenance equipment without the need for frequent replacements.

Overall, the Husqvarna 532 43 65-03,96045002202 lawn mower blade stands out for its exceptional cutting capabilities, advanced design features, and user-friendly handling. Whether you are a homeowner looking to maintain an immaculate lawn or a professional gardener seeking reliable tools, this blade is an excellent choice that combines functionality with longevity.
Top Page Image Contents