Husqvarna 96045002202, 532 43 65-03 owner manual Service and Adjustments, To Remove Mower See Fig

Page 18

SERVICE AND ADJUSTMENTS

WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUST- MENTS:

•Depress brake pedal fully and set parking brake.

•Place attachment clutch in “DISENGAGED” position.

•Turn ignition key to “STOP” and remove key.

•Make sure the blades and all moving parts have completely stopped.

•Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

TO REMOVE MOWER (See Fig. 21)

•Place attachment clutch in “DISENGAGED” position.

•Lower attachment lift to its lowest position.

•Disengage belt tension rod (K) from lock bracket (L).

CAUTION: Belt tension rod is spring loaded. Have a tight grip on rod and release slowly.

•Remove mower belt from electric clutch pulley (M).

•Disconnect front link (E) from mower - remove retainer spring and washer.

•Gotoeithersideofmoweranddisconnectmowersuspen- sion arm (A) from chassis and rear lift link (C) from rear mowerbracket(D)-removeretainerspringsandwashers.

•Go to other side of mower and disconnect the suspen- sion arm and rear lift link.

CAUTION: After rear lift links are discon- nected, the attachment lift lever will be spring loaded. Have a tight grip on lift le- ver when changing position of the lever.

•From right side of mower, disconnect anti-sway bar (S) from right rear mower bracket (D) - remove retainer spring and washer and pull mower toward you until the bar falls from the hole in bracket.

•Turn tractor steering wheel to the left as far as it will go.

•Slide mower out from under right side of tractor.

TO INSTALL MOWER AND DRIVE BELT (See Figs. 21 - 32)

1.SET PARKING BRAKE LEVER AND LOWER AT- TACHMENT LIFT (See Fig. 20)

•Depress clutch/brake pedal all the way down and hold.

•Pull parking brake lever up and hold, release pressure from clutch/brake pedal, then release parking brake lever. Pedal should remain in brake position. Ensure parking brake will hold tractor secure.

PARKING

BRAKE

LEVER

Fig. 22

•The attachment lift switch is used to raise and lower the mower deck or other attachments mounted to your tractor. Ignition must be on to operate this switch.

•Lower attachment lift to its lowest position.

CAUTION: Continuing to press the electric lift switch after the mower deck has reached the minimum or maximum position may result in damage to the electric lift mechanism.The electric lift mechanism is equipped with a thermal protection system. If the system overheats or fails to operate, allow the sys- tem to cool before attempting to operate again.

K

C

I

 

M

F

 

A. MOWER SIDE SUSPENSION

L B

 

 

 

 

 

 

 

 

 

ARMS

 

 

 

W

B. RETAINER SPRING

 

A

 

C. REAR LIFT LINK(S)

 

 

 

 

 

E

 

D. RIGHT SIDE REAR MOWER

 

 

 

BRACKET

 

 

 

 

E. FRONT LIFT LINK ASSEMBLY

 

 

 

 

F. FRONT SUSPENSION BRACKET

 

 

 

 

H. FRONT MOWER BRACKET

 

 

 

H

I. LEFT SIDE REAR MOWER

 

 

 

 

BRACKET

 

 

 

 

K. BELT TENSION ROD

 

 

 

 

L. LOCKING BRACKET

 

 

 

 

M. ENGINE CLUTCH PULLEY

 

 

 

 

Q. DEFLECTOR SHIELD

C

 

 

 

S. ANTI-SWAY BAR

S

D

 

 

W. FRONT GAUGE WHEEL

 

Q

 

Fig. 19

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents YTH2348 General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts AssemblyTools Required for Assembly To Remove Tractor from CartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor Throttle Control Used to control engine speedStopping See Fig HOW to USE Your TractorTo SET Parking Brake See Fig To USE Throttle Control D See FigTo Operate Mower To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig Shield S in place. See FigBefore Starting the Engine Automatic Transmission Warm UP To Start Engine See FigPurge Transmission RunningMowing Tips General Recommendations MaintenanceMaintenance ScheduleBlade Care BatteryTractor Blade Removal See FigEngine Cleaning IN-LINE Fuel Filter See FigDeck Washout Port See Fig To Remove Mower See Fig Service and AdjustmentsTo Install Mower and Drive Belt See Figs SET Parking Brake Lever and Lower AT- Tachment Lift See FigANTI-SWAY BAR S Turn Steering Wheel Left and Position Mower See FigSlide Mower Under Tractor See Fig Attach Rear Lift Links C See Fig Install Belt on Engine Clutch Pulley M SeeAttach Mower Side Suspension Arms a to Chassis See Fig Attach Front Link E See FigTo Level Mower Turn nut right Turn nut left To raise mowerMower Drive Belt Installation To Replace Mower Blade Drive Belt See FigMower Drive Belt Removal Front Wheel TOE-IN/CAMBER To Replace Motion Drive Belt See FigTo Check Brake To Remove Wheel for Repairs See FigWeak or Dead Fully Charged Battery To Start Engine with a Weak Battery See FigReplacing Battery See Fig To Replace Headlight BulbTo Adjust Choke Control To Remove Hood and Grill Assembly See FigTo Adjust Throttle Control Cable To Adjust CarburetorFuel System StorageOther Engine OILProblem Cause Correction Fires when turn To run when operBattery will not Engine continuesSchematic Tractor Model NO. YTH2348 96045002202, Product no 45Electrical KEY Part Description Chassis Chassis 204 532 41 Vent Top HoodDrive 197196 Tractor Model NO. YTH2348 96045002202, Product no 45 Engine Engine Power Rating Information KEY Part NO. NO. DescriptionSteering Assembly 532 41 Wheel, Steering 532 19 Mower Deck KEY Part NO. NO. Description Mower Lift Seat Assembly Decals Wheels and TiresSuggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXService Notes Service Notes Warranty Statement

532 43 65-03, 96045002202 specifications

The Husqvarna 532 43 65-03,96045002202 is a versatile and robust lawn mower blade designed to deliver exceptional cutting performance for a variety of mowing conditions. Known for its reliability and durability, this blade is an essential component for Husqvarna riding mowers and is a favored choice among homeowners and landscaping professionals.

One of the main features of the Husqvarna 532 43 65-03,96045002202 is its sharp cutting edge, made from high-quality steel designed to withstand the rigors of regular use. This blade is engineered to provide a clean and precise cut, promoting healthy grass growth and maintaining the aesthetic appeal of your lawn. Whether you're tackling thick grass, weeds, or uneven terrain, this blade's design ensures that your mower operates at optimal efficiency.

In terms of technology, this blade employs an innovative design that enhances airflow underneath the mower deck. This improved airflow leads to better grass lift and discharge, resulting in an even cut and reducing the chances of clumping. The efficient cutting performance also means that users can optimize their mowing time, making it ideal for those with larger lawns.

The Husqvarna 532 43 65-03,96045002202 is also designed with convenience in mind. Its dimensions and mounting design allow for easy installation and compatibility with a range of Husqvarna mower models. Users can enjoy a hassle-free experience when it comes to maintenance and blade replacement, increasing the overall productivity of their mowing tasks.

In addition to its cutting performance and ease of use, the durable construction of this blade means that it is less prone to wear and tear, providing long-lasting performance even in challenging environments. Customers appreciate the value for money that this blade offers, allowing them to get the most out of their lawn maintenance equipment without the need for frequent replacements.

Overall, the Husqvarna 532 43 65-03,96045002202 lawn mower blade stands out for its exceptional cutting capabilities, advanced design features, and user-friendly handling. Whether you are a homeowner looking to maintain an immaculate lawn or a professional gardener seeking reliable tools, this blade is an excellent choice that combines functionality with longevity.
Top Page Image Contents