Husqvarna 1153176-95, 385XPG, 390XPG Assembly, Fitting the bar and chain, Working with the chain

Page 17

ASSEMBLY

Fitting the bar and chain

	!	WARNING! Always wear gloves, when
	!	working with the chain.
		working with the chain.

Check that the chain brake is in disengaged position by moving the front hand guard towards the front handle.

Remove the bar nuts and remove the clutch cover (chain brake). Take off the transportation ring (A).

Fit the bar over the bar bolts. Place the bar in its rearmost position. Place the chain over the drive sprocket locate it in the groove on the bar. Begin on the top edge of the bar.

Make sure that the edges of the cutting links are facing forward on the top edge of the bar.

Fit the clutch cover and locate the chain adjuster pin in the hole in the bar. Check that the drive links of the chain ﬁt correctly over the drive sprocket and that the chain is correctly located in the groove in the bar. Tighten the bar nuts ﬁnger tight.

Tension the chain by turning the chain tensioning screw clockwise using the combination spanner.

The chain is correctly tensioned when it does not sag from the underside of the bar, but can still be turned easily by hand. Hold up the bar tip and tighten the bar nuts with the combination spanner.

When ﬁtting a new chain, the chain tension has to be checked frequently until the chain is run-in. Check the chain tension regularly. A correctly tensioned chain ensures good cutting performance and long life.

Note: If clutch cover is difﬁcult to remove, replace bar nuts, engage brake and rerelease (an audible click will be heard if released properly).

English – 17

Image 17

Contents 385XP 385XPG 390XP 390XPG Symbols in the operator’s manual KEY to SymbolsSymbols on the machine EPA Contents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?Always use common sense General Safety PrecautionsBefore using a new chain saw Chain brake and front hand guard Machine′s safety equipmentPersonal protective equipment General Safety Precautions Chain catcher Throttle lockoutRight hand guard Vibration damping systemCutting equipment Stop switchMufﬂer General rulesChain Cutting equipment designed to reduce kickbackBar General information on sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingLubricating cutting equipment Tensioning the chainChecking chain lubrication Filling with chain oilChain drive sprocket Needle bearing lubricationChecking wear on cutting equipment Working with the chain AssemblyFitting the bar and chain Fuel Fuel HandlingFueling Fuel safetyTransport and storage Long-term storageStarting and stopping Starting and StoppingCold engine Warm engineStopping Working Techniques Basic safety rulesBefore use General working instructionsGeneral rules Terms Basic cutting techniqueLimbing Tree felling techniqueSafe distance Felling directionDirectional cuts Clearing the trunk and preparing your retreatFelling cut Freeing a tree that has fallen badlyFreeing a trapped tree Cutting trees and branches that are in tensionWhat is kickback? How to avoid kickbackGeneral advice Cutting the trunk into logsGeneral MaintenanceCarburetor adjustment Correctly adjusted carburetor Fine adjustment of the idling speed THigh speed jet H Checking brake band wearImmediately Checking the inertia brake releaseMufﬂer Tensioning the recoil spring StarterChanging a broken or worn starter cord Spark plug Air ﬁlterChanging a broken recoil spring Fitting the starterWhen making adjustments Adjustment of the oil pumpLubricating the bar tip sprocket Needle bearing lubricationTemperature 0C 32F or colder Air Injection centrifugal cleaningWinter use Heated handlesDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical Data058/1,5 mm Saw chain ﬁling and ﬁle gauges050/1,3 mm Your Warranty Rights and Obligations Federal Emission Control Warranty StatementEmission Controlwarranty Parts List Safety precautions for chain saw users American Standard Safety PrecautionsKickback safety precautions Other safety precautionsPage Original instructions 1153176-95