Husqvarna 1153176-95 KEY to Symbols, Symbols on the machine, Symbols in the operator’s manual

Page 2

KEY TO SYMBOLS

Symbols on the machine:

WARNING! Chain saws can be dangerous! Careless or improper use can result in serious or fatal injury to the operator or others.

Please read the operator’s manual carefully and make sure you understand the instructions before using the machine.

Always wear:

•Approved protective helmet

• Approved hearing protection

• Protective goggles or a visor

Both of the operator′s hands must be used to operate the chain saw.

Never operate a chain saw holding it with one hand only.

Contact of the guide bar tip with any object must be avoided.

WARNING! Kickback may occur when the nose or tip of the guide bar touches an object, and cause a lightning fast reverse reaction, kicking the guide bar up and towards the operator. May cause serious personal injury.

Decompression valve: The valve is to reduce the pressure in the cylinder and make starting easier. You should always use the decompression valve when starting the machine.

Ignition; choke: Set the choke control in the choke position. This should automatically set the stop switch to the start position.

Adjustment of the oil pump

Chain brake, activated (right)

Chain brake, not activated (left)

Other symbols/decals on the machine refer to special certiﬁcation requirements for certain markets.

2 – English

Symbols in the operator’s manual:

Switch off the engine by moving the stop switch to the STOP position before carrying out any checks or maintenance.

Always wear approved protective gloves.

Regular cleaning is required.

Visual check.

Protective goggles or a visor must be worn.

Refuelling.

Filling with oil and adjusting oil ﬂow.

The chain brake must be engaged when the chain saw is started.

WARNING! Kickback may occur when the nose or tip of the guide bar touches an object, and cause a lightning fast reverse reaction, kicking the guide bar up and towards the operator. May cause serious personal injury.

The engine exhaust from this product contains chemical known to the State of California to cause cancer, birth defects or other reproductive harm.

Image 2

Contents 385XP 385XPG 390XP 390XPG Symbols in the operator’s manual KEY to SymbolsSymbols on the machine EPA Contents Introduction Dear customerWhat is WHAT? What is what on the chain saw?Always use common sense General Safety PrecautionsBefore using a new chain saw Chain brake and front hand guard Machine′s safety equipmentPersonal protective equipment General Safety Precautions Right hand guard Throttle lockoutChain catcher Vibration damping systemMufﬂer Stop switchCutting equipment General rulesChain Cutting equipment designed to reduce kickbackBar Sharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethTensioning the chain Lubricating cutting equipmentChain drive sprocket Filling with chain oilChecking chain lubrication Needle bearing lubricationChecking wear on cutting equipment Working with the chain AssemblyFitting the bar and chain Fuel Handling FuelTransport and storage Fuel safetyFueling Long-term storageCold engine Starting and StoppingStarting and stopping Warm engineStopping Before use Basic safety rulesWorking Techniques General working instructionsGeneral rules Basic cutting technique TermsSafe distance Tree felling techniqueLimbing Felling directionClearing the trunk and preparing your retreat Directional cutsFreeing a trapped tree Freeing a tree that has fallen badlyFelling cut Cutting trees and branches that are in tensionGeneral advice How to avoid kickbackWhat is kickback? Cutting the trunk into logsGeneral MaintenanceCarburetor adjustment High speed jet H Fine adjustment of the idling speed TCorrectly adjusted carburetor Checking brake band wearChecking the inertia brake release ImmediatelyMufﬂer Tensioning the recoil spring StarterChanging a broken or worn starter cord Changing a broken recoil spring Air ﬁlterSpark plug Fitting the starterLubricating the bar tip sprocket Adjustment of the oil pumpWhen making adjustments Needle bearing lubricationWinter use Air Injection centrifugal cleaningTemperature 0C 32F or colder Heated handlesMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical data058/1,5 mm Saw chain ﬁling and ﬁle gauges050/1,3 mm Federal Emission Control Warranty Statement Your Warranty Rights and ObligationsEmission Controlwarranty Parts List Kickback safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Other safety precautionsPage Original instructions 1153176-95