Husqvarna 1153176-95 manual Starting and Stopping, Starting and stopping, Cold engine, Warm engine

Page 20

STARTING AND STOPPING

Starting and stopping

WARNING! Note the following before

!starting:

The chain brake must be engaged when the chain saw is started to reduce the chance of contact with the moving chain during starting.

Never start a chain saw unless the bar, chain and all covers are ﬁtted correctly. Otherwise the clutch can come loose and cause personal injuries.

Place the machine on ﬁrm ground. Make sure you have a secure footing and that the chain cannot touch anything.

Keep people and animals well away from the working area.

Cold engine

Starting: The chain brake should be activated when starting the chain saw. Activate the chain brake by pushing the front hand guard forwards.

Ignition: Slide the ignition switch to the left.

Choke: Set the choke control in the choke position.

Start throttle: The correct choke/start throttle setting is obtained by moving the control to the choke position.

If the machine is ﬁtted with a decompression valve (A): Press the valve to reduce the pressure in the cylinder and make starting easier. You should always use the decompression valve when starting the machine. Once the machine has started the valve will automatically return to its original setting.

A

Warm engine

Use the same procedure as for starting a cold engine but without setting the choke control in the choke position. The correct choke/start throttle setting is obtained by moving the choke control to the choke position and then pushing it in again.

Starting

Grip the front handle with your left hand. Hold the chain saw on the ground by placing your right foot through the rear handle. Pull the starter handle with your right hand and pull out the starter cord slowly until you feel a resistance (as the starter pawls engage) then pull ﬁrmly and rapidly. Never wrap the starter cord around your

hand

CAUTION! Do not pull the starter cord all the way out and do not let go of the starter handle when the cord is fully extended. This can damage the machine.

20 – English

Image 20

Contents 385XP 385XPG 390XP 390XPG Symbols in the operator’s manual KEY to SymbolsSymbols on the machine EPA Contents Introduction Dear customerWhat is WHAT? What is what on the chain saw?Always use common sense General Safety PrecautionsBefore using a new chain saw Chain brake and front hand guard Machine′s safety equipmentPersonal protective equipment General Safety Precautions Throttle lockout Chain catcherRight hand guard Vibration damping systemStop switch Cutting equipmentMufﬂer General rulesChain Cutting equipment designed to reduce kickbackBar Sharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethTensioning the chain Lubricating cutting equipmentFilling with chain oil Checking chain lubricationChain drive sprocket Needle bearing lubricationChecking wear on cutting equipment Working with the chain AssemblyFitting the bar and chain Fuel Handling FuelFuel safety FuelingTransport and storage Long-term storageStarting and Stopping Starting and stoppingCold engine Warm engineStopping Basic safety rules Working TechniquesBefore use General working instructionsGeneral rules Basic cutting technique TermsTree felling technique LimbingSafe distance Felling directionClearing the trunk and preparing your retreat Directional cutsFreeing a tree that has fallen badly Felling cutFreeing a trapped tree Cutting trees and branches that are in tensionHow to avoid kickback What is kickback?General advice Cutting the trunk into logsGeneral MaintenanceCarburetor adjustment Fine adjustment of the idling speed T Correctly adjusted carburetorHigh speed jet H Checking brake band wearChecking the inertia brake release ImmediatelyMufﬂer Tensioning the recoil spring StarterChanging a broken or worn starter cord Air ﬁlter Spark plugChanging a broken recoil spring Fitting the starterAdjustment of the oil pump When making adjustmentsLubricating the bar tip sprocket Needle bearing lubricationAir Injection centrifugal cleaning Temperature 0C 32F or colderWinter use Heated handlesMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical data058/1,5 mm Saw chain ﬁling and ﬁle gauges050/1,3 mm Federal Emission Control Warranty Statement Your Warranty Rights and ObligationsEmission Controlwarranty Parts List American Standard Safety Precautions Safety precautions for chain saw usersKickback safety precautions Other safety precautionsPage Original instructions 1153176-95