Husqvarna 385XP, 390XP Tensioning the chain, General advice on adjusting depth gauge setting

Page 13

GENERAL SAFETY PRECAUTIONS

General advice on adjusting depth gauge setting

•When you sharpen the cutting tooth (A) the depth gauge setting (C) will decrease. To maintain optimal cutting performance the depth gauge (B) has to be filed down to achieve the recommended depth gauge setting. See instructions under the heading Technical data to find the correct depth gauge setting for your particular chain.

WARNING! The risk of kickback is increased

!if the depth gauge setting is too large!

Adjustment of depth gauge setting

•The cutting teeth should be newly sharpened before adjusting the depth gauge setting. We recommend that you adjust the depth gauge setting every third time you sharpen the cutting teeth. NOTE! This recommendation assumes that the length of the cutting teeth is not reduced excessively.

•You will need a flat file and a depth gauge tool. We recommend that you use our depth gauge tool to acheive the correct depth gauge setting and bevel for the depth gauge.

•Place the depth gauge tool over the chain. Detailed information regarding the use of the depth gauge tool, will be found on the package for the depth gauge tool. Use the flat file to file off the tip of the depth gauge that protrudes through the depth gauge tool. The depth gauge setting is correct when you no longer feel resistance as you draw the file along the depth gauge tool.

Tensioning the chain

WARNING! A slack chain may jump off the

!bar and cause serious or even fatal injury.

The more you use a chain the longer it becomes. It is therefore important to adjust the chain regularly to take up the slack.

Check the chain tension every time you refuel. NOTE! A new chain has a running-in period during which you should check the tension more frequently.

Tension the chain as tightly as possible, but not so tight that you cannot pull it round freely by hand.

•Loosen the bar nuts that hold the clutch cover/chain brake. Use the combination spanner. Then tighten the bar nuts by hand as tight as you can.

•Raise the tip of the bar and stretch the chain by tightening the chain tensioning screw using the combination spanner. Tighten the chain until it does not sag from the underside of the bar.

•Use the combination spanner to tighten the bar nuts while lifting the tip of the bar at the same time. Check that you can pull the chain round freely by hand and that it does not sag from the underside of the bar.

The position of the chain tensioning screw on our chain saws varies from model to model. See instructions under the heading What is what? to find out where it is on your model.

English – 13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents 385XP 390XP Symbols on the machine KEY to SymbolsSymbols in the operator’s manual You will find the following labels on your chain sawContents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?Before using a new chain saw General Safety PrecautionsAlways use common sense Personal protective equipment Machine′s safety equipmentChain brake and front hand guard General Safety Precautions Chain catcher Throttle lockRight hand guard Cutting equipment Stop switchVibration damping system MufflerCutting equipment designed to reduce kickback General rulesBar ChainGeneral information on sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingSharpening cutting teeth Instructions considerably increases the risk of kickbackAdjustment of depth gauge setting General advice on adjusting depth gauge settingIf the depth gauge setting is too large Tensioning the chainChain oil Lubricating cutting equipmentFilling with chain oil Checking chain lubricationNeedle bearing lubrication Chain drive sprocketChecking wear on cutting equipment Fitting the bar and chain AssemblyFuel Fuel HandlingFueling Fuel safetyTransport and storage Long-term storageStarting and stopping Starting and StoppingCold engine Warm engineStopping Working Techniques Basic safety rulesBefore use General working instructionsGeneral rules General Basic cutting techniqueTerms Cutting LimbingSafe distance Tree felling techniqueFelling direction Clearing the trunk and preparing your retreatDirectional cuts FellingFelling cut Freeing a tree that has fallen badly General adviceFreeing a trapped tree Cutting trees and branches that are in tensionWhat is kickback? How to avoid kickbackCutting the trunk into logs Carburetor adjustment MaintenanceGeneral High speed jet H Correctly adjusted carburetorChecking brake band wear Checking the front hand guardChecking the brake trigger Starter MufflerChanging a broken or worn starter cord Tensioning the recoil spring Air filterChanging a broken recoil spring Fitting the starterWhen making adjustments Adjustment of the oil pumpSpark plug Lubricating the bar tip sprocketCooling system Air Injection centrifugal cleaningWinter use Heated handlesDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical Data050/1,3 mm Saw chain filing and file gauges058/1,5 mm Your Warranty Rights and Obligations Federal Emission Control Warranty StatementSafety precautions for chain saw users American Standard Safety PrecautionsKickback safety precautions Other safety precautionsPage ´z+R1=¶5¨ Page 1150172-95 ´z+R1=¶5¨ ´z+R1=¶5¨
Top Page Image Contents