Husqvarna 385XP, 390XP manual Saw chain ﬁling and ﬁle gauges, 050/1,3 mm, 058/1,5 mm

Page 38

TECHNICAL DATA

Recommended original and replacement bar and chain combinations

These Husqvarna chain saw models are in the ANSI category of saws above 3,8 cu. in. and are not required to comply with low kickback performance requirements. However, for these models we recommend the following cutting equipment.

		Bar			Chain

Length, inch	Pitch, inch	Gauge, inch	Max. nose radius	Type		Drive link count

18-28	3/8"	0,058	11T	Husqvarna H42,		68-92
				Husqvarna H48,
18-28	3/8"	0,058	ATM 1,33”	Husqvarna H48,		68-92
18-28	3/8"	0,058	ATM 1,33”	Husqvarna H81		68-92
				Husqvarna H81

Listed ATM is the Oregon designation of Armour Tip Medium hard nose bar.

Note: For the chains above you are free to choose between 0,050" and 0,058" gauge drive link for the corresponding bar, see the table below.

0,050"/1,3 mm	H46	H47	H80

0,058"/1,5 mm	H42	H48	H81

WARNING! This chain saw model is capable

!of severe kickback that could result in serious injuries to the user. Do not operate this saw unless you have extraordinary cutting needs and experience and specialized training for dealing with kickback. Saws with signiﬁcantly reduced kickback potential are available. Always use the safest saw and cutting equipment applicable to your cutting need.

Saw chain ﬁling and ﬁle gauges

38 – English

Image 38

Contents 385XP 390XP Symbols in the operator’s manual KEY to SymbolsSymbols on the machine You will ﬁnd the following labels on your chain sawContents Introduction Dear customerWhat is WHAT? What is what on the chain saw?Always use common sense General Safety PrecautionsBefore using a new chain saw Chain brake and front hand guard Machine′s safety equipmentPersonal protective equipment General Safety Precautions Right hand guard Throttle lockChain catcher Vibration damping system Stop switchCutting equipment MufﬂerBar General rulesCutting equipment designed to reduce kickback ChainSharpening cutting teeth Sharpening your chain and adjusting depth gauge settingGeneral information on sharpening cutting teeth Instructions considerably increases the risk of kickbackIf the depth gauge setting is too large General advice on adjusting depth gauge settingAdjustment of depth gauge setting Tensioning the chainFilling with chain oil Lubricating cutting equipmentChain oil Checking chain lubricationChecking wear on cutting equipment Chain drive sprocketNeedle bearing lubrication Assembly Fitting the bar and chainFuel Handling FuelTransport and storage Fuel safetyFueling Long-term storageCold engine Starting and StoppingStarting and stopping Warm engineStopping Before use Basic safety rulesWorking Techniques General working instructionsGeneral rules Terms Basic cutting techniqueGeneral Limbing CuttingFelling direction Tree felling techniqueSafe distance Clearing the trunk and preparing your retreatFelling cut FellingDirectional cuts Freeing a trapped tree General adviceFreeing a tree that has fallen badly Cutting trees and branches that are in tensionCutting the trunk into logs How to avoid kickbackWhat is kickback? General MaintenanceCarburetor adjustment Checking brake band wear Correctly adjusted carburetorHigh speed jet H Checking the front hand guardChecking the brake trigger Changing a broken or worn starter cord MufﬂerStarter Changing a broken recoil spring Air ﬁlterTensioning the recoil spring Fitting the starterSpark plug Adjustment of the oil pumpWhen making adjustments Lubricating the bar tip sprocketWinter use Air Injection centrifugal cleaningCooling system Heated handlesMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical data058/1,5 mm Saw chain ﬁling and ﬁle gauges050/1,3 mm Federal Emission Control Warranty Statement Your Warranty Rights and ObligationsKickback safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Other safety precautionsPage ´z+R1=¶5¨ Page 1150172-95 ´z+R1=¶5¨ ´z+R1=¶5¨