Husqvarna 385XP, 390XP manual Fueling, Fuel safety, Transport and storage, Long-term storage

Page 18

FUEL HANDLING

Fueling

WARNING! Taking the following precautions,

!will lessen the risk of fire:

Do not smoke and do not place any hot objects in the vicinity of fuel.

Always stop the engine and let it cool for a few minutes before refuelling.

When refuelling, open the fuel cap slowly so that any excess pressure is released gently.

Tighten the fuel cap carefully after refuelling.

Always move the machine away from the refuelling area before starting.

Clean the area around the fuel cap. Clean the fuel and chain oil tanks regularly. The fuel filter must be replaced at least once a year. Contamination in the tanks causes malfunction. Make sure the fuel is well mixed by shaking the container before refuelling. The capacities of the chain oil tank and fuel tank are carefully matched. You should therefore always fill the chain oil tank and fuel tank at the same time.

Min 3 m

(10ft)

WARNING! Fuel and fuel vapor are highly

!flammable.Take care when handling fuel and chain oil. Be aware of the risks of fire, explosion and those associated with inhalation.

Fuel safety

•Never refuel the machine while the engine is running.

•Make sure there is plenty of ventilation when refuelling or mixing fuel (gasoline and 2-stroke oil).

•Move the machine at least 3 m from the refuelling point before starting it.

•Never start the machine:

1If you have spilt fuel or chain oil on the machine. Wipe off the spillage and allow remaining fuel to evaporate.

2If you have spilt fuel on yourself or your clothes, change your clothes. Wash any part of your body that has come in contact with fuel. Use soap and water.

3If the machine is leaking fuel. Check regularly for leaks from the fuel cap and fuel lines.

WARNING! Never use a machine with visible

!damage to the spark plug guard and ignition cable. A risk of sparking arises, which can cause a fire.

Transport and storage

•Always store the chain saw and fuel so that there is no risk of leakages or fumes coming into contact with sparks or naked flames from electrical equipment, electric motors, relays/switches, boilers and the like.

•Always store fuel in an approved container designed for that purpose.

•For longer periods of storage or for transport of the chain saw, the fuel and chain oil tanks should be emptied. Ask where you can dispose of waste fuel and chain oil at your local gas station.

•Ensure the machine is cleaned and that a complete service is carried out before long-term storage.

•The bar guard must always be fitted to the cutting attachment when the machine is being transported or in storage, in order to prevent accident contact with the sharp chain. Even a non-moving chain can cause serious cuts to yourself or persons you bump into with an exposed chain.

Long-term storage

Empty the fuel/oil tanks in a well ventilated area. Store the fuel in approved cans in a safe place. Fit the bar guard. Clean the machine. See instructions under the heading Maintenance schedule.

18 – English

Page 17 Page 19
Image 18
Page 17 Page 19
Contents 385XP 390XP Symbols in the operator’s manual KEY to SymbolsSymbols on the machine You will find the following labels on your chain sawContents Introduction Dear customerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawAlways use common sense Machine′s safety equipment Personal protective equipmentChain brake and front hand guard General Safety Precautions Throttle lock Chain catcherRight hand guard Vibration damping system Stop switchCutting equipment MufflerBar General rulesCutting equipment designed to reduce kickback ChainSharpening cutting teeth Sharpening your chain and adjusting depth gauge settingGeneral information on sharpening cutting teeth Instructions considerably increases the risk of kickbackIf the depth gauge setting is too large General advice on adjusting depth gauge settingAdjustment of depth gauge setting Tensioning the chainFilling with chain oil Lubricating cutting equipmentChain oil Checking chain lubricationChain drive sprocket Needle bearing lubricationChecking wear on cutting equipment Assembly Fitting the bar and chainFuel Handling FuelTransport and storage Fuel safetyFueling Long-term storageCold engine Starting and StoppingStarting and stopping Warm engineStopping Before use Basic safety rulesWorking Techniques General working instructionsGeneral rules Basic cutting technique GeneralTerms Limbing CuttingFelling direction Tree felling techniqueSafe distance Clearing the trunk and preparing your retreatFelling Directional cutsFelling cut Freeing a trapped tree General adviceFreeing a tree that has fallen badly Cutting trees and branches that are in tensionHow to avoid kickback What is kickback?Cutting the trunk into logs Maintenance Carburetor adjustmentGeneral Checking brake band wear Correctly adjusted carburetorHigh speed jet H Checking the front hand guardChecking the brake trigger Muffler StarterChanging a broken or worn starter cord Changing a broken recoil spring Air filterTensioning the recoil spring Fitting the starterSpark plug Adjustment of the oil pumpWhen making adjustments Lubricating the bar tip sprocketWinter use Air Injection centrifugal cleaningCooling system Heated handlesMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataSaw chain filing and file gauges 050/1,3 mm058/1,5 mm Federal Emission Control Warranty Statement Your Warranty Rights and ObligationsKickback safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Other safety precautionsPage ´z+R1=¶5¨ Page 1150172-95 ´z+R1=¶5¨ ´z+R1=¶5¨
Top Page Image Contents