Husqvarna 1153177-95, 395XPG Cutting equipment, Vibration damping system, Stop switch, Muffler

Page 11

GENERAL SAFETY PRECAUTIONS

Vibration damping system

Your machine is equipped with a vibration damping system that is designed to reduce vibration and make operation easier.

The machine′s vibration damping system reduces the transfer of vibration between the engine unit/cutting equipment and the machine′s handle unit.The body of the chain saw, including the cutting equipment, is insulated from the handles by vibration damping units.

Cutting hardwoods (most broadleaf trees) creates more vibration than cutting softwoods (most conifers). Cutting with cutting equipment that is blunt or faulty (wrong type or badly sharpened) will increase the vibration level.

WARNING! Overexposure to vibration

! can lead to circulatory damage or nerve damage in people who have impaired circulation. Contact your doctor if you experience symptoms of overexposure to vibration. Such symptoms include numbness, loss of feeling, tingling, pricking, pain, loss of strength, changes in skin colour or condition. These symptoms normally appear in the fingers, hands or wrists. These symptoms may be increased in cold temperatures.

Stop switch

Use the stop switch to switch off the engine.

Muffler

The muffler is designed to keep noise levels to a minimum and to direct exhaust fumes away from the user.

WARNING! The exhaust fumes from the

! engine are hot and may contain sparks which can start a fire. Never start the machine indoors or near combustible material!

In areas with a hot, dry climate there is a high risk of fires. These areas are sometimes subject to government rules requiring among other things the muffler must be equipped with an approved type of spark arrestor screen.

CAUTION! The muffler gets very hot during and after use. This also applies during idling. Be aware of the fire hazard, especially when working near flammable substances and/or vapours.

WARNING! Never use a saw without a

! muffler, or with a damaged muffler. A damaged muffler may substantially increase the noise level and the fire hazard. Keep fire fighting equipment handy. If a spark arrestor screen is required in your area, never use the saw without or with a broken spark arrestor screen.

Cutting equipment

This section describes how to choose and maintain your cutting equipment in order to:

•Reduce the risk of kickback.

•Reduce the risk of the saw chain breaking or jumping off the bar.

•Obtain optimal cutting performance.

•Extend the life of cutting equipment.

•Avoid increasing vibration levels.

General rules

•Only use cutting equipment recommended by us! See instructions under the heading Technical data.

English – 11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents 395XP 395XPG Symbols in the operator’s manual KEY to SymbolsSymbols on the machine EPA Contents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?Before using a new chain saw General Safety PrecautionsChain brake and front hand guard Machine′s safety equipmentAlways use common sense Personal protective equipmentGeneral Safety Precautions Right hand guard Throttle lockoutChain catcher Muffler Stop switchCutting equipment Vibration damping systemChain Cutting equipment designed to reduce kickbackBar General information on sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingToo large Increased if the depth gauge setting isAdjustment of depth gauge setting Tensioning the chainChain drive sprocket Lubricating cutting equipmentFilling with chain oil Checking chain lubricationChecking wear on cutting equipment Needle bearing lubricationWorking with the chain AssemblyFitting the bar and chain Fuel Fuel HandlingLong-term storage Fuel safetyFueling Transport and storageWarm engine Starting and StoppingStarting and stopping Cold engineStopping General working instructions Basic safety rulesWorking Techniques Before useGeneral rules Terms Basic cutting techniqueLimbing Clearing the trunk and preparing your retreat Tree felling techniqueSafe distance Felling directionFelling cut Directional cutsFreeing a tree that has fallen badly How to avoid kickbackWhat is kickback? Cutting the trunk into logs Carburetor adjustment MaintenanceChecking brake band wear Fine adjustment of the idling speed TCorrectly adjusted carburetor High speed jet HImmediately Checking the inertia brake releaseMuffler Changing a broken recoil spring StarterChanging a broken or worn starter cord Tensioning the recoil springFitting the starter Air filterSpark plug Lubricating the bar tip sprocketNeedle bearing lubrication Adjustment of the oil pumpAir Injection centrifugal cleaning When making adjustmentsHeated handles Winter useDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical Data063/1,6 mm Saw chain filing and file gauges050/1,3 mm 058/1,5 mmYour Warranty Rights and Obligations Federal Emission Control Warranty StatementEmission Controlwarranty Parts List Other safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Kickback safety precautionsOriginal instructions 1153177-95
Top Page Image Contents