Husqvarna 395XPG, 1153177-95 manual Needle bearing lubrication, Checking wear on cutting equipment

Page 16

GENERAL SAFETY PRECAUTIONS

B Rim sprocket (replaceable)

Regularly check the degree of wear on the drive sprocket. Replace if wear is excessive. Replace the drive sprocket whenever you replace the chain.

Needle bearing lubrication

Both versions of sprockets have a needle bearing on the drive shaft, which has to be greased regularly (once a week). CAUTION! Use only high quality bearing grease or engine oil.

Checking wear on cutting equipment

Check the chain daily for:

•Visible cracks in rivets and links.

•Whether the chain is stiff.

•Whether rivets and links are badly worn.

Replace the saw chain if it exhibits any of the points above.

We recommend you compare the existing chain with a new chain to decide how badly the existing chain is worn.

When the length of the cutting teeth has worn down to only 5/32 inch (4 mm) the chain must be replaced.

Bar

Check regularly:

•Whether there are burrs on the edges of the bar. Remove these with a ﬁle if necessary.

•Whether the groove in the bar has become badly worn. Replace the bar if necessary.

•Whether the tip of the bar is uneven or badly worn. If a hollow forms on the underside of the bar tip this is due to running with a slack chain.

•To prolong the life of the bar you should turn it over daily.

WARNING! Most chain saw accidents

!happen when the chain touches the operator.

Wear personal protective equipment. See instructions under the heading ”Personal protective equipment”.

Do not tackle any job that you feel you are not adequately trained for. See instructions under the headings Personal protective equipment, How to avoid kickback, Cutting equipment and General working instructions.

Avoid situations where there is a risk of kickback. See instructions under the heading Machine′s safety equipment.

Use the recommended protective equipment and check its condition. See instructions under the heading General working instructions.

Check that all the chain saw safety features are working. See instructions under the headings General working instructions and General safety precautions.

16 – English

Image 16

Contents 395XP 395XPG Symbols on the machine KEY to SymbolsSymbols in the operator’s manual EPA Contents Introduction Dear customerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawMachine′s safety equipment Always use common sensePersonal protective equipment Chain brake and front hand guardGeneral Safety Precautions Chain catcher Throttle lockoutRight hand guard Stop switch Cutting equipmentVibration damping system MufﬂerBar Cutting equipment designed to reduce kickbackChain Sharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethIncreased if the depth gauge setting is Adjustment of depth gauge settingTensioning the chain Too largeLubricating cutting equipment Filling with chain oilChecking chain lubrication Chain drive sprocketNeedle bearing lubrication Checking wear on cutting equipmentFitting the bar and chain AssemblyWorking with the chain Fuel Handling FuelFuel safety FuelingTransport and storage Long-term storageStarting and Stopping Starting and stoppingCold engine Warm engineStopping Basic safety rules Working TechniquesBefore use General working instructionsGeneral rules Basic cutting technique TermsLimbing Tree felling technique Safe distanceFelling direction Clearing the trunk and preparing your retreatDirectional cuts Felling cutWhat is kickback? How to avoid kickbackFreeing a tree that has fallen badly Cutting the trunk into logs Maintenance Carburetor adjustmentFine adjustment of the idling speed T Correctly adjusted carburetorHigh speed jet H Checking brake band wearChecking the inertia brake release ImmediatelyMufﬂer Starter Changing a broken or worn starter cordTensioning the recoil spring Changing a broken recoil springAir ﬁlter Spark plugLubricating the bar tip sprocket Fitting the starterAdjustment of the oil pump Air Injection centrifugal cleaningWhen making adjustments Needle bearing lubricationWinter use Heated handlesMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataSaw chain ﬁling and ﬁle gauges 050/1,3 mm058/1,5 mm 063/1,6 mmFederal Emission Control Warranty Statement Your Warranty Rights and ObligationsEmission Controlwarranty Parts List American Standard Safety Precautions Safety precautions for chain saw usersKickback safety precautions Other safety precautionsOriginal instructions 1153177-95