Husqvarna 395XPG Starter, Changing a broken or worn starter cord, Tensioning the recoil spring

Page 34

MAINTENANCE

Starter

WARNING! When the recoil spring is

!wound up in the starter housing it is under tension and can, if handled carelessly, pop out and cause personal injury.

Care must be exercised when replacing the return spring or the starter cord. Wear protective glasses and protective gloves.

Changing a broken or worn starter cord

•Loosen the screws that hold the starter against the crankcase and remove the starter.

•Pull out the cord approx. 30 cm (12 inches) and hook it into the notch in the rim of the pulley. Release the recoil spring by letting the pulley rotate slowly backwards.

•Undo the screw in the centre of the pulley and remove the pulley. Insert and fasten a new starter cord to the pulley. Wind approx. 3 turns of the starter cord onto the pulley. Connect the pulley to the recoil spring so that the end of the spring engages in the pulley. Fit the screw in the center of the pulley. Insert the starter cord through the hole in the starter housing and the starter

handle. Make a secure knot in the end of the starter cord.

Tensioning the recoil spring

•Hook the starter cord in the notch in the pulley and turn the starter pulley about 2 turns clockwise.

Note! Check that the pulley can be turned an additional 1/2 turn when the starter cord is pulled all the way out.

Changing a broken recoil spring

•Lift up the starter pulley. See instructions under the heading Changing a broken or worn starter cord. Remember that the recoil spring is coiled under tension in the starter housing.

•Remove the cassette with the recoil spring from the starter.

•Lubricate the recoil spring with light oil. Fit the cassette with recoil spring in the starter. Fit the starter pulley and tension the recoil spring.

34 – English

Image 34

Contents 395XP 395XPG Symbols on the machine KEY to SymbolsSymbols in the operator’s manual EPA Contents Introduction Dear customerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawPersonal protective equipment Machine′s safety equipmentAlways use common sense Chain brake and front hand guardGeneral Safety Precautions Chain catcher Throttle lockoutRight hand guard Vibration damping system Stop switchCutting equipment MufﬂerBar Cutting equipment designed to reduce kickbackChain Sharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethTensioning the chain Increased if the depth gauge setting isAdjustment of depth gauge setting Too largeChecking chain lubrication Lubricating cutting equipmentFilling with chain oil Chain drive sprocketNeedle bearing lubrication Checking wear on cutting equipmentFitting the bar and chain AssemblyWorking with the chain Fuel Handling FuelTransport and storage Fuel safetyFueling Long-term storageCold engine Starting and StoppingStarting and stopping Warm engineStopping Before use Basic safety rulesWorking Techniques General working instructionsGeneral rules Basic cutting technique TermsLimbing Felling direction Tree felling techniqueSafe distance Clearing the trunk and preparing your retreatDirectional cuts Felling cutWhat is kickback? How to avoid kickbackFreeing a tree that has fallen badly Cutting the trunk into logs Maintenance Carburetor adjustmentHigh speed jet H Fine adjustment of the idling speed TCorrectly adjusted carburetor Checking brake band wearChecking the inertia brake release ImmediatelyMufﬂer Tensioning the recoil spring StarterChanging a broken or worn starter cord Changing a broken recoil springLubricating the bar tip sprocket Air ﬁlterSpark plug Fitting the starterWhen making adjustments Adjustment of the oil pumpAir Injection centrifugal cleaning Needle bearing lubricationWinter use Heated handlesMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical data058/1,5 mm Saw chain ﬁling and ﬁle gauges050/1,3 mm 063/1,6 mmFederal Emission Control Warranty Statement Your Warranty Rights and ObligationsEmission Controlwarranty Parts List Kickback safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Other safety precautionsOriginal instructions 1153177-95