Marantz SR5600 manual Recording AN Analog Source, CH Input, Ht-Eq

ENGLISH	SELECTING ANALOG AUDIO INPUT
	OR DIGITAL AUDIO INPUT
	TUNER	CD	TAPE	CDR/MD
		AUX1	AMP
	TV			MAIN
	VOL.	SLEEP	MUTE	VOL.
		4	5	6
	DISPLAY	MCH-ST	STEREO	7.1CH IN
		7	8	9
	CLEAR	MEMO	A/D	P.SCAN/V-OFF
			0
			CHANNEL/SKIP
	BASS	TREBLE	TUNE/SEARCH

If you have already assigned the digital inputs, you can temporarily select the audio input mode for each input source as following procedures.

RECORDING AN ANALOG SOURCE

In normal operation, the audio or video source selected for listening through the SR5600 is sent to the record outputs.

This means that any program you are watching or listening to may be recorded simply by placing machines connected to the outputs for TAPE OUT,

CD-R/MD OUT, VCR1 OUT, and DSS/VCR2 OUT in the record mode.

To record the input source signal you are currently watching or listening to

1.

	POWER
AV SURROUND RECEIVER SR5600
	TV	VCR1	DSS/VCR2	DVD
1.	TUNER	CD	TAPE	CDR/MD
		AUX1	AMP

1. Switch the video output source to VCR1 by simply pressing the input selector buttons on the remote.

2. Switch the audio input source to CD by simply pressing the input selector buttons on the remote.

3. Now “CD” has been selected as the audio input source and “VCR1” as the video input source.

Notes:

• If you change the input source during recording,

you will record the signals from the newly

selected input source.

• You cannot record the surround effects.

• Digital input signals are only output to the digital

outputs. There is no conversion from digital to

analog .

When connecting CD players and other digital

components, do not connect only the digital

7.1 CH INPUT

The SR5600 is equipped for future expansion t h r o u g h t h e u s e o f M u l t i c h a n n e l S A C D multichannel player or DVD-Audio player.

When this is selected, the input signals connected to the L(front left), R (front right), CENTER, SL (surround left), SR (surround right) and SBL (surround back left) and SBR (surround back right) channels of the 7.1 CH. In jacks are output directly to the front (left and right), center, surround (left and right) and surround back speaker systems as well as the pre-out jacks without passing through the surround circuitry.

In addition, the signal input to the SW (subwoofer) jack is output to the PRE OUT SW (subwoofer) jack.

When 7.1 CH. INPUT is selected, the last video input used remains routed to the Monitor Outputs. This permits simultaneous viewing with video sources

Press the AMP button and press the A/D (0) button.

When this button is pressed, the input mode is switched in the following sequence.

→Digital Auto → Digital → Analog → Digital Auto....

In Digital Auto mode, the types of signals being input to the digital and analog input jacks for the selected input source are detected automatically. If no digital signal is being input, the analog input jacks are selected automatically.

In Digital mode, input is fixed to an assigned digital input terminal.

In analog mode, the analog input jacks are selected. This selecting is temporary, so the result will not be stored in memory.

If you need to change the input mode completely, use INPUT SETUP in OSD menu system. (see page 18)

TV			MAIIN
VOL.	SLEEP	MUTE	VOL.
	OSD	MENU

1. Select the input source to record by turning the INPUT FUNCTION SELECTOR knob on the front panel or simply press the input selector buttons on the remote.

The input source is now selected and you may watch or listen to it as desired.

2. The currently selected input source signal is output to the TAPE OUT, CD-R/MD OUT,

VCR1 OUT, and DSS/VCR2 OUT outputs for

recording.

3. Start recording to the recording component as desired.

Recording the video from one source and the audio from another

You can add the sound from one source to the video of another source to make your own video recordings.

Below is an example of recording the sound from a compact disc player connected to CD IN and the video from a video camera connected to VCR1 to video cassette recorder connected to the DSS/ VCR2 OUT jack.

1.	TV	VCR1	DSS/VCR2	DVD
2.	TUNER	CD	TAPE	CDR/MD
		AUX1	AMP
	TV			MAIN
	VOL.	SLEEP	MUTE	VOL.
	OSD		MENU

terminals, but the analog ones as well.

HT-EQ

AV SURROUND RECEIVER SR5600

SURROUND

DIGITAL

AAC

Press the HT-EQbutton on the front panel to turn on the HT-EQ mode.

The tonal balance of a film soundtrack will be excessively bright and harsh when played back over audio equipment in the home. This is because film soundtracks were designed to be played back in large movie theater environments.

Activating the HT-EQ feature when watching a film made for movie theaters corrects this and restores the correct tonal balance.

The HT-EQ feature is available except in the following modes.

•7.1 CH INPUT

•PURE-DIRECT

•When VIRTUAL is set for the surround mode

2. 1.

AV SURROUND RECEIVER SR5600

4.

SURROUND

DIGITAL

1.

4.

2.

POWER
TV	VCR1	DSS/VCR2	DVD
TUNER	CD	TAPE	CDR/MD
	AUX1	AMP
TV			MAIN
VOL.	SLEEP	MUTE	VOL.
OSD		MENU
	ENTER
SET UP/		MENU OFF
T.TONE
PURE DIRECT	AUTO		DTS
	1	2	3
NIGHT	CSII	EX/ES	VIRTUAL
	4	5	6
DISPLAY	MCH-ST	STEREO	7.1CH IN

7 8 9

CLEAR MEMO A/D P.SCAN/V-OFF

0

CHANNEL/SKIP

28