Marantz SR5600 manual Clearing Stored Preset Stations, Sorting Preset Stations, ← Down

CLEARING STORED PRESET STATIONS

You can remove preset stations from the memory using the following procedure.

2.	3.	SET UP/		MENU OFF
		T.TONE
		PURE DIRECT	AUTO		DTS
			1	2	3
		NIGHT	CSII	EX/ES	VIRTUAL

	2.		7	8	9
			4	5	6
		DISPLAY	MCH-ST	STEREO	7.1CH IN
SURROUND		CLEAR	MEMO	A/D	P.SCAN/V-OFF
DIGITAL
AAC				0
	3.			CHANNEL/SKIP
		BASS	TREBLE	TUNE/SEARCH
			T-MODE	RDS	F.DIRECT
		INPUT/DISC+	AUDIO	SUB-T/ATT	PTY
		CH.SEL			LIP.SYNC

1. Recall the preset number to be cleared with the method described in “Recalling” a preset station.

2. Press the MEMO button on the front panel or press the MEMO button on the remote.

3. The stored preset number blinks in the display for 5 seconds. While blinking, press the CLEAR button on the front panel or the remote.

4. “xx CLEAR” appears on the display to indicate that the specified preset number has been cleared.

Note:

•To clear all stored preset stations, press and hold the CLEAR and the ENTER buttons for two seconds.

SORTING PRESET STATIONS

AV SURROUND RECEIVER SR5600

SURROUND

DIGITAL

AAC

If you have stations memorized, and there is a gap in the sequential order:

I.e. the stations are stored as follows

1)87.1 MHz

2)93.1 MHz

3)94.7 MHz

10) 105.9 MHz

(notice there is no stations programmed for pre sets for 4-9), you can have pre set 10 become pre set 5:

To sort the numbers, press and hold the MEMO and thecursor buttons.

“PRESET SORT” will appear on the display and sorting will be done.

NAME INPUT OF THE PRESET STATION.

This function allows the name of each preset channel to be entered using alphanumeric characters.

Before name inputting, you need to store preset stations with the preset memory operation.

4.5. 2. 5. 6.

AV SURROUND RECEIVER SR5600

SURROUND

DIGITAL

AAC

5.	OSD		MENU
		ENTER
5.	SET UP/		MENU OFF
	T.TONE
	PURE DIRECT	AUTO		DTS
		1	2	3
2. 5. 6.	NIGHT	CSII	EX/ES	VIRTUAL
		7	8	9
		4	5	6
	DISPLAY	MCH-ST	STEREO	7.1CH IN
	CLEAR	MEMO	A/D	P.SCAN/V-OFF
			0
			CHANNEL/SKIP
5.	BASS	TREBLE	TUNE/SEARCH
		T-MODE RDS F.DIRECT
4.	INPUT/DISC+	AUDIO	SUB-T/ATT	PTY
	CH.SEL			LIP.SYNC

1.	Recall the preset number to be inputted name
	with the method described in “Recalling” a
2.	preset station.
	Press the MEMO button on the front panel or
	press the MEMO button on the remote for
3.	more than 3 seconds.
	The left most column of the station name
	indicator flashes, indicating the character
4.	entry ready status.
	When you press the or cursor buttons on

the front panel or the 5 / 6 buttons on the remote, alphabetic and numeric characters will be displayed in the following order:

A → B → C ... Z → 1 → 2 → 3 ..... 0 → – → +

→/ → (Blank) → A UP →

←DOWN

5.After selecting the first character to be entered, press the MEMO or ENTER buttons, press the MEMO button on the remote.

The entry in this column is fixed and the next column starts to flash. Fill the next column the same way.

To move back and forth between the characters, press the/cursor buttons or press 4or ¢buttons on the remote.

Note:

•Unused columns should be filled by entering blanks.

6.To save the name, press the MEMO button on the front panel or remote for more than 2 seconds.

Ten keypad Press, press again, press again, etc.

1A → B → C → 1 → A

2D → E → F → 2 → D

3G → H → I → 3 → G

4J → K → L → 4 → J

5M → N → O → 5 → M

6P → Q → R → 6 → P

7S → T → U → 7 → S

8V → W → X → 8 → V

9Y → Z → space → 9 → Y

0– → + → / → 0

ENGLISH

31