Husqvarna 385XP manual Tensioning the chain, General advice on adjusting depth gauge setting

Page 13

GENERAL SAFETY PRECAUTIONS

General advice on adjusting depth gauge setting

•When you sharpen the cutting tooth (A) the depth gauge setting (C) will decrease. To maintain optimal cutting performance the depth gauge (B) has to be filed down to achieve the recommended depth gauge setting. See instructions under the heading Technical data to find the correct depth gauge setting for your particular chain.

WARNING! The risk of kickback is increased

!if the depth gauge setting is too large!

Adjustment of depth gauge setting

•The cutting teeth should be newly sharpened before adjusting the depth gauge setting. We recommend that you adjust the depth gauge setting every third time you sharpen the cutting teeth. NOTE! This recommendation assumes that the length of the cutting teeth is not reduced excessively.

•You will need a flat file and a depth gauge tool. We recommend that you use our depth gauge tool to acheive the correct depth gauge setting and bevel for the depth gauge.

•Place the depth gauge tool over the chain. Detailed information regarding the use of the depth gauge tool, will be found on the package for the depth gauge tool. Use the flat file to file off the tip of the depth gauge that protrudes through the depth gauge tool. The depth gauge setting is correct when you no longer feel resistance as you draw the file along the depth gauge tool.

Tensioning the chain

WARNING! A slack chain may jump off and

!cause serious or even fatal injury.

The more you use a chain the longer it becomes. It is therefore important to adjust the chain regularly to take up the slack.

Check the chain tension every time you refuel. NOTE! A new chain has a running-in period during which you should check the tension more frequently.

Tension the chain as tightly as possible, but not so tight that you cannot pull it round freely by hand.

•Undo the bar nuts that hold the clutch cover/chain brake. Use the combination spanner. Then tighten the bar nuts by hand as tight as you can.

•Raise the tip of the bar and stretch the chain by tightening the chain tensioning screw using the combination spanner. Tighten the chain until it does not sag from the underside of the bar.

•Use the combination spanner to tighten the bar nuts while lifting the tip of the bar at the same time. Check that you can pull the chain round freely by hand and that it does not sag from the underside of the bar.

The position of the chain tensioning screw on our chain saws varies from model to model. See instructions under the heading What is what? to find out where it is on your model.

English – 13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents 385XP 390XP Symbols on the machine KEY to SymbolsSymbols in the operator’s manual Contents Dear Customer IntroductionWhat is what on the chain saw? What is WHAT?Before using a new chain saw General Safety PrecautionsAlways use common sense Personal protective equipment Machine′s safety equipmentChain brake and front hand guard General Safety Precautions Chain catcher Throttle lockRight hand guard Cutting equipment Stop switchVibration damping system MufflerCutting equipment designed to reduce kickback General rulesBar ChainGeneral information on sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingSharpening cutting teeth Adjustment of depth gauge setting General advice on adjusting depth gauge settingIf the depth gauge setting is too large Tensioning the chainChain oil Lubricating cutting equipmentFilling with chain oil Checking chain lubricationNeedle bearing lubrication Chain drive sprocketChecking wear on cutting equipment Fitting the bar and chain AssemblyFitting a spike bumper Working with the chainFuel Fuel HandlingFuelling Fuel safetyTransport and storage Long-term storageStarting and stopping Starting and StoppingCold engine Warm engineStopping Working Techniques Basic safety rulesBefore use General working instructionsAlways use a fast cutting speed, i.e. full throttle General Basic cutting techniqueTerms Cutting LimbingSafe distance Tree felling techniqueFelling direction Clearing the trunk and preparing your retreatDirectional cuts FellingFelling cut Freeing a tree that has fallen badly General adviceFreeing a trapped tree Cutting trees and branches that are in tensionWhat is kickback? How to avoid kickbackCutting the trunk into logs Carburettor adjustment MaintenanceGeneral Carburettor with movement limitersCorrectly adjusted carburettor Fine adjustment of the idle speed TCarburettor without movement limiters Low speed jet LChecking brake band wear Checking the front hand guard When the bar hits the stump the brake should be appliedChecking the inertia brake release Checking the brake triggerMuffler Changing a broken or worn starter cord StarterTensioning the recoil spring Changing a broken recoil springSpark plug Air filterLubricating the bar tip sprocket Fitting the starterAir Injection centrifugal cleaning Adjustment of the oil pumpNeedle bearing lubrication Cooling systemHeated handles Temperature 0C or colderElectrical carburettor heating 385XPG, 390XPGDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical DataSaw chain filing and file gauges Bar and chain combinationsApplies to Europe only EC-declaration of conformityEN ISO 12100-22003, Cispr 121997, ISO ´z+R16¶6a¨ Page 1150172-26 ´z+R16¶6a¨ ´z+R16¶6a¨

385XP specifications

The Husqvarna 385XP is a powerful and versatile chainsaw, designed to meet the demands of professional loggers and landowners alike. Known for its exceptional performance and reliability, this model is engineered for heavy-duty tasks, making it a popular choice among forestry professionals and those requiring robust cutting tools.

One of the standout features of the 385XP is its impressive engine performance. The chainsaw is equipped with a 70.7 cc, 4.2 horsepower X-Torq engine, which not only delivers high power output but also ensures lower fuel consumption and reduced emissions, making it environmentally friendly without sacrificing performance. The innovative X-Torq technology allows for optimal combustion, enabling the chainsaw to run smoother and more efficiently.

The design of the Husqvarna 385XP focuses on user comfort and control. It features an ergonomic handle that reduces vibrations, enhancing the operator's comfort during extended use. The chainsaw's anti-vibration system minimizes the impact of vibrations on the user's hands, allowing for longer periods of operation without fatigue. This is crucial for professionals who spend hours in the field.

Another important technological aspect of the 385XP is its easily adjustable chain tensioning system, which simplifies adjustments and maintenance. The side-mounted chain tensioner allows users to make quick changes without the need for additional tools, ensuring that they can focus on the job at hand rather than fussing with equipment.

The 385XP is equipped with a high-quality cutting bar and chain, designed for durability and efficiency. The chainsaw features a 20-inch bar that provides ample cutting capacity, allowing for precise cuts in a variety of wood types. Its sharp chain ensures clean cuts with minimal kickback, enhancing safety and effectiveness when tackling larger logs or dense trees.

Another notable feature is the Air Injection system, which utilizes centrifugal force to remove larger dust and debris particles before they reach the air filter. This prolongs the filter’s life and decreases maintenance requirements, allowing users to spend more time working rather than cleaning.

In conclusion, the Husqvarna 385XP is a reliable chainsaw that combines power, efficiency, and user comfort. Its cutting-edge technologies, durable construction, and ease of use make it an ideal choice for professionals in the forestry industry and skilled homeowners alike.
Top Page Image Contents