Husqvarna 385XP manual Carburettor without movement limiters, Low speed jet L, High speed jet H

Page 30

MAINTENANCE

Low speed jet L

Turn the low speed jet L clockwise until it stops. If the engine accelerates poorly or idles unevenly, turn the low speed jet L anticlockwise until good acceleration and idling are achieved.

CAUTION! If the chain rotates while idling the T-screw must be turned anti-clockwise until the chain stops.

Fine adjustment of the idle speed T

Adjust the idle speed with the T-screw. If it is necessary to re- adjust, turn the T-screw clockwise while the engine is running, until the chain starts to rotate. Then turn anti-clockwise until the chain stops. When the idle speed is correctly adjusted the engine should run smoothly in every position and the engine speed should be safely below the speed at which the chain starts to rotate.

WARNING! Contact your servicing dealer, if

!the idle speed setting cannot be adjusted so that the chain stops. Do not use the chain saw until it has been properly adjusted or repaired.

High speed jet H

At the factory the engine is adjusted at sea level. When working at a high altitude or in different weather conditions, temperatures and atmospheric humidity, it may be necessary to make minor adjustments to the high speed jet.

CAUTION! If the high speed jet is screwed in too far, it may damage the piston/cylinder.

When test run at the factory, the high speed jet is set so that the engine satisfies the applicable legal requirements at the same time as achieving maximum performance. The carburettor’s high speed jet is then locked using a limiter cap in the fully screwed out position. The limiter cap limits the potential to adjust the high speed jet to at most half a turn.

CAUTION! There is an integrated speed governor in the ignition system that limits the maximum speed to 13000 rpm. The maximum speed will not exceed 13000 rpm when the high speed jet is adjusted (screwed in). When the speed governor is activated, you will get the same sound experience as when the chain saw 4-cycles.

To adjust the carburettor correctly you should contact a mechanic with access to a rev counter.

CAUTION! As the spark is cut off, the rev counter does not show speeds higher than 13000 rpm.

Correctly adjusted carburettor

When the carburettor is correctly adjusted the machine accelerates without hesitation and 4-cycles a little at full throttle. It is also important that the chain does not rotate at idle. If the L-jet is set too lean it may cause starting difficulties and poor acceleration. If the H-jet is set too lean the machine will have less power, poor acceleration and could suffer damage to the engine.

Carburettor without movement limiters

Function, Basic settings, Fine adjustment

WARNING! Do not start the chain saw unless

!the bar, chain and clutch cover (chain brake) are fitted, otherwise the clutch may come loose and cause personal injury.

Function

•The carburettor governs the engine’s speed via the throttle control. Air and fuel are mixed in the carburettor. The air/fuel mixture is adjustable. Correct adjustment is essential to get the best performance from the machine.

•Adjusting the carburettor means that the engine is adapted to local operating conditions, e.g. climate, altitude, petrol and the type of 2-stroke oil.

•The carburettor has three adjustment controls:

-L = Low speed jet

-H = High speed jet

-T = Idle adjustment screw

TH

L

•The T-screw regulates the throttle setting at idle speed. If the T-screw is turned clockwise this gives a higher idle speed; turning it anti-clockwise gives a lower idle speed.

Basic settings and running in

The basic carburettor settings are adjusted during testing at the factory. The basic settings are H = 1 turn and L = 1 turn. To provide the engine’s components with good initial lubrication (during running in) the carburettor should be set for a richer fuel mixture for the first 3-4 hours that the chain saw is in use. To do this, adjust the fast idle speed to 600-700 rpm below the recommended maximum fast idle speed.

If you are unable to check the fast idle speed using a tachometer the H-jet should not be set for a leaner mixture than given in the basic settings. The recommended maximum fast idle speed must not be exceeded. CAUTION! If the chain rotates while idling the T-screw must be turned anti- clockwise until the chain stops.

30 – English

Page 29 Page 31
Image 30
Page 29 Page 31
Contents 385XP 390XP KEY to Symbols Symbols on the machineSymbols in the operator’s manual Contents Introduction Dear CustomerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawAlways use common sense Machine′s safety equipment Personal protective equipmentChain brake and front hand guard General Safety Precautions Throttle lock Chain catcherRight hand guard Vibration damping system Stop switchCutting equipment MufflerBar General rulesCutting equipment designed to reduce kickback ChainSharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethSharpening cutting teeth If the depth gauge setting is too large General advice on adjusting depth gauge settingAdjustment of depth gauge setting Tensioning the chainFilling with chain oil Lubricating cutting equipmentChain oil Checking chain lubricationChain drive sprocket Needle bearing lubricationChecking wear on cutting equipment Fitting a spike bumper AssemblyFitting the bar and chain Working with the chainFuel Handling FuelTransport and storage Fuel safetyFuelling Long-term storageCold engine Starting and StoppingStarting and stopping Warm engineStopping Before use Basic safety rulesWorking Techniques General working instructionsAlways use a fast cutting speed, i.e. full throttle Basic cutting technique GeneralTerms Limbing CuttingFelling direction Tree felling techniqueSafe distance Clearing the trunk and preparing your retreatFelling Directional cutsFelling cut Freeing a trapped tree General adviceFreeing a tree that has fallen badly Cutting trees and branches that are in tensionHow to avoid kickback What is kickback?Cutting the trunk into logs General MaintenanceCarburettor adjustment Carburettor with movement limitersCarburettor without movement limiters Fine adjustment of the idle speed TCorrectly adjusted carburettor Low speed jet LChecking brake band wear Checking the inertia brake release When the bar hits the stump the brake should be appliedChecking the front hand guard Checking the brake triggerMuffler Tensioning the recoil spring StarterChanging a broken or worn starter cord Changing a broken recoil springLubricating the bar tip sprocket Air filterSpark plug Fitting the starterNeedle bearing lubrication Adjustment of the oil pumpAir Injection centrifugal cleaning Cooling systemElectrical carburettor heating Temperature 0C or colderHeated handles 385XPG, 390XPGMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataBar and chain combinations Saw chain filing and file gaugesEC-declaration of conformity Applies to Europe onlyEN ISO 12100-22003, Cispr 121997, ISO ´z+R16¶6a¨ Page 1150172-26 ´z+R16¶6a¨ ´z+R16¶6a¨

385XP specifications

The Husqvarna 385XP is a powerful and versatile chainsaw, designed to meet the demands of professional loggers and landowners alike. Known for its exceptional performance and reliability, this model is engineered for heavy-duty tasks, making it a popular choice among forestry professionals and those requiring robust cutting tools.

One of the standout features of the 385XP is its impressive engine performance. The chainsaw is equipped with a 70.7 cc, 4.2 horsepower X-Torq engine, which not only delivers high power output but also ensures lower fuel consumption and reduced emissions, making it environmentally friendly without sacrificing performance. The innovative X-Torq technology allows for optimal combustion, enabling the chainsaw to run smoother and more efficiently.

The design of the Husqvarna 385XP focuses on user comfort and control. It features an ergonomic handle that reduces vibrations, enhancing the operator's comfort during extended use. The chainsaw's anti-vibration system minimizes the impact of vibrations on the user's hands, allowing for longer periods of operation without fatigue. This is crucial for professionals who spend hours in the field.

Another important technological aspect of the 385XP is its easily adjustable chain tensioning system, which simplifies adjustments and maintenance. The side-mounted chain tensioner allows users to make quick changes without the need for additional tools, ensuring that they can focus on the job at hand rather than fussing with equipment.

The 385XP is equipped with a high-quality cutting bar and chain, designed for durability and efficiency. The chainsaw features a 20-inch bar that provides ample cutting capacity, allowing for precise cuts in a variety of wood types. Its sharp chain ensures clean cuts with minimal kickback, enhancing safety and effectiveness when tackling larger logs or dense trees.

Another notable feature is the Air Injection system, which utilizes centrifugal force to remove larger dust and debris particles before they reach the air filter. This prolongs the filter’s life and decreases maintenance requirements, allowing users to spend more time working rather than cleaning.

In conclusion, the Husqvarna 385XP is a reliable chainsaw that combines power, efficiency, and user comfort. Its cutting-edge technologies, durable construction, and ease of use make it an ideal choice for professionals in the forestry industry and skilled homeowners alike.
Top Page Image Contents