Husqvarna 385XP Maintenance, General, Carburettor adjustment, Carburettor with movement limiters

Page 29

MAINTENANCE

General

The user must only carry out the maintenance and service work described in this manual.

IMPORTANT! Any maintenance other than that described in this manual must be carried out by your servicing dealer (retailer).

Carburettor adjustment

The carburettor can be designed in different ways, depending on existing environmental and emissions legislation. Some chain saws are equipped with movement limiters on the carburettor’s adjuster screws. These limit the adjustment possibilities to a maximum of a 1/2 turn.

H

L

1/2

1/2

When your chain saw is equipped with a carburettor that features movement limiters, the carburettor should be adjusted according to the instructions under the heading Carburettor with movement limiters.

When your chain saw is equipped with a carburettor that does not feature movement limiters, the carburettor should be adjusted according to the instructions under the heading Carburettor without movement limiters.

H

L

Contact your servicing dealer (retailer) if you are uncertain of which type of carburettor your chain saw is equipped with.

Carburettor with movement limiters

H

L

1/2

1/2

Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions.

Function, Basic settings, Fine adjustment

WARNING! Do not start the chain saw unless

!the bar, chain and clutch cover (chain brake) are fitted, otherwise the clutch may come loose and cause personal injury.

Function

•The carburettor governs the engine’s speed via the throttle control. Air and fuel are mixed in the carburettor. The air/fuel mixture is adjustable. Correct adjustment is

essential to get the best performance from the machine.

•Adjusting the carburettor means that the engine is adapted to local operating conditions, e.g. climate, altitude, petrol and the type of 2-stroke oil.

•The carburettor has three adjustment controls:

-L = Low speed jet

-H = High speed jet

-T = Idle adjustment screw

TH

L

•The L and H-jets are used to adjust the supply of fuel to match the rate that air is admitted, which is controlled with the throttle. If they are screwed clockwise the air/fuel ratio becomes leaner (less fuel) and if they are turned anti-clockwise the ratio becomes richer (more fuel). A lean mixture gives a higher engine speed and a rich mixture gives a lower engine speed.

•The T-screw regulates the throttle setting at idle speed. If the T-screw is turned clockwise this gives a higher idle speed; turning it anti-clockwise gives a lower idle speed.

Basic settings and running in

The basic carburettor settings are adjusted during testing at the factory. Avoid running at a too high speed during the first 10 hours.

CAUTION! If the chain rotates while idling the T-screw must be turned anti-clockwise until the chain stops.

Rec. idle speed: 2700 rpm

WARNING! Contact your servicing dealer, if

!the idle speed setting cannot be adjusted so that the chain stops. Do not use the chain saw until it has been properly adjusted or repaired.

Fine adjustment

When the machine has been ”run-in” the carburettor should be finely adjusted. The fine adjustment should be carried out by a qualified person. First adjust the L-jet, then the idling screw T and then the H-jet.

Changing the type of fuel

Fine tuning may be required if the chain saw, after changing the type of fuel, performs differently with regard to starting, acceleration, maximum speed, etc.

Conditions

•Before any adjustments are made the air filter should be clean and the cylinder cover fitted. Adjusting the carburettor while a dirty air filter is in use will result in a leaner mixture next time the filter is cleaned. This can give rise to serious engine damage.

•Do not attempt to adjust the L and H jets beyond either stop as this could cause damage.

•Now start the machine according to the starting instructions and let it warm up for 10 minutes. CAUTION!

If the chain rotates while idling the T-screw must be turned anti-clockwise until the chain stops.

•Place the machine on a flat surface so that the bar points away from you and so that the bar and chain do not come into contact with the surface or other objects.

English – 29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents 385XP 390XP Symbols in the operator’s manual KEY to SymbolsSymbols on the machine Contents Dear Customer IntroductionWhat is what on the chain saw? What is WHAT?Always use common sense General Safety PrecautionsBefore using a new chain saw Chain brake and front hand guard Machine′s safety equipmentPersonal protective equipment General Safety Precautions Right hand guard Throttle lockChain catcher Cutting equipment Stop switchVibration damping system MufflerCutting equipment designed to reduce kickback General rulesBar ChainSharpening cutting teeth Sharpening your chain and adjusting depth gauge settingGeneral information on sharpening cutting teeth Adjustment of depth gauge setting General advice on adjusting depth gauge settingIf the depth gauge setting is too large Tensioning the chainChain oil Lubricating cutting equipmentFilling with chain oil Checking chain lubricationChecking wear on cutting equipment Chain drive sprocketNeedle bearing lubrication Fitting the bar and chain AssemblyFitting a spike bumper Working with the chainFuel Fuel HandlingFuelling Fuel safetyTransport and storage Long-term storageStarting and stopping Starting and StoppingCold engine Warm engineStopping Working Techniques Basic safety rulesBefore use General working instructionsAlways use a fast cutting speed, i.e. full throttle Terms Basic cutting techniqueGeneral Cutting LimbingSafe distance Tree felling techniqueFelling direction Clearing the trunk and preparing your retreatFelling cut FellingDirectional cuts Freeing a tree that has fallen badly General adviceFreeing a trapped tree Cutting trees and branches that are in tensionCutting the trunk into logs How to avoid kickbackWhat is kickback? Carburettor adjustment MaintenanceGeneral Carburettor with movement limitersCorrectly adjusted carburettor Fine adjustment of the idle speed TCarburettor without movement limiters Low speed jet LChecking brake band wear Checking the front hand guard When the bar hits the stump the brake should be appliedChecking the inertia brake release Checking the brake triggerMuffler Changing a broken or worn starter cord StarterTensioning the recoil spring Changing a broken recoil springSpark plug Air filterLubricating the bar tip sprocket Fitting the starterAir Injection centrifugal cleaning Adjustment of the oil pumpNeedle bearing lubrication Cooling systemHeated handles Temperature 0C or colderElectrical carburettor heating 385XPG, 390XPGDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical DataSaw chain filing and file gauges Bar and chain combinationsEN ISO 12100-22003, Cispr 121997, ISO EC-declaration of conformityApplies to Europe only ´z+R16¶6a¨ Page 1150172-26 ´z+R16¶6a¨ ´z+R16¶6a¨

385XP specifications

The Husqvarna 385XP is a powerful and versatile chainsaw, designed to meet the demands of professional loggers and landowners alike. Known for its exceptional performance and reliability, this model is engineered for heavy-duty tasks, making it a popular choice among forestry professionals and those requiring robust cutting tools.

One of the standout features of the 385XP is its impressive engine performance. The chainsaw is equipped with a 70.7 cc, 4.2 horsepower X-Torq engine, which not only delivers high power output but also ensures lower fuel consumption and reduced emissions, making it environmentally friendly without sacrificing performance. The innovative X-Torq technology allows for optimal combustion, enabling the chainsaw to run smoother and more efficiently.

The design of the Husqvarna 385XP focuses on user comfort and control. It features an ergonomic handle that reduces vibrations, enhancing the operator's comfort during extended use. The chainsaw's anti-vibration system minimizes the impact of vibrations on the user's hands, allowing for longer periods of operation without fatigue. This is crucial for professionals who spend hours in the field.

Another important technological aspect of the 385XP is its easily adjustable chain tensioning system, which simplifies adjustments and maintenance. The side-mounted chain tensioner allows users to make quick changes without the need for additional tools, ensuring that they can focus on the job at hand rather than fussing with equipment.

The 385XP is equipped with a high-quality cutting bar and chain, designed for durability and efficiency. The chainsaw features a 20-inch bar that provides ample cutting capacity, allowing for precise cuts in a variety of wood types. Its sharp chain ensures clean cuts with minimal kickback, enhancing safety and effectiveness when tackling larger logs or dense trees.

Another notable feature is the Air Injection system, which utilizes centrifugal force to remove larger dust and debris particles before they reach the air filter. This prolongs the filter’s life and decreases maintenance requirements, allowing users to spend more time working rather than cleaning.

In conclusion, the Husqvarna 385XP is a reliable chainsaw that combines power, efficiency, and user comfort. Its cutting-edge technologies, durable construction, and ease of use make it an ideal choice for professionals in the forestry industry and skilled homeowners alike.
Top Page Image Contents