Husqvarna 357XP/XPG, 359G E-tech, 359/G Limbing, Logs are lying together. Such, Or fatal injury

Page 25

WORKING TECHNIQUES

4 Is there a risk of kickback?

5Do the conditions and surrounding terrain affect how safely you can stand and move about?

Two factors decide whether the chain will jam or the object that you are cutting will split: the first is how the object is supported before and after cutting, and the second is whether it is in tension.

In most cases you can avoid these problems by cutting in two stages; from the top and from the bottom.You need to support the object so that it will not trap the chain or split during cutting.

IMPORTANT! If the chain jams in the cut: stop the engine! Don’t try to pull the chain saw free. If you do you may be injured by the chain when the chain saw suddenly breaks free. Use a lever to open up the cut and free the chain saw.

The following instructions describe how to handle the common situations you are likely to encounter when using a chain saw.

Limbing

When limbing thick branches you should use the same approach as for cutting.

Cut difficult branches piece by piece.

1

2

 

 

3

Cutting

 

!

WARNING! Never attempt to cut logs

while they are in a pile or when a couple

 

of logs are lying together. Such

 

procedures drastically increase the risk

 

of kickback which can result in a serious

 

or fatal injury.

If you have a pile of logs, each log you attempt to cut should be removed from the pile, placed on a saw horse or runners and cut individually.

Remove the cut pieces from the cutting area. By leaving them in the cutting area, you increase the risk for

inadvertently getting a kickback, as well as increasing the risk of losing your balance while working.

The log is lying on the ground. There is little risk of the chain jamming or the object splitting. However there is a risk that the chain will touch the ground when you finish the cut.

Cut all the way through the log from above. Avoid letting the chain touch the ground as you finish the cut. Maintain full throttle but be prepared for what might happen.

If it is possible (can you turn the log?) stop cutting about 2/3 of the way through the log.

Turn the log and finish the cut from the opposite side.

The log is supported at one end. There is a high risk that it will split.

Start by cutting from below (about 1/3 of the way through).

Finish by cutting from above so that the two cuts meet.

The log is supported at both ends. There is a high risk that the chain will jam.

Start by cutting from above (about 1/3 of the way through).

English – 25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Operator’s manual Symbols on the machine KEY to SymbolsSymbols in the operator’s manual EPA Contents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?Before using a new chain saw General Safety PrecautionsAlways use common sense Machine′s safety equipmentPersonal protective equipment Chain brake and front hand guardGeneral Safety Precautions Chain catcher Throttle lockoutRight hand guard Cutting equipment Stop switchVibration damping system MufflerBar Cutting equipment designed to reduce kickbackChain General information on sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingIncreases the risk of kickback Sharpening cutting teethTensioning the chain Lubricating cutting equipment Needle bearing lubrication Chain drive sprocketChecking wear on cutting equipment Fitting the bar and chain AssemblyWorking with the chain Fuel Fuel HandlingFueling Fuel safetyTransport and storage Long-term storageStarting and stopping Starting and StoppingCold engine Warm engineStopping Working Techniques Basic safety rulesBefore use General working instructionsCleaning Clutch cover causing the chain toJam. Always stop the engine before Terms Basic cutting techniqueLogs are lying together. Such LimbingOr fatal injury Safe distance Tree felling techniqueFelling direction Clearing the trunk and preparing your retreatYour saw Training we advise you not to fell treesDirectional cuts Felling cutFreeing a tree that has fallen badly General adviceFreeing a trapped tree Cutting trees and branches that are in tensionWhat is kickback? How to avoid kickbackCarburetor adjustment MaintenanceGeneral High speed jet H Correctly adjusted carburetorChecking the brake trigger Muffler Changing a broken or worn starter cord Wound up in the starter housing it isTensioning the recoil spring Changing a broken recoil springSpark plug Air filterFitting the starter When making adjustments Adjustment of the oil pumpLubricating the bar tip sprocket Needle bearing lubricationTemperature 0C 32F or colder Air Injection centrifugal cleaningWinter use Heated handlesDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data 050 Bar and chain combinations058 Saw chain filing and file gauges Your Warranty Rights and Obligations Federal Emission Control Warranty StatementSafety precautions for chain saw users American Standard Safety PrecautionsKickback safety precautions Other safety precautionsOriginal instructions 1153179-95

1153179-95, 359/G, 359G E-tech, 357XP E-tech, 357XP/XPG specifications

The Husqvarna 357XPG E-tech and its counterparts, the 357XP/XPG, 357XP E-tech, and 359G E-tech, are noteworthy chainsaws designed for both professionals and enthusiasts who demand reliability and performance. These models encompass advanced technologies that enhance their functionality, making them suitable for a variety of cutting tasks.

One of the standout features of the 357XPG and its siblings is the E-tech engine technology. This system is designed to provide high performance while minimizing environmental impact. The E-tech engines are known for delivering efficient fuel consumption and lower emissions, making them compliant with stringent regulations and eco-friendly.

The chainsaw is equipped with an air injection system that pre-cleans the intake air, reducing the amount of debris that enters the engine. This results in longer air filter life and reduces maintenance, allowing users to focus more on their cutting tasks rather than frequent cleanings.

The 357XPG model is also equipped with a heated handle, a valuable feature for those working in colder climates. This ergonomic design ensures comfort and usability, reducing user fatigue during extended periods of operation. The rubberized clutch cover and handle reduce vibration, allowing for smoother handling and less strain on the operator.

In addition, the chainsaws are designed with a lightweight body, which enhances maneuverability. The magnesium and composite materials used in construction contribute to the overall durability without adding excessive weight. This combination makes it easy for users to handle the saw for both horizontal and vertical cuts.

The 357XP/XPG and 359G E-tech series include advanced bar and chain systems, providing superior cutting performance. The chains are designed for fast and efficient cutting, enabling users to tackle tough wood with minimal effort. The automatic oiler ensures that the bar and chain receive adequate lubrication, reducing wear and enhancing longevity.

For ease of use, the chainsaws are equipped with a tool-less chain tensioning system, allowing users to make quick adjustments without the need for additional tools. This feature highlights the user-friendly design that Husqvarna emphasizes in its products.

In summary, the Husqvarna 357XPG E-tech, 357XP, and 359G models stand out due to their advanced engine technologies, ergonomic features, lightweight construction, and practical design elements. These chainsaws offer a blend of performance, ease of use, and environmental responsibility, making them ideal tools for both professional lumberjacks and homeowners looking to accomplish tough cutting tasks efficiently.
Top Page Image Contents