Husqvarna 357XP/XPG, 359G E-tech, 357XP E-tech High speed jet H, Correctly adjusted carburetor

Page 31

MAINTENANCE

!

WARNING! Contact your servicing

dealer, if the idle speed setting cannot be

 

 

adjusted so that the chain stops at idle.

 

Do not use the chain saw until it has

 

been properly adjusted or repaired.

High speed jet H

At the factory the engine is adjusted at sea level. When working at a high altitude or in different weather conditions, temperatures and atmospheric humidity, it may be necessary to make minor adjustments to the high speed jet.

CAUTION! If the high speed jet is screwed in too far, it may damage the piston/cylinder.

When test run at the factory, the high speed jet is set so that the engine satisfies the applicable legal requirements at the same time as achieving maximum performance. The carburetor’s high speed jet is then locked using a limiter cap in the fully screwed out position. The limiter cap limits the potential to adjust the high speed jet to at most half a turn.

Correctly adjusted carburetor

When the carburetor is correctly adjusted the machine accelerates without hesitation and the machine 4-cycles a little at max. speed. It is also important that the chain does not rotate at idle. If the L-jet is set too lean it may cause starting difficulties and poor acceleration. If the H-jet is set too lean the machine will have less power, poor acceleration and could suffer damage to the engine.

Checking, maintaining and servicing chain saw safety equipment

Note! All servicing and repair work on the machine requires special training. This is especially true of the machines safety equipment. If your machine fails any of the checks described below we recommend you to contact our servicing dealer.

Chain brake and front hand guard

Checking brake band wear

Brush off any wood dust, resin and dirt from the chain brake and clutch drum. Dirt and wear can impair operation of the brake.

Regularly check that the brake band is at least 0.024 inch (0.6 mm) thick at its thinnest point.

Checking the front hand guard

Make sure the front hand guard is not damaged and that there are no visible defects such as cracks.

Move the front hand guard forwards and back to make sure it moves freely and that it is securely anchored to the clutch cover.

Checking the inertia brake release

With the engine turned off, hold the chain saw over a stump or other firm object. Let go of the front handle so that the bar drops towards the stump as the chain saw rotates around the rear handle.

When the bar hits the stump the brake should be applied.

English 31

Image 31
Contents Operator’s manual Symbols on the machine KEY to SymbolsSymbols in the operator’s manual EPA Contents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?Before using a new chain saw General Safety PrecautionsChain brake and front hand guard Machine′s safety equipmentAlways use common sense Personal protective equipmentGeneral Safety Precautions Chain catcher Throttle lockoutRight hand guard Muffler Stop switchCutting equipment Vibration damping systemBar Cutting equipment designed to reduce kickbackChain Sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingGeneral information on sharpening cutting teeth Increases the risk of kickbackTensioning the chain Lubricating cutting equipment Needle bearing lubrication Chain drive sprocketChecking wear on cutting equipment Fitting the bar and chain AssemblyWorking with the chain Fuel Fuel HandlingLong-term storage Fuel safetyFueling Transport and storageWarm engine Starting and StoppingStarting and stopping Cold engineStopping General working instructions Basic safety rulesWorking Techniques Before useCleaning Clutch cover causing the chain toJam. Always stop the engine before Terms Basic cutting techniqueLogs are lying together. Such LimbingOr fatal injury Clearing the trunk and preparing your retreat Tree felling techniqueSafe distance Felling directionFelling cut Training we advise you not to fell treesYour saw Directional cutsCutting trees and branches that are in tension General adviceFreeing a tree that has fallen badly Freeing a trapped treeWhat is kickback? How to avoid kickbackCarburetor adjustment MaintenanceGeneral High speed jet H Correctly adjusted carburetorChecking the brake trigger Muffler Changing a broken recoil spring Wound up in the starter housing it isChanging a broken or worn starter cord Tensioning the recoil springSpark plug Air filterFitting the starter Needle bearing lubrication Adjustment of the oil pumpWhen making adjustments Lubricating the bar tip sprocketHeated handles Air Injection centrifugal cleaningTemperature 0C 32F or colder Winter useDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data 050 Bar and chain combinations058 Saw chain filing and file gauges Your Warranty Rights and Obligations Federal Emission Control Warranty StatementOther safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Kickback safety precautionsOriginal instructions 1153179-95

1153179-95, 359/G, 359G E-tech, 357XP E-tech, 357XP/XPG specifications

The Husqvarna 357XPG E-tech and its counterparts, the 357XP/XPG, 357XP E-tech, and 359G E-tech, are noteworthy chainsaws designed for both professionals and enthusiasts who demand reliability and performance. These models encompass advanced technologies that enhance their functionality, making them suitable for a variety of cutting tasks.

One of the standout features of the 357XPG and its siblings is the E-tech engine technology. This system is designed to provide high performance while minimizing environmental impact. The E-tech engines are known for delivering efficient fuel consumption and lower emissions, making them compliant with stringent regulations and eco-friendly.

The chainsaw is equipped with an air injection system that pre-cleans the intake air, reducing the amount of debris that enters the engine. This results in longer air filter life and reduces maintenance, allowing users to focus more on their cutting tasks rather than frequent cleanings.

The 357XPG model is also equipped with a heated handle, a valuable feature for those working in colder climates. This ergonomic design ensures comfort and usability, reducing user fatigue during extended periods of operation. The rubberized clutch cover and handle reduce vibration, allowing for smoother handling and less strain on the operator.

In addition, the chainsaws are designed with a lightweight body, which enhances maneuverability. The magnesium and composite materials used in construction contribute to the overall durability without adding excessive weight. This combination makes it easy for users to handle the saw for both horizontal and vertical cuts.

The 357XP/XPG and 359G E-tech series include advanced bar and chain systems, providing superior cutting performance. The chains are designed for fast and efficient cutting, enabling users to tackle tough wood with minimal effort. The automatic oiler ensures that the bar and chain receive adequate lubrication, reducing wear and enhancing longevity.

For ease of use, the chainsaws are equipped with a tool-less chain tensioning system, allowing users to make quick adjustments without the need for additional tools. This feature highlights the user-friendly design that Husqvarna emphasizes in its products.

In summary, the Husqvarna 357XPG E-tech, 357XP, and 359G models stand out due to their advanced engine technologies, ergonomic features, lightweight construction, and practical design elements. These chainsaws offer a blend of performance, ease of use, and environmental responsibility, making them ideal tools for both professional lumberjacks and homeowners looking to accomplish tough cutting tasks efficiently.