Husqvarna 1153179-95, 359G E-tech, 357XP/XPG, 359/G manual Air filter, Spark plug, Fitting the starter

Page 35

MAINTENANCE

•Lubricate the recoil spring with light oil. Fit the cassette with recoil spring in the starter. Fit the starter pulley and tension the recoil spring.

Fitting the starter

•To fit the starter, first pull out the starter cord and place the starter in position against the crankcase. Then slowly release the starter cord so that the pulley engages with the pawls.

•Fit and tighten the screws that hold the starter.

Air filter

The air filter must be regularly cleaned to remove dust and dirt in order to avoid:

•Carburettor malfunctions

•Starting problems

•Loss of engine power

•Unnecessary wear to engine parts

•Excessive fuel consumption.

•Remove the air filter after taking off the air filter cover. When refitting make sure that the air filter seals tightly

against the filter holder. Clean the filter by brushing or shaking it.

The filter can be cleaned more thoroughly by washing it in water and detergent.

An air filter that has been in use for a long time cannot be cleaned completely. The filter must therefore be replaced with a new one at regular intervals. A damaged air filter must always be replaced.

A HUSQVARNA chain saw can be equipped with different types of air filters according to working conditions, weather, season, etc. Contact your dealer for advice.

Spark plug

The spark plug condition is influenced by:

•Incorrect carburetor adjustment.

•An incorrect fuel mixture (too much or incorrect type of oil).

•A dirty air filter.

These factors cause deposits on the spark plug electrodes, which may result in operating problems and starting difficulties.

If the machine is low on power, difficult to start or runs poorly at idle speed: always check the spark plug first before taking any further action. If the spark plug is dirty, clean it and check that the electrode gap is 0.020 inch (0.5 mm). The spark plug should be replaced after about a month in operation or earlier if necessary.

Note! Always use the recommended spark plug type! Use of the wrong spark plug can damage the piston/cylinder. Check that the spark plug is fitted with a suppressor.

English – 35

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Operator’s manual Symbols in the operator’s manual KEY to SymbolsSymbols on the machine EPA Contents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?Before using a new chain saw General Safety PrecautionsChain brake and front hand guard Machine′s safety equipmentAlways use common sense Personal protective equipmentGeneral Safety Precautions Right hand guard Throttle lockoutChain catcher Muffler Stop switchCutting equipment Vibration damping systemChain Cutting equipment designed to reduce kickbackBar Sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingGeneral information on sharpening cutting teeth Increases the risk of kickbackTensioning the chain Lubricating cutting equipment Checking wear on cutting equipment Chain drive sprocketNeedle bearing lubrication Working with the chain AssemblyFitting the bar and chain Fuel Fuel HandlingLong-term storage Fuel safetyFueling Transport and storageWarm engine Starting and StoppingStarting and stopping Cold engineStopping General working instructions Basic safety rulesWorking Techniques Before useJam. Always stop the engine before Clutch cover causing the chain toCleaning Terms Basic cutting techniqueOr fatal injury LimbingLogs are lying together. Such Clearing the trunk and preparing your retreat Tree felling techniqueSafe distance Felling directionFelling cut Training we advise you not to fell treesYour saw Directional cutsCutting trees and branches that are in tension General adviceFreeing a tree that has fallen badly Freeing a trapped treeWhat is kickback? How to avoid kickbackGeneral MaintenanceCarburetor adjustment High speed jet H Correctly adjusted carburetorChecking the brake trigger Muffler Changing a broken recoil spring Wound up in the starter housing it isChanging a broken or worn starter cord Tensioning the recoil springFitting the starter Air filterSpark plug Needle bearing lubrication Adjustment of the oil pumpWhen making adjustments Lubricating the bar tip sprocketHeated handles Air Injection centrifugal cleaningTemperature 0C 32F or colder Winter useDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data 058 Bar and chain combinations050 Saw chain filing and file gauges Your Warranty Rights and Obligations Federal Emission Control Warranty StatementOther safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Kickback safety precautionsOriginal instructions 1153179-95

1153179-95, 359/G, 359G E-tech, 357XP E-tech, 357XP/XPG specifications

The Husqvarna 357XPG E-tech and its counterparts, the 357XP/XPG, 357XP E-tech, and 359G E-tech, are noteworthy chainsaws designed for both professionals and enthusiasts who demand reliability and performance. These models encompass advanced technologies that enhance their functionality, making them suitable for a variety of cutting tasks.

One of the standout features of the 357XPG and its siblings is the E-tech engine technology. This system is designed to provide high performance while minimizing environmental impact. The E-tech engines are known for delivering efficient fuel consumption and lower emissions, making them compliant with stringent regulations and eco-friendly.

The chainsaw is equipped with an air injection system that pre-cleans the intake air, reducing the amount of debris that enters the engine. This results in longer air filter life and reduces maintenance, allowing users to focus more on their cutting tasks rather than frequent cleanings.

The 357XPG model is also equipped with a heated handle, a valuable feature for those working in colder climates. This ergonomic design ensures comfort and usability, reducing user fatigue during extended periods of operation. The rubberized clutch cover and handle reduce vibration, allowing for smoother handling and less strain on the operator.

In addition, the chainsaws are designed with a lightweight body, which enhances maneuverability. The magnesium and composite materials used in construction contribute to the overall durability without adding excessive weight. This combination makes it easy for users to handle the saw for both horizontal and vertical cuts.

The 357XP/XPG and 359G E-tech series include advanced bar and chain systems, providing superior cutting performance. The chains are designed for fast and efficient cutting, enabling users to tackle tough wood with minimal effort. The automatic oiler ensures that the bar and chain receive adequate lubrication, reducing wear and enhancing longevity.

For ease of use, the chainsaws are equipped with a tool-less chain tensioning system, allowing users to make quick adjustments without the need for additional tools. This feature highlights the user-friendly design that Husqvarna emphasizes in its products.

In summary, the Husqvarna 357XPG E-tech, 357XP, and 359G models stand out due to their advanced engine technologies, ergonomic features, lightweight construction, and practical design elements. These chainsaws offer a blend of performance, ease of use, and environmental responsibility, making them ideal tools for both professional lumberjacks and homeowners looking to accomplish tough cutting tasks efficiently.
Top Page Image Contents