Husqvarna 357XPG E-tech Training we advise you not to fell trees, Your saw, Directional cuts

Page 27

WORKING TECHNIQUES

starts to fall. Your path of retreat should be roughly 135 degrees away from the intended felling direction.

The line where the two cuts meet is called the directional cut line. This line should be perfectly horizontal and at right angles (90°) to the chosen felling direction.

Danger

zone

 

 

direction

 

 

Felling

 

 

 

 

 

 

 

 

 

Retreat path

 

Danger

 

Danger

zone

path

zone

 

 

 

 

 

 

Retreat

 

 

 

 

 

 

 

Felling

 

!

WARNING! Unless you have special

training we advise you not to fell trees

 

with a diameter larger than the bar length

 

of your saw!

Felling is done using three cuts. First you make the directional cuts, which consist of the top cut and the bottom cut, then you finish with the felling cut. By placing these cuts correctly you can control the felling direction very accurately.

Directional cuts

To make the directional cut you begin with the top cut. Aim using to the saw’s felling direction mark (1) toward a goal further forward in the terrain, where you would like the tree to fall (2). Stand on the right-hand side of the tree, behind the saw, and cut with a pull stroke.

Next make the bottom cut so that it finishes exactly at the end of the top cut.

The directional cuts should run 1/4 of the diameter through the trunk and the angle between the top cut and bottom cut should be 45°.

Felling cut

The felling cut is made from the opposite side of the tree and it must be perfectly horizontal. Stand on the left side of the tree and cut on the pull stroke.

Make the felling cut about 1.5-2 inches (3-5 cm) above the bottom directional cut.

Finish the felling cut parallel with the directional cut line so that the distance between them is at least 1/10 of the trunk diameter. The uncut section of the trunk is called the felling hinge.

The felling hinge controls the direction that the tree falls in.

All control over the felling direction is lost if the felling hinge is too narrow or non-existent, or if the directional cuts and felling cut are badly placed.

English – 27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Operator’s manual KEY to Symbols Symbols on the machineSymbols in the operator’s manual EPA Contents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?Before using a new chain saw General Safety PrecautionsChain brake and front hand guard Machine′s safety equipmentAlways use common sense Personal protective equipmentGeneral Safety Precautions Throttle lockout Chain catcherRight hand guard Muffler Stop switchCutting equipment Vibration damping systemCutting equipment designed to reduce kickback BarChain Sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingGeneral information on sharpening cutting teeth Increases the risk of kickbackTensioning the chain Lubricating cutting equipment Chain drive sprocket Needle bearing lubricationChecking wear on cutting equipment Assembly Fitting the bar and chainWorking with the chain Fuel Fuel HandlingLong-term storage Fuel safetyFueling Transport and storageWarm engine Starting and StoppingStarting and stopping Cold engineStopping General working instructions Basic safety rulesWorking Techniques Before useClutch cover causing the chain to CleaningJam. Always stop the engine before Terms Basic cutting techniqueLimbing Logs are lying together. SuchOr fatal injury Clearing the trunk and preparing your retreat Tree felling techniqueSafe distance Felling directionFelling cut Training we advise you not to fell treesYour saw Directional cutsCutting trees and branches that are in tension General adviceFreeing a tree that has fallen badly Freeing a trapped treeWhat is kickback? How to avoid kickbackMaintenance Carburetor adjustmentGeneral High speed jet H Correctly adjusted carburetorChecking the brake trigger Muffler Changing a broken recoil spring Wound up in the starter housing it isChanging a broken or worn starter cord Tensioning the recoil springAir filter Spark plugFitting the starter Needle bearing lubrication Adjustment of the oil pumpWhen making adjustments Lubricating the bar tip sprocketHeated handles Air Injection centrifugal cleaningTemperature 0C 32F or colder Winter useDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Bar and chain combinations 050058 Saw chain filing and file gauges Your Warranty Rights and Obligations Federal Emission Control Warranty StatementOther safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Kickback safety precautionsOriginal instructions 1153179-95

1153179-95, 359/G, 359G E-tech, 357XP E-tech, 357XP/XPG specifications

The Husqvarna 357XPG E-tech and its counterparts, the 357XP/XPG, 357XP E-tech, and 359G E-tech, are noteworthy chainsaws designed for both professionals and enthusiasts who demand reliability and performance. These models encompass advanced technologies that enhance their functionality, making them suitable for a variety of cutting tasks.

One of the standout features of the 357XPG and its siblings is the E-tech engine technology. This system is designed to provide high performance while minimizing environmental impact. The E-tech engines are known for delivering efficient fuel consumption and lower emissions, making them compliant with stringent regulations and eco-friendly.

The chainsaw is equipped with an air injection system that pre-cleans the intake air, reducing the amount of debris that enters the engine. This results in longer air filter life and reduces maintenance, allowing users to focus more on their cutting tasks rather than frequent cleanings.

The 357XPG model is also equipped with a heated handle, a valuable feature for those working in colder climates. This ergonomic design ensures comfort and usability, reducing user fatigue during extended periods of operation. The rubberized clutch cover and handle reduce vibration, allowing for smoother handling and less strain on the operator.

In addition, the chainsaws are designed with a lightweight body, which enhances maneuverability. The magnesium and composite materials used in construction contribute to the overall durability without adding excessive weight. This combination makes it easy for users to handle the saw for both horizontal and vertical cuts.

The 357XP/XPG and 359G E-tech series include advanced bar and chain systems, providing superior cutting performance. The chains are designed for fast and efficient cutting, enabling users to tackle tough wood with minimal effort. The automatic oiler ensures that the bar and chain receive adequate lubrication, reducing wear and enhancing longevity.

For ease of use, the chainsaws are equipped with a tool-less chain tensioning system, allowing users to make quick adjustments without the need for additional tools. This feature highlights the user-friendly design that Husqvarna emphasizes in its products.

In summary, the Husqvarna 357XPG E-tech, 357XP, and 359G models stand out due to their advanced engine technologies, ergonomic features, lightweight construction, and practical design elements. These chainsaws offer a blend of performance, ease of use, and environmental responsibility, making them ideal tools for both professional lumberjacks and homeowners looking to accomplish tough cutting tasks efficiently.
Top Page Image Contents