Husqvarna RZ19 CE / 966658901 manual Battery, To clean battery and terminals

Page 35

MAINTENANCE

Battery

Your mower is equipped with a maintenance free battery that does not need servicing. However, periodic charging of the battery with an automotive type battery charger will extend its life.

Keep battery and terminals clean.

Keep battery bolts tight.

See the chart for charging times.

To clean battery and terminals

Corrosion and dirt on the battery and terminals can cause the battery to “leak” power.

1.Open the terminal access doors.

2.Remove the red terminal guard.

3.Disconnect BLACK battery cable first, then the RED battery cable and remove the battery from the machine.

4.Rinse the battery with plain water and dry.

5.Clean terminals and battery cable ends with wire brush until shiny.

6.Coat terminals with grease or petroleum jelly

7.Reinstall battery.

IMPORTANT INFORMATION

Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.

Always use two wrenches for the terminal screws.

Replacing battery

1.Lift seat and rotate forward.

2.Remove the terminal guard.

3.Using two ½" wrenches disconnect BLACK battery cable then RED battery cable.

4.Unscrew the knob and remove battery hold down.

5.Carefully remove the battery from the mower.

6.Install new battery with terminals in the same position as the old battery.

7.Reinstall battery hold down.

8.First connect RED battery cable to positive (+) battery terminal with hex bolt and hex nut.

9.Connect BLACK grounding cable to negative (-) battery terminal with remaining hex bolt and hex nut.

10.Fit the terminal guard.

11.Lower seat.

Always use protective glasses when handling the battery.

STANDARD

STATE

APPROXIMATE BATTERY CHARGING TIME*

 

 

TO FULL CHARGE AT 80OF / 27OC

BATTERY

OF

 

 

 

 

 

Maximum Rate at:

 

 

 

 

 

 

CHARGE

 

 

 

 

 

50 Amps

30 Amps

20 Amps

10 Amps

 

 

 

 

 

 

 

 

12.6V

100%

- FULL CHARGE -

 

 

 

 

 

 

12.4V

75%

20 min.

35 min.

48 min.

90 min.

 

 

 

 

 

 

12.2V

50%

45 min.

75 min.

95 min.

180 min.

 

 

 

 

 

 

12.0V

25%

65 min.

115 min.

145 min.

280 min.

 

 

 

 

 

 

11.8V

0%

85 min.

150 min.

195 min.

370 min.

 

 

 

 

 

 

*Charging time depends on battery capacity,

condition, age, temperature and efficiency of charger

WARNING!

Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparks from accidental grounding.

8050-109

Battery cleaning and installation

35

Image 35
Contents Operator Manual Husqvarna. All rights reserved Contents Page Introduction Manufacturing Number Good ServiceXxxx xxxxxx xxxxx xxxx Xxxxxx xxxxxxxxx. xx xxxxxxxx Symbols and decalsManual Safety Instructions SafetyNever take passengers Slope Operation Personal Safety EquipmentChildren Safe Handling of Gasoline General Maintenance Risk of sparking Spark Arrestor TransportControl Locations ControlsSteering Control Levers Throttle Control Ignition SwitchParking Brake Refueling Choke ControlAlways use the high position F to transport Fuel Shut Off ValveMower Deck Lifting Lever TrackingBypass Linkage Blade Control LeverSteering TrainingStarting the Engine Before StartingPlace controls in neutral position Open the fuel valve To remove cables, reverse order Jumper cablesRunning Operating on Hills Mowing Tips Stopping the Engine Manual Transport Maintenance Schedule MaintenanceBefore After Year Always use protective glasses when handling the battery BatteryTo clean battery and terminals Tire Pressures Safety SystemTo replace deck belt BeltsDeck Belt Cutting Blades EZT BeltLeveling Deck Adjusting the Mower DeckCaster Wheels CleaningRemoval and installation of caster wheel Use protective glasses when cleaning and washingGeneral LubricationSteering Control Shafts Front Wheel MountFront Wheel Bearings Engine LubricationProblem Cause TroubleshootingTroubleshooting Winter Storage ServiceWiring Diagram Standard Hardware Technical DataTorque Specifications Transmission RZ19 CE EngineVibration Equivalent Vibration DimensionsRZ19 CE Equipment ProductivityNotified Body EU Declaration of Conformity InformationOnly applicable to European versions Business Name and AddressAction Date, mtr reading, stamp, sign Service JournalDelivery Service After the First 10 Hours Hour ServiceService Journal At Least Once Each Year Page 115 383927R1 10/26/10