Husqvarna YTH1848XPT To Adjust Mower Cutting Height See Fig, To Adjust Gauge Wheels See Fig

Page 10
With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole. Tighten securely.
Repeat for all, installing gauge wheel in same adjust- ment hole.
FIG.9

OPERATION

SYSTEM CHARACTERISTICS

The cruise control should only be used while mowing or transporting on relatively smooth, straight surfaces. Other conditions such as trimming at slow speeds may cause the cruise control to disengage. Do not use the cruise control on slopes, rough terrian or while trimmimg or turning.

With forward drive pedal depressed to desired speed, pull cruise control lever (J) up and hold while lifting your foot off the pedal, then release the lever.

NOTE: Adjust gauge wheels with tractor on a flat level surface.

Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in this section of manual).

To disengage the cruise control, depress the brake pedal

or tap on forward drive pedal.

 

J

K

L

FIG. 7

TO ADJUST MOWER CUTTING HEIGHT (See Fig. 8)

The position of the attachment lift lever (A) determines the cutting height.

A

FIG. 8

Put attachment lift lever in desired cutting height slot.

The cutting height range is approximately 1" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

The average lawn should be cut to approximately 2-1/2 inches during the cool season and to over 3 inches during hot months. For healthier and better looking lawns, mow often and after moderate growth.

For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS (See Fig. 9)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

10

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.You must remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your equipment on rough, rolling terrain or hills.

Select desired height of cut with attachment lift lever.

Start mower blades by engaging attachment clutch control.

TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped,or the deflector shield (S) in place.

S

FIG. 10

REVERSE OPERATION SYSTEM (ROS)

Your tractor is equipped with a Reverse Operation System (ROS). Any attempt by the operator to travel in the reverse direction with the attachment clutch engaged will shut off the engine unless ignition key is placed in the ROS "ON" position.

Image 10
Contents YTH1848XPT General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceIV. Towing Table of Contents Unassembled Parts AssemblyTools Required for Assembly To Remove Tractor from CartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor Reverse Operation System ROS on PositionHOW to USE Your Tractor StoppingSystem Characteristics To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Operate MowerTo Operate on Hills Service REMINDER/HOUR MeterBefore Starting the Engine To Transport See FigsPurge Transmission ADD GasolineTo Start Engine See Fig Automatic Transmission Warm UPMowing Tips Maintenance Before Each USEBrake Operation BatteryTractor TiresEngine Muffler CleaningEngine OIL Filter Spark PlugsTractor See Fig Service and AdjustmentsTo Install Mower See Figs To Remove MowerFirst Install ANTI-SWAY BAR S To Level Mower To Replace Mower Blade Drive Belt See Fig Mower Drive Belt RemovalTo Replace Motion Drive Belt See Fig Mower Drive Belt InstallationBelt Installation To Check BrakeFront Wheel TOE-IN/CAMBER To Start Engine with a Weak Battery See FigReplacing Battery See Fig To Remove Wheel for Repairs See FigTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Engine dies when Service Notes Schematic Tractor Model NO. YTH1848XPT 96043000700, Product no 43Electrical KEY Part Description Chassis Tractor Model NO. YTH1848XPT 96043000700, Product no 43 Drive Tractor Model NO. YTH1848XPT 96043000700, Product no 43 Steering Assembly Spark Arrester KIT EngineSeat Assembly Decals Wheels and TiresMower Deck 22 532 17 44-93 Stripper Mower Lift Suggested Guide for Sighting Slopes for Safe Operation Warranty Statement

YTH1848XPT specifications

The Husqvarna YTH1848XPT is a powerful and versatile lawn tractor designed to meet the needs of homeowners with expansive lawns or those who demand more from their mowing equipment. This model combines innovative features, advanced technology, and user-friendly characteristics to provide an exceptional mowing experience.

One of the standout features of the YTH1848XPT is its robust 18.5 HP Briggs & Stratton engine. This powerful engine ensures reliable performance, enabling the mower to tackle various terrain types efficiently. The engine is paired with a smooth hydrostatic transmission, allowing for easy speed adjustments and seamless operation without the need for shifting gears. This can significantly reduce the effort required for mowing and increase overall productivity.

The cutting deck on the YTH1848XPT is 48 inches wide, allowing for a quicker mowing time over larger areas. It is built for durability and features an efficient design that provides a clean, even cut. The deck can easily be adjusted to multiple cutting heights, ranging from 1 to 4 inches, allowing users to customize their mowing height based on their lawn’s specific requirements.

Further adding to its functionality, the YTH1848XPT is equipped with a robust chassis that enhances stability and handling. Its tight turning radius makes maneuvering around obstacles like trees and flower beds hassle-free. Additionally, the ergonomically designed seat provides comfort during extended mowing sessions, reducing operator fatigue.

Technologically, the YTH1848XPT comes with several advanced features that improve the mowing experience. The intuitive dashboard provides essential information at a glance, including fuel level, engine temperature, and service reminders. The mower also features a user-friendly cutting deck washout port, making deck cleaning simple and helping to maintain optimal performance.

Overall, the Husqvarna YTH1848XPT stands out as an efficient and user-friendly lawn tractor, suitable for homeowners who want to maintain their lawns with precision and ease. Its combination of powerful performance, advanced features, and thoughtful design ensures that it remains a reliable choice for those looking to invest in quality lawn care equipment. Whether tackling a small yard or expansive property, the YTH1848XPT delivers results that meet high expectations.