Husqvarna YTH1848XPT owner manual Front Wheel TOE-IN/CAMBER, To Remove Wheel for Repairs See Fig

Page 23

SERVICE AND ADJUSTMENTS

FRONT WHEEL TOE-IN/CAMBER

Your new tractor front wheel toe-in and camber is set at the factory and is normal. The front wheel toe-in and camber are not adjustable. If damage has occurred to affect the factory set front wheel toe-in or camber, contact a qualified service center.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 31)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE COVER

SQUARE KEY (REAR

WHEEL ONLY)

FIG. 31

TO START ENGINE WITH A WEAK BATTERY (See Fig. 32)

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

WEAK OR DEAD

 

 

 

 

 

 

 

FULLY CHARGED

BATTERY

 

 

 

 

 

 

 

BATTERY

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FIG. 32

REPLACING BATTERY (See Fig. 33)

WARNING: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent spark- ing from accidental grounding.

•Lift hood to raised position.

•Disconnect BLACK battery cable (A) then RED battery cable and carefully remove battery from tractor.

•Install new battery with terminals in same position as old battery.

•First connect RED battery cable (B) to positive (+) battery terminal with hex bolt and keps nut as shown. Tighten securely. Slide terminal cover (C) over terminal.

•Connect BLACK grounding cable to negative (-) battery terminal with remaining hex bolt and keps nut. Tighten securely

•Close hood.

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the MAINTENANCE sec- tion of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START

C

Positive B (Red) Cable

ANegative (Black) Cable

OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

02954

FIG. 33

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents YTH1848XPT II. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIV. Towing ServiceIII. Children Table of Contents To Remove Tractor from Carton AssemblyTools Required for Assembly Unassembled PartsCheck Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Reverse Operation System ROS on Position Know Your TractorStopping HOW to USE Your TractorTo Operate Mower To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig System CharacteristicsTo Transport See Figs Service REMINDER/HOUR MeterBefore Starting the Engine To Operate on HillsAutomatic Transmission Warm UP ADD GasolineTo Start Engine See Fig Purge TransmissionMowing Tips Before Each USE MaintenanceTires BatteryTractor Brake OperationEngine Spark Plugs CleaningEngine OIL Filter MufflerTo Remove Mower Service and AdjustmentsTo Install Mower See Figs Tractor See FigFirst Install ANTI-SWAY BAR S To Level Mower Mower Drive Belt Removal To Replace Mower Blade Drive Belt See FigTo Check Brake Mower Drive Belt InstallationBelt Installation To Replace Motion Drive Belt See FigTo Remove Wheel for Repairs See Fig To Start Engine with a Weak Battery See FigReplacing Battery See Fig Front Wheel TOE-IN/CAMBERTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting Points Engine dies when Service Notes Tractor Model NO. YTH1848XPT 96043000700, Product no 43 SchematicElectrical KEY Part Description Chassis Tractor Model NO. YTH1848XPT 96043000700, Product no 43 Drive Tractor Model NO. YTH1848XPT 96043000700, Product no 43 Steering Assembly Engine Spark Arrester KITSeat Assembly Wheels and Tires DecalsMower Deck 22 532 17 44-93 Stripper Mower Lift Suggested Guide for Sighting Slopes for Safe Operation Warranty Statement

YTH1848XPT specifications

The Husqvarna YTH1848XPT is a powerful and versatile lawn tractor designed to meet the needs of homeowners with expansive lawns or those who demand more from their mowing equipment. This model combines innovative features, advanced technology, and user-friendly characteristics to provide an exceptional mowing experience.

One of the standout features of the YTH1848XPT is its robust 18.5 HP Briggs & Stratton engine. This powerful engine ensures reliable performance, enabling the mower to tackle various terrain types efficiently. The engine is paired with a smooth hydrostatic transmission, allowing for easy speed adjustments and seamless operation without the need for shifting gears. This can significantly reduce the effort required for mowing and increase overall productivity.

The cutting deck on the YTH1848XPT is 48 inches wide, allowing for a quicker mowing time over larger areas. It is built for durability and features an efficient design that provides a clean, even cut. The deck can easily be adjusted to multiple cutting heights, ranging from 1 to 4 inches, allowing users to customize their mowing height based on their lawn’s specific requirements.

Further adding to its functionality, the YTH1848XPT is equipped with a robust chassis that enhances stability and handling. Its tight turning radius makes maneuvering around obstacles like trees and flower beds hassle-free. Additionally, the ergonomically designed seat provides comfort during extended mowing sessions, reducing operator fatigue.

Technologically, the YTH1848XPT comes with several advanced features that improve the mowing experience. The intuitive dashboard provides essential information at a glance, including fuel level, engine temperature, and service reminders. The mower also features a user-friendly cutting deck washout port, making deck cleaning simple and helping to maintain optimal performance.

Overall, the Husqvarna YTH1848XPT stands out as an efficient and user-friendly lawn tractor, suitable for homeowners who want to maintain their lawns with precision and ease. Its combination of powerful performance, advanced features, and thoughtful design ensures that it remains a reliable choice for those looking to invest in quality lawn care equipment. Whether tackling a small yard or expansive property, the YTH1848XPT delivers results that meet high expectations.
Top Page Image Contents