Husqvarna YTH1848XPT To Replace Motion Drive Belt See Fig, To Check Brake, Belt Removal

Page 22

SERVICE AND ADJUSTMENTS

MOWER DRIVE BELT INSTALLATION

•Install belt around all mandrel pulleys (R) and around idler pulleys (S) as shown.

•Install belt onto electric clutch pulley (M).

IMPORTANT: Check belt for proper routing in all mower pulley grooves.

•Reassemble mandrel covers (Q). Securely tighten all screws.

•Engage belt tension rod (K) on locking bracket (L).

CAUTION: Belt tension rod is spring loaded. Have a tight grip on rod and engage slowly.

•Raise attachment lift lever to highest position.

 

P

Q

P

 

 

M

K

R

 

L

Q

 

R

 

 

S

 

R

FIG. 29

TO REPLACE MOTION DRIVE BELT (See Fig. 30)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

•Remove mower (See “TO REMOVE MOWER” in this section of manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

•Disconnect clutch wire harness (A).

•Remove anti-rotation link (B) on right side of tractor.

•Remove belt from stationary idler (C) and clutching idler (D).

•Remove belt from centerspan idler (E).

•Pull belt slack toward rear of tractor. Carefully remove belt upwards from transmission input pulley and over cooling fan blades (F).

•Remove belt downward from engine pulley and around electric clutch (G).

•Slide belt toward rear of tractor, off the steering plate

(H) and remove from tractor.

BELT INSTALLATION -

•Install new belt from tractor rear to front, over the steer- ing plate (H) and above clutch brake pedal shaft (J).

•Pull belt toward front of tractor and roll belt around electric clutch and onto engine pulley (G).

•Pull belt toward rear of tractor. Carefully work belt down around transmission cooling fan and onto the input pulley (F). Be sure belt is inside the belt keeper.

•Install belt on centerspan idler (E).

•Install belt through stationary idler (C) and clutching idler (D).

•Reinstall anti-rotation link (B) on right side of tractor. Tighten securely.

•Reconnect clutch harness (A).

•Make sure belt is in all pulley grooves and inside all belt guides and keepers.

•Install mower (See “TO INSTALL MOWER” in this sec- tion of manual).

G

H

B

A

C

J

D

E

F

02953 electric

FIG. 30

TO CHECK BRAKE

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced.

You may also check brake by:

•Park tractor on a level, dry concrete or paved surface, depress brake pedal all the way down and engage parking brake.

•Disengage transmission by placing freewheel control in “transmission disengaged” position. Pull freewheel control out and into the slot and release so it is held in the disengaged position.

The rear wheels must lock and skid when you try to manu- ally push the tractor forward. If the rear wheels rotate, then the brake needs to be serviced. Contact a qualified service center.

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents YTH1848XPT General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceIV. Towing Table of Contents Unassembled Parts AssemblyTools Required for Assembly To Remove Tractor from CartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor Reverse Operation System ROS on PositionHOW to USE Your Tractor StoppingSystem Characteristics To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Operate MowerTo Operate on Hills Service REMINDER/HOUR MeterBefore Starting the Engine To Transport See FigsPurge Transmission ADD GasolineTo Start Engine See Fig Automatic Transmission Warm UPMowing Tips Maintenance Before Each USEBrake Operation BatteryTractor TiresEngine Muffler CleaningEngine OIL Filter Spark PlugsTractor See Fig Service and AdjustmentsTo Install Mower See Figs To Remove MowerFirst Install ANTI-SWAY BAR S To Level Mower To Replace Mower Blade Drive Belt See Fig Mower Drive Belt RemovalTo Replace Motion Drive Belt See Fig Mower Drive Belt InstallationBelt Installation To Check BrakeFront Wheel TOE-IN/CAMBER To Start Engine with a Weak Battery See FigReplacing Battery See Fig To Remove Wheel for Repairs See FigTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Engine dies when Service Notes Schematic Tractor Model NO. YTH1848XPT 96043000700, Product no 43Electrical KEY Part Description Chassis Tractor Model NO. YTH1848XPT 96043000700, Product no 43 Drive Tractor Model NO. YTH1848XPT 96043000700, Product no 43 Steering Assembly Spark Arrester KIT EngineSeat Assembly Decals Wheels and TiresMower Deck 22 532 17 44-93 Stripper Mower Lift Suggested Guide for Sighting Slopes for Safe Operation Warranty Statement

YTH1848XPT specifications

The Husqvarna YTH1848XPT is a powerful and versatile lawn tractor designed to meet the needs of homeowners with expansive lawns or those who demand more from their mowing equipment. This model combines innovative features, advanced technology, and user-friendly characteristics to provide an exceptional mowing experience.

One of the standout features of the YTH1848XPT is its robust 18.5 HP Briggs & Stratton engine. This powerful engine ensures reliable performance, enabling the mower to tackle various terrain types efficiently. The engine is paired with a smooth hydrostatic transmission, allowing for easy speed adjustments and seamless operation without the need for shifting gears. This can significantly reduce the effort required for mowing and increase overall productivity.

The cutting deck on the YTH1848XPT is 48 inches wide, allowing for a quicker mowing time over larger areas. It is built for durability and features an efficient design that provides a clean, even cut. The deck can easily be adjusted to multiple cutting heights, ranging from 1 to 4 inches, allowing users to customize their mowing height based on their lawn’s specific requirements.

Further adding to its functionality, the YTH1848XPT is equipped with a robust chassis that enhances stability and handling. Its tight turning radius makes maneuvering around obstacles like trees and flower beds hassle-free. Additionally, the ergonomically designed seat provides comfort during extended mowing sessions, reducing operator fatigue.

Technologically, the YTH1848XPT comes with several advanced features that improve the mowing experience. The intuitive dashboard provides essential information at a glance, including fuel level, engine temperature, and service reminders. The mower also features a user-friendly cutting deck washout port, making deck cleaning simple and helping to maintain optimal performance.

Overall, the Husqvarna YTH1848XPT stands out as an efficient and user-friendly lawn tractor, suitable for homeowners who want to maintain their lawns with precision and ease. Its combination of powerful performance, advanced features, and thoughtful design ensures that it remains a reliable choice for those looking to invest in quality lawn care equipment. Whether tackling a small yard or expansive property, the YTH1848XPT delivers results that meet high expectations.
Top Page Image Contents