Husqvarna 335LX manual Cutting equipment, Locking screw, General rules

Page 12

GENERAL SAFETY PRECAUTIONS

should operate the socket spanner when loosening or tightening the nut.

The nylon lining inside the locking nut must not be so worn that you can turn it by hand. The lining should offer a resistance of at least 1.5 Nm. The nut should be replaced after it has been put on approx. 10 times.

Locking screw

The lock screw must be tightened securely for ball- bearing-mounted support cups.

Cutting equipment

This section describes how to choose and maintain your cutting equipment in order to:

•Reduce the risk of blade thrust.

•Obtain maximum cutting performance.

•Extend the life of cutting equipment.

IMPORTANT!

Only use cutting attachments with the guards we recommend! See the chapter on Technical data.

Refer to the instructions for the cutting attachment to check the correct way to load the cord and the correct cord diameter.

Keep the teeth of the blade correctly sharpened! Follow our recommendations. Also refer to the instructions on the blade packaging.

Maintain the correct blade setting! Follow our instructions and use the recommended file gauge.

WARNING! Always stop the engine

! before doing any work on the cutting attachment.This continues to rotate even after the throttle has been released. Ensure that the cutting attachment has stopped completely and disconnect the HT lead from the spark plug before you start to work on it.

WARNING! Using an incorrect cutting

! attachment or an incorrectly sharpened blade increases the risk of blade thrust.

Cutting equipment

Saw blades are intended for cutting fibrous types of wood.

Grass blades and grass cutters are intended for cutting coarse grass.

A trimmer head is intended for trimming grass.

General rules

Only use cutting attachments with the guards we recommend! See the chapter on Technical data.

Keep the teeth of the blade correctly sharpened! Follow our instructions and use the recommended file gauge. An incorrectly sharpened or damaged blade increases the risk of accidents.

12 – English

Page 11 Page 13
Image 12
Page 11 Page 13
Contents 343F 345FX 345FXT 343FR 343FRM 343R 345RX KEY to Symbols SymbolsOperator of the machine must Ensure, while working, that no Persons or animals come closer thanContents Introduction Dear customerWhat is WHAT? What is what on the clearing saw? 343R, 345RXWhat is what on the clearing saw? 343F, 345FX, 345FXT What is what on the clearing saw? 343FR, 343FRM General Safety Precautions Personal protective equipmentMachine′s safety equipment Throttle lockoutStop switch Cutting attachment guardVibration damping system Quick releaseMuffler Locking nutCutting equipment Locking screwCutting equipment General rulesSharpening grass cutters and grass blades Sharpening the saw bladeTrimmer head Assembly Assembling the handlebar and throttleTransport position, handlebar Assembling the cutting equipment Fitting the blade guard and saw blade 343F, 345FX, 345FXT343FR, 343FRM, 343R, 345RX Fitting the trimmer guard and trimmer head Trimmy SII Fitting other guards and cutting attachmentsAdjusting the harness and clearing saw Standard harnessTriobalance harness Correct balance Fuel safety Fuel HandlingFuel Fueling MixingStarting and Stopping Check before startingStarting and stopping Cold engineStarting StoppingHeated handles Basic safety rules Working TechniquesGeneral working instructions ABC of clearingControl the felling direction take advantage of the wind Forestry clearing using a saw blade Grass clearing using a grass blade Brush cutting with a saw bladeGrass trimming with a trimmer head TrimmingCutting SweepingMaintenance CarburetorFine adjustment of the idle speed T Low speed jet LHigh speed jet H Correctly adjusted carburetor MufflerCooling system Proceed as followsCleaning the air filter Air filterBevel gear Oiling the air filterTemperature 5C 41F or colder Drive shaftSpark plug Winter useMaintenance schedule Maintenance Daily Weekly MonthlyTechnical Data Technical data345FX 345FXT Engine 343FR, 343FRM Centre hole in blades/cutters, Ø 25,4 mm Technical Data Federal Emission Control Warranty Statement Your Warranty Rights and ObligationsMAINTENANCE, Replacement Repair of EMISSION-RELATED Parts Page Trimmy SII Page Auto T45, T45x Page Page Page Page 1151096-95
Top Page Image Contents