Husqvarna 335LX manual Low speed jet L, Fine adjustment of the idle speed T, High speed jet H

Page 31

MAINTENANCE

Low speed jet L

Try to find the highest idling speed, turning the low speed needle L clockwise respectively counter-clockwise. When the highest speed has been found, turn the low speed needle L 1/4 turn counter-clockwise.

CAUTION! If the cutting attachment rotates when the engine is idling the idle adjustment screw T should be turned anti-clockwise until the cutting attachment stops.

Fine adjustment of the idle speed T

Adjust the idle speed using the idle adjustment screw T, if it is necessary to readjust. First turn the idle adjustment screw T clockwise until the cutting attachment starts to rotate. Then turn the screw anticlockwise until the cutting attachment stops. The idle speed is correctly adjusted when the engine will run smoothly in every position. The idle speed should also be well below the speed at which the cutting attachment starts to rotate.

WARNING! If the idle speed cannot be

! adjusted so that the cutting attachment stops, contact your dealer/service workshop. Do not use the machine until it has been correctly adjusted or repaired.

High speed jet H

The high speed jet H affects the engine power, speed, temperature and fuel consumption. If the high speed jet H is set too lean (screwed in too far) the engine speed will be too high and cause engine damage. Do not let the engine run at full speed for more than 10 seconds.

Setting procedure without a load (Blade can be used)

The machine is equipped with speed control in the ignition system. It is extremely important to be aware of this when adjusting the carburettor.

343R, 345RX: Speed control at: 12500 rpm

343F, 343FR, 343FRM, 345FX, 345FXT: Speed control

at: 13500 rpm

When attempting to adjust the speed over that specified, the speed is not changed, but only causes the engine to receive too little fuel resulting in a large risk of engine failure.

Run the machine warm for approximately 5 minutes alternating between short intervals of full throttle and idling. When the carburettor is to be adjusted, apply full throttle and turn the H-needle anti-clockwise until the engine speed reaches 10,500-11,000 r/min (burbles) or until the cap reaches its stop position. Now turn the H- needle slowly clockwise until the engine reaches the speed when the speed control comes into force. In some cases, speed control can come into force at 200-300 revs below or above that specified. It is important that you do not continue to turn the H-needle clockwise when the engine speed has stabilised. Screw the H-needle (anti- clockwise) a few tenths of a turn instead.

H

Setting procedure with a load (Trimmer head should be used)

Ensure the length of the trimmer cord is correct, i.e. exactly reaches the knife on the trimmer guard. Use either 3 mm or 3.3 mm diameter trimmer cord.

Run the machine warm for about 5 minutes mostly at full throttle. When the carburettor is to be adjusted, apply full throttle and turn the H-needle anti-clockwise until the engine burbles or until the cap reaches its stop position. (If the engine runs smoothly when the cap is in its stop position no further adjustment is necessary!) Turn the H- needle slowly clockwise until the engine runs absolutely

English – 31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents 343F 345FX 345FXT 343FR 343FRM 343R 345RX Persons or animals come closer than KEY to SymbolsSymbols Operator of the machine must Ensure, while working, that noContents Dear customer IntroductionWhat is what on the clearing saw? 343R, 345RX What is WHAT?What is what on the clearing saw? 343F, 345FX, 345FXT What is what on the clearing saw? 343FR, 343FRM Personal protective equipment General Safety PrecautionsThrottle lockout Machine′s safety equipmentQuick release Stop switchCutting attachment guard Vibration damping systemLocking nut MufflerGeneral rules Cutting equipmentLocking screw Cutting equipmentSharpening the saw blade Sharpening grass cutters and grass bladesTrimmer head Assembling the handlebar and throttle AssemblyTransport position, handlebar Assembling the cutting equipment 343F, 345FX, 345FXT Fitting the blade guard and saw blade343FR, 343FRM, 343R, 345RX Fitting other guards and cutting attachments Fitting the trimmer guard and trimmer head Trimmy SIIStandard harness Adjusting the harness and clearing sawTriobalance harness Correct balance Fuel Handling Fuel safetyFuel Mixing FuelingCold engine Starting and StoppingCheck before starting Starting and stoppingStopping StartingHeated handles ABC of clearing Basic safety rulesWorking Techniques General working instructionsControl the felling direction take advantage of the wind Forestry clearing using a saw blade Trimming Grass clearing using a grass bladeBrush cutting with a saw blade Grass trimming with a trimmer headSweeping CuttingCarburetor MaintenanceLow speed jet L Fine adjustment of the idle speed THigh speed jet H Proceed as follows Correctly adjusted carburetorMuffler Cooling systemOiling the air filter Cleaning the air filterAir filter Bevel gearWinter use Temperature 5C 41F or colderDrive shaft Spark plugMaintenance Daily Weekly Monthly Maintenance scheduleTechnical data Technical Data345FX 345FXT Engine 343FR, 343FRM Centre hole in blades/cutters, Ø 25,4 mm Technical Data Your Warranty Rights and Obligations Federal Emission Control Warranty StatementMAINTENANCE, Replacement Repair of EMISSION-RELATED Parts Page Trimmy SII Page Auto T45, T45x Page Page Page Page 1151096-95
Top Page Image Contents