Husqvarna 335LX manual Assembling the cutting equipment

Page 16

ASSEMBLY

Assembling the cutting equipment

WARNING!

! When fitting the cutting attachment it is extremely important that the raised section on the drive disc/support flange engages correctly in the centre hole of the cutting attachment. If the cutting attachment is fitted incorrectly it can result in serious and/or fatal personal injury.

•Fit the drive disc (B) on the angle gear’s output shaft.

•Centre the metal cup (P) on the drive disc’s blade guide.

•Turn the output shaft until one of the holes in the drive disk aligns with the corresponding hole in the gear housing.

•Insert the locking pin (C) in the hole to lock the shaft.

•Position the blade (D) with the drive disk (B). Make sure that the blade is centered by fitting it to the guide on the drive disk.

•Fit the support flange (F) on the output shaft so that it rests against the blade.

WARNING! Never use a cutting

! attachment without an approved guard. See the chapter on Technical data. If an incorrect or faulty guard is fitted this can cause serious personal injury.

D

N

E

F

P

BA C

IMPORTANT! If a saw blade or grass blade are to be used the machine must be equipped with the correct handlebar, blade guard and harness.

Fitting the blade guard/ combination guard, grass blade and ball-bearing-mounted support cup

•Hang the trimmer guard/combination guard (A) on the two hooks on the plate holder (M). Bend the guard around the shaft and tighten it with the bolt (L) on the opposite side of the shaft. Use the locking pin (C). Place the locking pin in the groove on the screw head and tighten. See diagram.

L

M C

A

CAUTION! Always use the recommended guard for the cutting attachment you are using. See chapter on Technical data.

ML

•Screw the support cup (E) onto the output shaft threads (CAUTION! Left-hand thread). Tighten to a torque of 35-50 Nm (3.5-5.0 kpm). Use the socket spanner in the tool kit. Note that the locking pin (C) must remain inside the gear housing to lock the drive disk. Hold the shaft of the socket spanner as close to the blade guard/combination guard as possible.

WARNING! Tighten the lock screw (N) in

! the center hole of the support cup. Tighten to a torque of 35-50 Nm (3.5-5.0 kpm), CAUTION! Left-hand thread. If the lock screw is not fitted in the support cup, there is a risk that the support cup will come unscrewed. This means that the blade will also come loose, which could result in serious or fatal injury to the operator or others.

16 – English

Page 15 Page 17
Image 16
Page 15 Page 17
Contents 343F 345FX 345FXT 343FR 343FRM 343R 345RX KEY to Symbols SymbolsOperator of the machine must Ensure, while working, that no Persons or animals come closer thanContents Introduction Dear customerWhat is WHAT? What is what on the clearing saw? 343R, 345RXWhat is what on the clearing saw? 343F, 345FX, 345FXT What is what on the clearing saw? 343FR, 343FRM General Safety Precautions Personal protective equipmentMachine′s safety equipment Throttle lockoutStop switch Cutting attachment guardVibration damping system Quick releaseMuffler Locking nutCutting equipment Locking screwCutting equipment General rulesSharpening grass cutters and grass blades Sharpening the saw bladeTrimmer head Assembling the handlebar and throttle AssemblyTransport position, handlebar Assembling the cutting equipment 343F, 345FX, 345FXT Fitting the blade guard and saw blade343FR, 343FRM, 343R, 345RX Fitting the trimmer guard and trimmer head Trimmy SII Fitting other guards and cutting attachmentsStandard harness Adjusting the harness and clearing sawTriobalance harness Correct balance Fuel Handling Fuel safetyFuel Fueling MixingStarting and Stopping Check before startingStarting and stopping Cold engineStopping StartingHeated handles Basic safety rules Working TechniquesGeneral working instructions ABC of clearingControl the felling direction take advantage of the wind Forestry clearing using a saw blade Grass clearing using a grass blade Brush cutting with a saw bladeGrass trimming with a trimmer head TrimmingCutting SweepingMaintenance CarburetorLow speed jet L Fine adjustment of the idle speed THigh speed jet H Correctly adjusted carburetor MufflerCooling system Proceed as followsCleaning the air filter Air filterBevel gear Oiling the air filterTemperature 5C 41F or colder Drive shaftSpark plug Winter useMaintenance schedule Maintenance Daily Weekly MonthlyTechnical Data Technical data345FX 345FXT Engine 343FR, 343FRM Centre hole in blades/cutters, Ø 25,4 mm Technical Data Federal Emission Control Warranty Statement Your Warranty Rights and ObligationsMAINTENANCE, Replacement Repair of EMISSION-RELATED Parts Page Trimmy SII Page Auto T45, T45x Page Page Page Page 1151096-95
Top Page Image Contents