Husqvarna 335LX Starting and Stopping, Check before starting, Starting and stopping, Cold engine

Page 23

STARTING AND STOPPING

Check before starting

•Check the blade to ensure that no cracks have formed at the bottom of the teeth or by the centre hole. The most common reason why cracks are formed is that sharp corners have been formed at the bottom of the teeth while sharpening or that the blade has been used with dull teeth. Discard a blade if cracks are found.

•Check that the support flange is not cracked due to fatigue or due to being tightened too much. Discard the support flange if it is cracked.

•Ensure the locking nut has not lost its captive force. The nut lock should have a locking force of at least 1.5 Nm. The tightening torque of the locking nut should be 35-50 Nm.

•Check that the blade guard is not damaged or cracked. Replace the blade guard if it is exposed to impact or is cracked.

Check that the trimmer head and trimmer guard are not damaged or cracked. Replace the trimmer head or trimmer guard if they have been exposed to impact or are cracked.

•Never use the machine without a guard nor with a defective guard.

•All covers must be correctly fitted and undamaged before you start the machine.

Starting and stopping

WARNING! The complete clutch cover

!and shaft must be fitted before the machine is started, otherwise the clutch can come loose and cause personal injury.

Always move the machine away from the refuelling area before starting. Place the machine on a flat surface. Ensure the cutting attachment cannot come into contact with any object.

Make sure no unauthorised persons are in the working area, otherwise there is a risk of serious personal injury.The safety distance is 15 metres.

Cold engine

Ignition: Set the stop switch to the start position.

Choke: Set the choke control (A) in the choke position.

Primer bulb: Press the air purge diaphragm (B) repeatedly until fuel begins to fill the diaphragm. The diaphragm need not be completely filled.

Warm engine

Use the same starting procedure as for a cold engine but without setting the choke control in the choke position.

Start throttle: (343F, 345FX, 345FXT, 343FR, 343FRM, 343R, 345RX)

Set the throttle to the start position by moving the choke control to the choke position and then returning it to its original position.

Start throttle: (343FR, 343FRM, 343R, 345RX)

Set the throttle to the start position by first pressing the throttle lockout and the throttle trigger, then pressing the start throttle button (A). Then release the throttle lockout and the throttle trigger, followed by the start throttle button. The throttle function is now activated. To return the

English – 23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents 343F 345FX 345FXT 343FR 343FRM 343R 345RX Persons or animals come closer than KEY to SymbolsSymbols Operator of the machine must Ensure, while working, that noContents Dear customer IntroductionWhat is what on the clearing saw? 343R, 345RX What is WHAT?What is what on the clearing saw? 343F, 345FX, 345FXT What is what on the clearing saw? 343FR, 343FRM Personal protective equipment General Safety PrecautionsThrottle lockout Machine′s safety equipmentQuick release Stop switchCutting attachment guard Vibration damping systemLocking nut MufflerGeneral rules Cutting equipmentLocking screw Cutting equipmentSharpening the saw blade Sharpening grass cutters and grass bladesTrimmer head Transport position, handlebar AssemblyAssembling the handlebar and throttle Assembling the cutting equipment 343FR, 343FRM, 343R, 345RX Fitting the blade guard and saw blade343F, 345FX, 345FXT Fitting other guards and cutting attachments Fitting the trimmer guard and trimmer head Trimmy SIITriobalance harness Adjusting the harness and clearing sawStandard harness Correct balance Fuel Fuel safetyFuel Handling Mixing FuelingCold engine Starting and StoppingCheck before starting Starting and stoppingHeated handles StartingStopping ABC of clearing Basic safety rulesWorking Techniques General working instructionsControl the felling direction take advantage of the wind Forestry clearing using a saw blade Trimming Grass clearing using a grass bladeBrush cutting with a saw blade Grass trimming with a trimmer headSweeping CuttingCarburetor MaintenanceHigh speed jet H Fine adjustment of the idle speed TLow speed jet L Proceed as follows Correctly adjusted carburetorMuffler Cooling systemOiling the air filter Cleaning the air filterAir filter Bevel gearWinter use Temperature 5C 41F or colderDrive shaft Spark plugMaintenance Daily Weekly Monthly Maintenance scheduleTechnical data Technical Data345FX 345FXT Engine 343FR, 343FRM Centre hole in blades/cutters, Ø 25,4 mm Technical Data Your Warranty Rights and Obligations Federal Emission Control Warranty StatementMAINTENANCE, Replacement Repair of EMISSION-RELATED Parts Page Trimmy SII Page Auto T45, T45x Page Page Page Page 1151096-95
Top Page Image Contents