Husqvarna 51 manual Air filter, Muffler, Needle bearing maintenance, Spark plug

Page 31

MAINTENANCE

Air filter

The air filter must be regularly cleaned from dust and dirt in order to avoid:

Carburetor malfunctions

Starting problems

Engine power reduction

Unnecessary wear on

the engine parts

• Abnormal fuel consumption

Clean the air filter daily or more often if the air is exceptionally dusty in the working area.

Disassemble the air filter by removing the cylinder cover

and unscrew the filter. When reassembling, make sure that the filter is tight against the filter holder. Clean the filter by brushing or shaking it.

A more thorough cleaning of the filter is obtained by washing it in water and soap.

An air filter, which is used for some time, cannot be cleaned completely. Therefore it must

Muffler

The muffler is designed in order to reduce the noise level and to direct the exhaust gases away from the operator. The exhaust gases are hot and can contain sparks, which may cause fire if directed against dry and combustible material. Some mufflers are equipped with a special screen. If your saw has this type of muffler, you should clean the screen at least once a week. This is done with a wire brush.

CAUTION! The screen must be replaced, if damaged. The saw will be overheated, if the screen is clogged. This results in damage on the cylinder and the piston. Never use a saw with a clogged or defective muffler.

Needle bearing maintenance

be replaced by a new one, with regular intervals.

IMPORTANT! A damaged air filter must always be replaced.

Spark plug

The spark plug condition is influenced by:

An incorrect carburetor setting.

Wrong fuel mixture (too much oil in the gasoline).

A dirty air filter.

These factors cause deposits on the spark plug electrodes, which may result in malfunction and starting difficulties.

If the engine is low on

 

power, difficult to start or

0,5 mm

runs poorly at idling speed,

 

always check the spark plug

 

first. If the spark plug is dirty,

 

clean it and check the

 

electrode gap. Readjust if

 

necessary. The correct gap is

 

0,5 mm (0,020"). The spark

 

plug should be replaced after

 

about a month in operation or

 

earlier if the electrodes are

 

badly eroded.

 

IMPORTANT! Always use the recommended spark plug type. An incorrect spark plug can severely damage the piston/cylinder.

The clutch drum is equipped with one of the following chain sprockets:

Spur sprocket (A) (the chain sprocket is welded on the drum)

Rim sprocket (B) (exchangeable)

Both versions have built-in needle bearing at the drive shaft, whitch has to be greased regularly (once a week).

NOTE! Use only high quality bearing grease.

A

B

English – 31

Image 31
Contents 101 91 51/55Symbols KEY to SymbolsContents Chain SAW Safety Equipment Safety InstructionsPersonal Protective Equipment Chain brake and front hand guard Chain catcher Throttle lockRight hand guard Vibration damping system Stop switchMuffler Checking the brake trigger Checking brake band wearChecking the front hand guard Checking the inertia brake releaseThrottle lock 5 basic rules Cutting EquipmentSome terms that describe the bar and chain Cutting equipment designed to minimise kickbackBar Saw chainGeneral information on sharpening cutting teeth Sharpening your chain and adjusting raker clearanceSharpening cutting teeth Setting the raker clearance General advice on setting raker clearanceTensioning the chain Chain oil Lubricating cutting equipmentFilling with chain oil Lubricating the bar tip sprocket Checking chain lubricationLubricating the clutch drum bearing Checking wear on cutting equipmentWhat is kickback? HOW to Avoid KickbackDo not let go of the handles General rulesMin m General Safety Precautions10 ft General Working Instructions Basic safety rulesCutting Basic cutting techniqueGeneral TermsFelling direction Tree felling techniqueSafe distance LimbingFelling Clearing the trunk and preparing your retreatCutting trees and branches that are in tension Preparations Freeing a tree that has fallen badly = high accident riskCutting the trunk into logs Freeing a Trapped treeWhat is WHAT? Mounting guide bar and chain AssemblyFuelmix Fuel HandlingMin 3 m Fuelling10ft Cold engine Start and StopStart StopCarburetor MaintenanceTensioning the recoil spring Starter device assemblyStarter device Changing a broken or worn starter cordSpark plug Needle bearing maintenanceAir filter MufflerCooling system Centrifugal cleaning Air InjectionTemperature 0C or colder Temperature -5C or colderMonthly maintenance Weekly maintenance Daily maintenanceTechnical Data Your Warranty Rights Obligations Emission Control Warranty Statement2001W07

51 specifications

The Husqvarna 51 is a well-regarded chainsaw that has made its mark in the world of outdoor power equipment. Renowned for its balance of performance and usability, the Husqvarna 51 is often favored by both amateur woodcutters and professionals alike. This versatile chainsaw is designed for a range of tasks, from light-duty pruning to more demanding woodcutting jobs.

One of the standout features of the Husqvarna 51 is its powerful 2.3 horsepower engine. This robust engine allows the saw to tackle larger cuts with ease, making it a reliable tool for any woodcutting needs. Coupled with a lightweight design, the chainsaw ensures reduced fatigue during prolonged use, enhancing user comfort and efficiency.

The Husqvarna 51 utilizes a simple yet effective starting system known as the Smart Start technology. This feature minimizes resistance in the starter cord, allowing for easier and quicker engine starts. Consequently, even less experienced users can confidently get the saw up and running without unnecessary frustration.

Another important characteristic of this model is its air injection system. This technology works by using centrifugal force to remove larger debris from the air filter before it reaches the engine. As a result, the filter stays cleaner for longer, reducing the frequency of maintenance and ensuring optimal engine performance. This system significantly prolongs the life of the chainsaw while maintaining high power levels.

The Husqvarna 51 also features an adjustable oil pump that allows operators to control oil flow as needed. This ensures proper lubrication of the chain and bar, which is critical for maintaining performance and extending the lifespan of the cutting components. The saw’s chrome-plated cylinder further contributes to durability by providing an added layer of resistance against wear and tear.

Safety is a priority with the Husqvarna 51, which comes equipped with an inertia-activated chain brake. This feature automatically stops the chain in the event of kickback, providing additional peace of mind to the user. The front hand guard and ergonomic handle design also enhance user control, contributing to a safer and more comfortable cutting experience.

Overall, the Husqvarna 51 stands out as a reliable, sturdy, and user-friendly chainsaw. Its blend of power, technology, and safety features makes it an ideal choice for a variety of cutting tasks, making it popular among both casual users and seasoned professionals. Whether you are trimming branches or cutting firewood, this chainsaw offers the performance you need for effective woodcutting.