Husqvarna 51 manual Cooling system, Winter use, Centrifugal cleaning Air Injection

Page 32

MAINTENANCE

Cooling system

To obtain the lowest possible running temperature the saw is equipped with a cooling system.

Winter use

During winter time, powder snow and cold weather can cause running problems, such as:

•Too low engine temperature.

•Icing on the air filter and carburetor.

Therefore some special measures are required:

The cooling system consists of:

1.Air intake on the starter unit.

2.Air guide plate.

3.Fan blades on the flywheel.

4.Cooling fins on the cylinder.

5.Cylinder cowling (supplies cold air over the cylinder).

5

4

3

2

1

•Partly reduce the air inlet of the starter and by doing that increase the engine temperature.

•Preheat the intake air to the carburetor by removing the special plug between the cylinder and the carburetor space.

Temperature 0°C or colder:

Twist the cover flap so that preheated air from the cylinder can enter the carburetor chamber to prevent icing of the filter. Fit the rubber seal to the fuel pipe by the

Clean the cooling system with a brush once a week, more often in demanding conditions. A dirty or blocked cooling system results in the saw overheating which causes damage to piston and cylinder.

Centrifugal cleaning ”Air Injection”

Centrifugal cleaning means the following:

All air to the carburetor is carried through the starter. Dirt and dust is centrifuged away by the cooling fan.

IMPORTANT! In order to keep the function of the centrifugal cleaning, a continous maintenance and care must be made.

• Clean the air intake to the starter, the fan wings of the flywheel, the space around the flywheel, inlet pipe and carburetor space.

main air intake.

Temperature -5°C or colder:

If the saw is to be used in cold weather or powder snow conditions a special cover flap can be fitted to the right side of the cylinder. This restricts the flow of cold air and reduces the amount of snow that is sucked in.

NOTE! If the special winterising kit has been fitted or any measures have been taken to increase the temperature these changes must be reversed before the saw is used in normal temperature conditions. Otherwise there is a risk that the saw will overheat, resulting in severe damage to the engine.

IMPORTANT! Any maintenance other than that described in this manual must be carried out by your servicing dealer.

32 – English

Page 31 Page 33
Image 32
Page 31 Page 33
Contents 51/55 101 91KEY to Symbols SymbolsContents Personal Protective Equipment Safety InstructionsChain SAW Safety Equipment Chain brake and front hand guard Right hand guard Throttle lockChain catcher Muffler Stop switchVibration damping system Checking brake band wear Checking the front hand guardChecking the inertia brake release Checking the brake triggerThrottle lock Cutting Equipment 5 basic rulesCutting equipment designed to minimise kickback BarSaw chain Some terms that describe the bar and chainSharpening cutting teeth Sharpening your chain and adjusting raker clearanceGeneral information on sharpening cutting teeth Tensioning the chain General advice on setting raker clearanceSetting the raker clearance Filling with chain oil Lubricating cutting equipmentChain oil Checking chain lubrication Lubricating the clutch drum bearingChecking wear on cutting equipment Lubricating the bar tip sprocketHOW to Avoid Kickback What is kickback?General rules Do not let go of the handles10 ft General Safety PrecautionsMin m Basic safety rules General Working InstructionsBasic cutting technique GeneralTerms CuttingTree felling technique Safe distanceLimbing Felling directionClearing the trunk and preparing your retreat FellingFreeing a tree that has fallen badly = high accident risk Cutting the trunk into logsFreeing a Trapped tree Cutting trees and branches that are in tension PreparationsWhat is WHAT? Assembly Mounting guide bar and chainFuel Handling Fuelmix10ft FuellingMin 3 m Start and Stop StartStop Cold engineMaintenance CarburetorStarter device assembly Starter deviceChanging a broken or worn starter cord Tensioning the recoil springNeedle bearing maintenance Air filterMuffler Spark plugCentrifugal cleaning Air Injection Temperature 0C or colderTemperature -5C or colder Cooling systemWeekly maintenance Daily maintenance Monthly maintenanceTechnical Data Emission Control Warranty Statement Your Warranty Rights Obligations2001W07

51 specifications

The Husqvarna 51 is a well-regarded chainsaw that has made its mark in the world of outdoor power equipment. Renowned for its balance of performance and usability, the Husqvarna 51 is often favored by both amateur woodcutters and professionals alike. This versatile chainsaw is designed for a range of tasks, from light-duty pruning to more demanding woodcutting jobs.

One of the standout features of the Husqvarna 51 is its powerful 2.3 horsepower engine. This robust engine allows the saw to tackle larger cuts with ease, making it a reliable tool for any woodcutting needs. Coupled with a lightweight design, the chainsaw ensures reduced fatigue during prolonged use, enhancing user comfort and efficiency.

The Husqvarna 51 utilizes a simple yet effective starting system known as the Smart Start technology. This feature minimizes resistance in the starter cord, allowing for easier and quicker engine starts. Consequently, even less experienced users can confidently get the saw up and running without unnecessary frustration.

Another important characteristic of this model is its air injection system. This technology works by using centrifugal force to remove larger debris from the air filter before it reaches the engine. As a result, the filter stays cleaner for longer, reducing the frequency of maintenance and ensuring optimal engine performance. This system significantly prolongs the life of the chainsaw while maintaining high power levels.

The Husqvarna 51 also features an adjustable oil pump that allows operators to control oil flow as needed. This ensures proper lubrication of the chain and bar, which is critical for maintaining performance and extending the lifespan of the cutting components. The saw’s chrome-plated cylinder further contributes to durability by providing an added layer of resistance against wear and tear.

Safety is a priority with the Husqvarna 51, which comes equipped with an inertia-activated chain brake. This feature automatically stops the chain in the event of kickback, providing additional peace of mind to the user. The front hand guard and ergonomic handle design also enhance user control, contributing to a safer and more comfortable cutting experience.

Overall, the Husqvarna 51 stands out as a reliable, sturdy, and user-friendly chainsaw. Its blend of power, technology, and safety features makes it an ideal choice for a variety of cutting tasks, making it popular among both casual users and seasoned professionals. Whether you are trimming branches or cutting firewood, this chainsaw offers the performance you need for effective woodcutting.
Top Page Image Contents