Husqvarna LTH1842 manual Mowing Tips, Purge Transmission, Automatic Transmission Warm UP

Page 14

OPERATION

AUTOMATIC TRANSMISSION WARM UP

•Before driving the unit in cold weather, the transmission should be warmed up as follows:

•Be sure the tractor is on level ground.

•Release the parking brake and let the brake slowly return to operating position.

•Allow one minute for transmission to warm up. This can be done during the engine warm up period.

•The attachments can be used during the engine warm- up period after the transmission has been warmed up and may require the choke control be pulled out slightly.

NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32 F) the carburetor fuel mixture may need to be adjusted for best engine performance. See “TO ADJUST CARBURETOR” in the Service and Adjustments section of this manual.

PURGE TRANSMISSION

CAUTION: Never engage or disengage freewheel lever while the engine is

running.

To ensure proper operation and performance, it is recom- mended that the transmission be purged before operating tractor for the first time. This procedure will remove any trapped air inside the transmission which may have de- veloped during shipping of your tractor.

IMPORTANT: SHOULD YOUR TRANSMISSION REQUIRE REMOVAL FOR SERVICE OR REPLACEMENT, IT SHOULD BE PURGED AFTER REINSTALLATION BEFORE OPERATING THE TRACTOR.

•Place tractor safely on level surface with engine off and parking brake set.

•Disengage transmission by placing freewheel control in freewheeling position (See “TO TRANSPORT” in this section of manual).

•Sitting in the tractor seat, start engine. After the en- gine is running, move throttle control to slow position. Disengage parking brake

•Depress forward drive pedal to full forward position, hold for five (5) seconds and release pedal. Depress reverse drive pedal to full reverse position, hold for five

(5) seconds and release pedal. Repeat this procedure three (3) times.

NOTE: During this procedure there will be no movement of drive wheels. The air is being removed from hydraulic drive system.

•Shut- off engine and set parking brake.

•Engage transmission by placing freewheel control in engaged position (See “TO TRANSPORT” in this sec- tion of manual).

•Sitting in the tractor seat, start engine. After the engine is running, move throttle control to half (1/2) speed. Disengage parking brake.

•Drive tractor forward for approximately five feet then backwards for five feet. Repeat this driving procedure three times.

Your transmission is now purged and now ready for normal operation.

MOWING TIPS

•Mower should be properly leveled for best mowing per- formance. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual.

•The left hand side of mower should be used for trim- ming.

•Drive so that clippings are discharged onto the area that has been cut. Have the cut area to the right of the machine. This will result in a more even distribution of clippings and more uniform cutting.

00272

FIG. 10

•When mowing large areas, start by turning to the right so that clippings will discharge away from shrubs, fences, driveways, etc. After one or two rounds, mow in the opposite direction making left hand turns until finished (See Fig. 10).

•If grass is extremely tall, it should be mowed twice to reduce load and possible fire hazard from dried clip- pings. Make first cut relatively high; the second to the desired height.

•Do not mow grass when it is wet. Wet grass will plug mower and leave undesirable clumps. Allow grass to dry before mowing.

•Alwaysoperateengineatfullthrottlewhenmowingto assurebettermowingperformanceandproperdischarge of material. Regulate ground speed by selecting a low enough gear to give the mower cutting performance as well as the quality of cut desired.

•When operating attachments, select a ground speed that will suit the terrain and give best performance of the attachment being used.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents LTH1842TWIN General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIV. Towing ServiceIII. Children Table of Contents Unassembled Parts Steering WheelTo Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidAttach Hood Scoop See b Install Seat See Figs a and 2bCheck Battery See a Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Move Forward and BackwardTo Operate Mower See Fig To Adjust Mower Cutting Height See FigUsing the Reverse Operation System Reverse Operation System ROSSee FigCheck Engine OIL Level Before Starting the EngineTo Transport See Figs ADD GasolineAutomatic Transmission Warm UP Mowing TipsPurge Transmission Service Dates MaintenanceLubrication Chart General RecommendationsTo Sharpen Blade See B TractorBlade Removal See a Check Operator Presence SystemEngine Cleaning To Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig Service and Adjustments To Replace Motion Drive BELTSee FIG Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Check BrakeTo Start Engine with a Weak Battery See Fig Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel Alignment Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points With attachment clutch Suggested Guide for Sighting Slopes for Safe Operation 532 41 22-42 01.19.07 AP

LTH1842 specifications

The Husqvarna LTH1842 is a reliable and efficient riding mower designed for homeowners who need a robust lawn care solution. Engineered with a focus on performance and user comfort, this model is an excellent choice for those maintaining medium to large-sized yards.

One of the standout features of the LTH1842 is its powerful 18.5 HP Briggs & Stratton engine. This engine provides ample power for a smooth cutting experience, ensuring that grass is cut evenly and effectively. Users will appreciate the automatic transmission, which allows for effortless speed adjustments and makes mowing a straightforward task, even on hilly terrain.

The cutting deck is another highlight of the Husqvarna LTH1842. With a width of 42 inches, it features a reinforced design that enhances durability. The cutting height can be adjusted to six different positions, ranging from 1 to 4 inches, giving users the flexibility to choose the perfect height for their lawn. Additionally, the fan-assisted bagger option helps collect grass clippings efficiently, promoting a cleaner mowing experience.

Ease of use is integrated throughout the design of the LTH1842. The ergonomic steering wheel and high-back seat are designed for comfort, especially during extended mowing sessions. The clear dashboard makes it simple for operators to monitor their speed and fuel levels without distraction.

Moreover, the Husqvarna LTH1842 incorporates advanced technology to enhance functionality. The ReadyStart system enables quick starts without the need for priming, ensuring that your mower is ready when you are. The mower is also compatible with a wide range of attachments, allowing it to perform additional tasks throughout different seasons, such as mulching and snow clearing.

Safety features, including an automatic shut-off mechanism when the operator leaves the seat, ensures that the user operates the machine securely. The LTH1842 also comes with a strong warranty, reflecting the manufacturer’s confidence in the machine's durability and performance.

In summary, the Husqvarna LTH1842 is a versatile riding mower that combines power, comfort, and innovative features. It is well-suited for homeowners looking for a reliable solution to maintain their lawns efficiently. With its robust engine, adjustable cutting deck, and user-friendly design, the LTH1842 delivers performance and convenience for a superior mowing experience.
Top Page Image Contents