Husqvarna LTH1538 owner manual Troubleshooting Points, Problem Cause Correction

Page 26

TROUBLESHOOTING POINTS

PROBLEM

CAUSE

CORRECTION

 

 

 

 

 

 

Will not start

1.

Out of fuel.

1.

Fill fuel tank.

 

2.

Engine not “CHOKED” properly.

2.

See “TO START ENGINE” in Operation section.

 

3.

Engine flooded.

3.

Wait several minutes before attempting to start.

 

4.

Bad spark plug.

4.

Replace spark plug.

 

5.

Dirty air filter.

5.

Clean/replace air filter.

 

6.

Dirty fuel filter.

6.

Replace fuel filter.

 

7.

Water in fuel.

7.

Empty fuel tank and carburetor, refill tank with fresh

 

 

 

 

gasoline and replace fuel filter.

 

8.

Loose or damaged wiring.

8.

Check all wiring.

 

9.

Carburetor out of adjustment.

9.

See “To Adjust Carburetor” in Service Adjustments

 

 

 

 

section.

 

10.

Engine valves out of adjustment.

10.

Contact an authorized service center/department.

 

 

 

 

 

 

Hard to start

1.

Dirty air filter.

1.

Clean/replace air filter.

 

2.

Bad spark plug.

2.

Replace spark plug.

 

3.

Weak or dead battery.

3.

Recharge or replace battery.

 

4.

Dirty fuel filter.

4.

Replace fuel filter.

 

5.

Stale or dirty fuel.

5.

Empty fuel tank and refill tank with fresh, clean gasoline.

 

6.

Loose or damaged wiring.

6.

Check all wiring.

 

7.

Carburetor out of adjustment.

7.

See “To Adjust Carburetor” in Service Adjustments

 

 

 

 

section.

 

8.

Engine valves out of adjustment.

8.

Contact an authorized service center/department.

 

 

 

 

 

 

Engine will not turn over

1.

Clutch/brake pedal not depressed.

1.

Depress clutch/brake pedal.

 

2.

Attachment clutch is engaged.

2.

Disengage attachment clutch.

 

3.

Weak or dead battery.

3.

Recharge or replace battery.

 

4.

Blown fuse.

4.

Replace fuse.

 

5.

Corroded battery terminals.

5.

Clean battery terminals.

 

6.

Loose or damaged wiring.

6.

Check all wiring.

 

7.

Faulty ignition switch.

7.

Check/replace ignition switch.

 

8.

Faulty solenoid or starter.

8.

Check/replace solenoid or starter.

 

9.

Faulty operator presence switch(es).

9.

Contact an authorized service center/department.

 

 

 

 

 

 

Engine clicks but will not

1.

Weak or dead battery.

1.

Recharge or replace battery.

start

2.

Corroded battery terminals.

2.

Clean battery terminals.

 

3.

Loose or damaged wiring.

3.

Check all wiring.

 

4.

Faulty solenoid or starter.

4.

Check/replace solenoid or starter.

 

 

 

 

 

 

Loss of power

1.

Cutting too much grass/too fast.

1.

Raise cutting height/reduce speed.

 

2.

Throttle in “CHOKE” position.

2.

Adjust throttle control.

 

3.

Build-up of grass, leaves and trash under mower.

3.

Clean underside of mower housing.

 

4.

Dirty air filter.

4.

Clean/replace air filter.

 

5.

Low oil level/dirty oil.

5.

Check oil level/change oil.

 

6.

Faulty spark plug.

6.

Clean and regap or change spark plug.

 

7.

Dirty fuel filter.

7.

Replace fuel filter.

 

8.

Stale or dirty fuel.

8.

Empty fuel tank and refill tank with fresh, clean gasoline.

 

9.

Water in fuel.

9.

Empty fuel tank and carburetor, refill tank with fresh

 

 

 

 

gasoline and replace fuel filter.

 

10.

Spark plug wire loose.

10.

Connect and tighten spark plug wire.

 

11.

Dirty engine air screen/fins.

11.

Clean engine air screen/fins.

 

12.

Dirty/clogged muffler.

12.

Clean/replace muffler.

 

13.

Loose or damaged wiring.

13.

Check all wiring.

 

14.

Carburetor out of adjustment.

14.

See “To Adjust Carburetor” in Service Adjustments

 

 

 

 

section.

 

15.

Engine valves out of adjustment.

15.

Contact an authorized service center/department.

 

 

 

 

 

 

Excessive vibration

1.

Worn, bent or loose blade.

1.

Replace blade. Tighten blade bolt.

 

2.

Bent blade mandrel.

2.

Replace blade mandrel.

 

3.

Loose/damaged part(s).

3.

Tighten loose part(s). Replace damaged parts.

 

 

 

 

 

 

26

Image 26
Contents LTH1538 General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Before Removing Tractor from Skid AssemblyTo Remove Tractor from Carton Unpack CartonAdjust Seat See Fig Install Seat See FigsCheck Battery See Fig Attach Hood Scoop See Fig Steps 1, 2Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor Stopping See Figs HOW to USE Your TractorTo SET Parking Brake See Fig To USE Throttle Control D See FigUsing the Reverse Operation System To Adjust Gauge Wheels See FigTo Adjust Mower Cutting Height See Fig To Move Forward and Backward See FigBefore Starting the Engine Automatic Transmission Warm UP Mowing TipsTo Start Engine Maintenance Lubrication ChartBlade Removal See Fig BatteryTractor Engine Cleaning To Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig Into the Cable Guide on Front Edge of Lower DashInstall belt on engine pulley M, in belt keepers G To Level Mower To Check Brake To Replace Mower Drive Belt See FigTo Replace Motion Drive Belt See Fig To Remove Wheel for Repairs See Fig To Start Engine with a Weak Battery See FigFront Wheel TOE-IN/CAMBER To Attach Jumper CablesTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Schematic Tractor - Model Number LTH1538 96043003800, Product no 43KEY Part Description DecalsWheels and Tires Electrical Socket Asm Bulb Twistlock Chassis 238 532 41 Trim 239 532 40 Clip Tinnerman Drive UNC 167 532 40 52-57 Latch Brake ParkingEngine Engine Power Rating Information Seat Assembly KEY PartSteering Assembly Mower Deck 532 40 30-12 Handle Clutch Cable Mower Lift Suggested Guide for Sighting Slopes for Safe Operation 532 41 07-13 REV1 12.07.06 TB