Husqvarna LT120 owner manual Tractor, Brake Operation, Tires, Blade Care, Battery

Page 15

CUSTOMER RESPONSIBILITIES

TRACTOR

Always observe safety rules when performing any mainte- nance.

BRAKE OPERATION

If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See “TO ADJUST BRAKE” in the Service and Adjust- ments section of this manual).

TIRES

Maintain proper air pressure in all tires (See “PROD- UCT SPECIFICATIONS” on page 3 of this manual).

Keep tires free of gasoline, oil, or insect control chemi- cals which can harm rubber.

Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

BLADE CARE

For best results mower blades must be kept sharp. Re- place bent or damaged blades.

BLADE REMOVAL (See Fig. 12)

Raise mower to highest position to allow access to blades.

Remove hex bolt, lock washer and flat washer securing blade.

Install new or resharpened blade with trailing edge up towards deck as shown.

Reassemble hex bolt, lock washer and flat washer in exact order as shown.

Tighten bolt securely (30-35 Ft. Lbs. torque).

IMPORTANT: BLADE BOLT IS GRADE 8 HEAT TREATED.

NOTE: We do not recommend sharpening blade - but if you do, be sure the blade is balanced.

BLADE

MANDREL

 

ASSEMBLY

TRAILING EDGE

FLAT WASHER

LOCK WASHER

HEX BOLT (GRADE 8)*

*A GRADE 8 HEAT TREATED BOLT CAN BE

IDENTIFIED BY SIX LINES ON THE BOLT HEAD.

FIG. 12

TO SHARPEN BLADE (See Fig. 13)

Care should be taken to keep the blade balanced. An unbalanced blade will cause excessive vibration and even- tual damage to mower and engine.

The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower.

To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with bal- ancer).

Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

CENTER HOLE

5/8" BOLT

BLADE

 

OR PIN

 

FIG. 13

BATTERY

Your tractor has a battery charging system which is suffi- cient for normal use. However, periodic charging of the battery with an automotive charger will extend its life.

Keep battery and terminals clean.

Keep battery bolts tight.

Keep small vent holes open.

Recharge at 6-10 amperes for 1 hour.

TO CLEAN BATTERY AND TERMINALS

Corrosion and dirt on the battery and terminals can cause the battery to “leak” power.

Open battery box door.

Disconnect BLACK battery cable first then RED bat- tery cable and remove battery from tractor.

Rinse the battery with plain water and dry.

Clean terminals and battery cable ends with wire brush until bright.

Coat terminals with grease or petroleum jelly.

Reinstall battery (See “CONNECT BATTERY” in the Assembly section of this manual).

15

Image 15
Contents LT 1 2 II. Slope Operation IV. ServiceSafe Operation Practices for Ride-On Mowers General OperationProduct Specifications Customer ResponsibilitiesModel Number LT120 Serial Table of Contents Contents of Hardware Pack To Remove Tractor from Carton AssemblyTools Required for Assembly HOW to SET UP Your TractorInstall Mulcher Plate See Figs Install Seat See FigCheck for Proper Position of ALL Belts To Convert to Bagging or DischargingCheck Tire Pressure Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor ADD Gasoline Before Starting the EngineTo Operate on Hills To TransportMulching Mowing Tips Mowing TipsBefore Each USE Lubrication ChartCustomer Responsibilities General RecommendationsTires BatteryTractor Brake OperationLubrication EngineBelts Transaxle CoolingCleaning MufflerSpark Plugs Service and Adjustments To Install Mower See FigTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Motion Drive Belt See Fig To Adjust Brake See FigBelt Installation To Replace Mower Blade Drive Belt See FigFront Wheel TOE-IN/CAMBER To Adjust Steering Wheel AlignmentTo Start Engine with a Weak Battery See Fig Transaxle Shifter Linkage and AD- Justment See FigsInterlocks and Relays To Remove Hood and Grill Assembly See FigTo Adjust Throttle Control Cable See Fig To Replace Headlight BulbAcceleration Test To Adjust Carburetor See FigPreliminary Setting Final SettingEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsOFF Slope CUT This OUT Dotted Is aLimited Warranty Warranty StatementSchematic Ignition SwitchWiring Insulated Clips Electrical KEY Part NO. NO. Description Chassis and Enclosures Repair Parts Drive KEY Part NO. no Description Steering Assembly KEY Part Description NO. no Seat Assembly Decals Wheels & TiresKEY Part Description Engine Repair Parts Mower Deck Repair Parts Mower Lift Repair Parts Peerless Transaxle Model Number 930-054A Part Description Rev 10.07.96 Kfsw

LT120 specifications

The Husqvarna LT120 represents a remarkable balance of performance, durability, and user-friendly design, making it an ideal choice for homeowners looking to maintain their lawns efficiently. This riding lawn mower is engineered with a focus on comfort and functionality, ensuring that each mowing session is as productive as possible.

One of the most notable features of the LT120 is its powerful 17.5 HP Briggs & Stratton engine. This reliable engine ensures that the mower can tackle various terrains effortlessly, offering consistent power and performance even in challenging conditions. The efficient engine design also translates into lower fuel consumption, making it a cost-effective solution for lawn maintenance.

The LT120 boasts a 42-inch cutting deck, which allows for considerable coverage in a single pass. The deck is constructed from stamped steel, ensuring durability and longevity while providing a clean, precise cut. Additionally, the cutting height can be easily adjusted to six different settings, ranging from one to four inches, giving users the flexibility to achieve their desired lawn height.

For user comfort, the LT120 features an ergonomic steering wheel and a comfortable, adjustable seat. These enhancements make it easier for users to navigate their lawns for extended periods without discomfort. The mower's compact design also contributes to its maneuverability, allowing it to reach tight spaces and corners that larger models might struggle with.

Another impressive aspect of the Husqvarna LT120 is its easy-to-use hydrostatic transmission. This technology allows for smooth and seamless speed adjustments without the need for manual gear shifting. Users can simply press the pedals to change speed and direction, making the mowing experience more intuitive and less physically demanding.

Safety is paramount in the design of the LT120. It is equipped with features such as an automatic blade engagement system, which ensures that the blades only engage when the operator is seated. Additionally, the machine includes a reverse operating system that allows users to mow in reverse safely.

Overall, the Husqvarna LT120 combines power, efficiency, and comfort, making it a superb choice for residential lawn care. With its quality construction and thoughtful design features, it provides an exceptional mowing experience, helping homeowners achieve a well-maintained lawn with ease. Whether tackling small or medium-sized lawns, the LT120 ensures that lawn care is a task that can be handled with confidence and satisfaction.