Husqvarna LT120 owner manual Tools Required for Assembly, To Remove Tractor from Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(2)

7/16" wrenches

Tire pressure gauge

(1)

1/2" wrench

Utility knife

(1)

9/16" wrench

 

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton (See page 5).

•Cut, from top to bottom, along lines on all four corners of carton, and lay panels flat.

•Check for any additional loose parts or cartons and remove.

BEFORE ROLLING TRACTOR OFF SKID

ATTACH STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

•Slide extension shaft onto lower steering shaft. Align mounting holes in extension and lower shafts and install 5/16 hex bolt and locknut. Tighten securely.

IMPORTANT: TIGHTEN BOLT AND NUT SECURELY TO 18-22 FT. LBS TORQUE.

•Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

•Position front wheels of the tractor so they are pointing straight forward.

•Slide steering wheel adapter onto steering shaft exten- sion.

•Position steering wheel and sleeve assembly so cross bars are horizontal (left to right) and slide onto adapter.

•Assemble large flat washer, 3/8 lock washer, 3/8 hex bolt and tighten securely.

•Snap steering wheel insert into center of steering wheel.

•Remove protective plastic from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

STEERING

WHEEL INSERT

3/8 HEX BOLT

3/8 LOCK WASHER

LARGE FLAT

WASHER

STEERING

WHEEL

STEERING BOOT

EXTENSION

SHAFT

ADAPTER

5/16 HEX BOLT

 

5/16 LOCKNUT

LOWER

STEERING

SHAFT

FIG. 1

•Place gearshift lever in neutral (N) position.

•Roll tractor backwards off skid.

•Remove banding holding discharge guard up against tractor.

HOW TO SET UP YOUR TRACTOR

CONNECT BATTERY (See Figs. 2 and 3)

CAUTION: Do not short battery termi- nals. Before connecting battery, re- move metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparking from acciden- tal grounding.

TO ROLL TRACTOR OFF SKID (See Opera- tion section for location and function of con- trols)

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Release parking brake by depressing clutch/brake pedal.

•Remove cardboard packing from seat pan and lift seat pan to raised position.

•Open battery box door.

•Remove terminal protective caps and discard.

•If this battery is put into service after month and year indicated on label (label located between terminals) charge battery for minimum of one hour at 6-10 amps.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents LT 1 2 General Operation IV. ServiceSafe Operation Practices for Ride-On Mowers II. Slope OperationProduct Specifications Customer ResponsibilitiesModel Number LT120 Serial Table of Contents Contents of Hardware Pack HOW to SET UP Your Tractor AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig Install Mulcher Plate See FigsCheck Deck Levelness To Convert to Bagging or DischargingCheck Tire Pressure Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Transport Before Starting the EngineTo Operate on Hills ADD GasolineMowing Tips Mulching Mowing TipsGeneral Recommendations Lubrication ChartCustomer Responsibilities Before Each USEBrake Operation BatteryTractor TiresTransaxle Cooling EngineBelts LubricationCleaning MufflerSpark Plugs Service and Adjustments To Install Mower See FigTo Remove Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Replace Mower Blade Drive Belt See Fig To Adjust Brake See FigBelt Installation To Replace Motion Drive Belt See FigTransaxle Shifter Linkage and AD- Justment See Figs To Adjust Steering Wheel AlignmentTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Replace Headlight Bulb To Remove Hood and Grill Assembly See FigTo Adjust Throttle Control Cable See Fig Interlocks and RelaysFinal Setting To Adjust Carburetor See FigPreliminary Setting Acceleration TestFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionOFF CUT This OUT Dotted Is a SlopeWarranty Statement Limited WarrantySchematic Ignition SwitchWiring Insulated Clips Electrical KEY Part NO. NO. Description Chassis and Enclosures Repair Parts Drive KEY Part NO. no Description Steering Assembly KEY Part Description NO. no Seat Assembly Decals Wheels & TiresKEY Part Description Engine Repair Parts Mower Deck Repair Parts Mower Lift Repair Parts Peerless Transaxle Model Number 930-054A Part Description Rev 10.07.96 Kfsw

LT120 specifications

The Husqvarna LT120 represents a remarkable balance of performance, durability, and user-friendly design, making it an ideal choice for homeowners looking to maintain their lawns efficiently. This riding lawn mower is engineered with a focus on comfort and functionality, ensuring that each mowing session is as productive as possible.

One of the most notable features of the LT120 is its powerful 17.5 HP Briggs & Stratton engine. This reliable engine ensures that the mower can tackle various terrains effortlessly, offering consistent power and performance even in challenging conditions. The efficient engine design also translates into lower fuel consumption, making it a cost-effective solution for lawn maintenance.

The LT120 boasts a 42-inch cutting deck, which allows for considerable coverage in a single pass. The deck is constructed from stamped steel, ensuring durability and longevity while providing a clean, precise cut. Additionally, the cutting height can be easily adjusted to six different settings, ranging from one to four inches, giving users the flexibility to achieve their desired lawn height.

For user comfort, the LT120 features an ergonomic steering wheel and a comfortable, adjustable seat. These enhancements make it easier for users to navigate their lawns for extended periods without discomfort. The mower's compact design also contributes to its maneuverability, allowing it to reach tight spaces and corners that larger models might struggle with.

Another impressive aspect of the Husqvarna LT120 is its easy-to-use hydrostatic transmission. This technology allows for smooth and seamless speed adjustments without the need for manual gear shifting. Users can simply press the pedals to change speed and direction, making the mowing experience more intuitive and less physically demanding.

Safety is paramount in the design of the LT120. It is equipped with features such as an automatic blade engagement system, which ensures that the blades only engage when the operator is seated. Additionally, the machine includes a reverse operating system that allows users to mow in reverse safely.

Overall, the Husqvarna LT120 combines power, efficiency, and comfort, making it a superb choice for residential lawn care. With its quality construction and thoughtful design features, it provides an exceptional mowing experience, helping homeowners achieve a well-maintained lawn with ease. Whether tackling small or medium-sized lawns, the LT120 ensures that lawn care is a task that can be handled with confidence and satisfaction.
Top Page Image Contents