Husqvarna LGT24K54 To Move Forward and Backward See Fig, To Adjust Mower Cutting Height See Fig

Page 13

OPERATION

TO MOVE FORWARD AND BACKWARD (See Fig. 20)

The direction and speed of movement is controlled by the motion control lever. (J)

J

Fig. 20

•Start tractor with motion control lever in neutral position.

•Release parking brake.

•Slowly move motion control lever to desired position.

TO ADJUST MOWER CUTTING HEIGHT (See Fig. 21)

The position of the attachment lift lever (A) determines the cutting height.

A

Fig. 21

•Put attachment lift lever in desired cutting height slot.

The cutting height range is approximately 1" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

•The average lawn should be cut to approximately 2-1/2" during the cool season and to over 3" during hot months. For healthier and better looking lawns, mow often and after moderate growth.

•For best cutting performance, grass over 6" in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS (See Fig. 22)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE: Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in this section of manual).

•With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole. Tighten securely.

•Repeat for all, installing gauge wheel in same adjust- ment hole.

Fig.22

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitat- ing or cutting off when operating your equipment on rough, rolling terrain or hills.

•Select desired height of cut with attachment lift lever.

•Start mower blades by engaging attachment clutch control.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents LGT24K54 Safe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationGeneral Service ServiceIII. Children IV. TowingTable of Contents Rear 3/16 Lift Link Shoulder Bolt 1/4 O.D Unassembled PartsOil Drain Tube 4 O.DTools Required for Assembly AssemblyBefore Removing Tractor from Skid Turn Steering Wheel Left and Position Mower See Fig Install ANTI-SWAY BAR S if Equipped SeeANTI-SWAY BAR S Attach Rear Lift Links C See Fig Attach Mower Side Suspension Arms a to Chassis See FigAttach Front Link E See Fig Check Tire Pressure Install Belt on Engine Clutch Pulley M SeeCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor To SET Parking Brake See Fig HOW to USE Your TractorStopping See Fig To USE Throttle Control D See FigTo Adjust Gauge Wheels See Fig To Adjust Mower Cutting Height See FigTo Move Forward and Backward See Fig To Operate MowerReverse Operation System ROS To Stop Mower BladesTo Operate on Hills To Transport See FigsBefore Starting the Engine Service REMINDER/HOUR MeterCheck Engine OIL Level ADD GasolinePurge Transmission Mowing TipsMaintenance MaintenanceGeneral Recommendations ScheduleTractor BatteryBlade Care Blade Removal See FigEngine IN-LINE Fuel Filter See Fig CleaningDeck Washout Port See Fig To Install Mower Service and AdjustmentsTo Remove Mower See Fig To Replace Mower Blade Drive Belt See FigPrecision SIDE-TO-SIDE Adjustment See Fig Visual SIDE-TO-SIDE Adjustment See FigTo Level Mower To Check Brake To Replace Motion Drive Belt See FigTo Remove Wheel for Repairs See Fig Front Wheel TOE-IN/CAMBERTo Start Engine with a Weak Battery See Fig Transaxle Motion Control Lever Neutral Adjustment See FigReplacing Battery See Fig To Attach Jumper CablesTransmission Fuel System OtherEngine OIL CylindersProblem Cause Correction TroubleshootingBattery will not To run when operFires when turn Engine continuesTractor Model NO. LGT24K54 96043012701, Product no 43 SchematicElectrical KEY Part Description Chassis Tractor Model NO. LGT24K54 96043012701, Product no 43 Drive Bolt Rdhd Sqnk 3/8-16 x 2-3/4 Gr 110 EngineKEY Part NO. NO. Description Steering Assembly Wheels and Tires DecalsSeat Assembly Mower Deck 532 44 15-47 Deck Weldment Mower Mower Lift Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationLimitations and Exclusions HOW to Obtain Service Consumer Wheeled Warranty Chart Qjlqh 7UDQVPLVVLRQ 02.22.11 CL
Related manuals
Manual 48 pages 13.97 Kb

LGT24K54 specifications

The Husqvarna LGT24K54 is a robust lawn tractor designed to meet the needs of homeowners who value both performance and comfort. It brings together cutting-edge technology and user-friendly features, making it a smart choice for maintaining lawns of various sizes.

One of the standout features of the LGT24K54 is its powerful 24 HP engine. The engine is a high-performance Kohler unit, providing ample power to tackle even the toughest grass and terrains. This ensures that users can complete their mowing tasks efficiently without worrying about whether their equipment can handle the job.

The tractor is equipped with a 54-inch cutting deck, which allows for a wide cutting path. This feature means mowing can be accomplished faster than with smaller decks, making it ideal for larger yards. The cutting height is adjustable, ranging from 1.5 inches to 4 inches, accommodating different grass types and personal preferences.

Husqvarna has introduced several technologies in the LGT24K54 to enhance the user experience. It features an ergonomic steering wheel and seat that provide comfort during extended use. In addition, the easy-to-use dashboard includes intuitive controls for engaging the cutting deck, adjusting speed, and more, ensuring that even novice users can operate the mower with ease.

Another impressive characteristic of the LGT24K54 is its hydrostatic transmission. This feature allows for seamless speed variations and provides a smooth driving experience without the need for manual gear shifting. It makes navigating around obstacles and tight corners much simpler.

The tractor also has a wide range of optional accessories, including baggers, mulch kits, and front attachments, making it a versatile machine throughout the year. Whether you need to collect grass clippings or tackle snow in winter, the LGT24K54 can adapt to your needs.

In terms of durability, the Jonsered LGT24K54 comes with a heavy-duty frame and steel cutting deck, ensuring long-lasting performance even in demanding conditions. The reinforced construction helps resist wear and tear, so users can depend on their equipment year after year.

In conclusion, the Husqvarna LGT24K54 is a powerful and versatile lawn tractor that combines robust engineering with user-friendly features. Ideal for homeowners looking for efficiency and comfort, it brings together advanced technologies and smart design to ensure a pleasant mowing experience and a pristine lawn.
Top Page Image Contents