Husqvarna GTH26K54 To Adjust Mower Cutting Height See Fig, To Adjust Gauge Wheels See Fig

Page 13

OPERATION

J

FIG. 17

•Start tractor with motion control lever in neutral (N) position.

•Release parking brake.

•Slowly move motion control lever to desired position.

TO ADJUST MOWER CUTTING HEIGHT (See Fig. 18)

The position of the attachment lift lever (A) determines the cutting height.

A

FIG. 18

•Put attachment lift lever in desired cutting height slot.

The cutting height range is approximately 1" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

•The average lawn should be cut to approximately 2-1/2 inches during the cool season and to over 3 inches during hot months. For healthier and better looking lawns, mow often and after moderate growth.

•For best cutting performance, grass over 6 inches in height should be mowed twice. Make the fi rst cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS (See Fig. 19)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE: Adjust gauge wheels with tractor on a fl at level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in this section of manual).

•With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole. Tighten securely.

•Repeat for all, installing gauge wheel in same adjust- ment hole.

FIG. 19

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.You must remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your equipment on rough, rolling terrain or hills.

1.Select desired height of cut with attachment lift lever.

2.Start mower blades by engaging attachment clutch control.

TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped,or the deflector shield (S) in place.

S

FIG. 20

REVERSE OPERATION SYSTEM (ROS)

Your tractor is equipped with a Reverse Operation System (ROS). Any attempt by the operator to travel in the reverse direction with the attachment clutch engaged will shut off the engine unless ignition key is placed in the ROS "ON" position.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents GTH26K54 Safe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationGeneral Service ServiceIII. Children IV. TowingTable of Contents Mower Mower Front Wheel Unassembled PartsSlope Sheet KeysTools Required for Assembly AssemblyTo Remove Tractor from Carton Unpack CartonFirst Install ANTI-SWAY BAR S Install Mower and Drive Belt7/16 Check Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor Stopping HOW to USE Your TractorTo Adjust Gauge Wheels See Fig To Adjust Mower Cutting Height See FigTo Operate Mower Reverse Operation System ROSBefore Starting the Engine Service REMINDER/HOUR MeterTo Operate on Hills To Transport See FigsTo Start Engine See Fig ADD GasolinePurge Transmission Automatic Transmission Warm UPMowing Tips Maintenance MaintenanceGeneral Recommendations ScheduleTractor BatteryBrake Operation TiresEngine Muffler CleaningSpark Plugs IN-LINE Fuel Filter See FigTo Install Mower Service and AdjustmentsTractor See Fig To Remove MowerTurn nut right Turn nut left To raise mower To Replace Motion Drive Belt See Fig To Replace Mower Blade Drive Belt See FigReplacing Battery See Fig To Start Engine with a Weak Battery See FigTo Check Brake Front Wheel TOE-IN/CAMBERTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbOther StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsEngine dies when Tractor Model NO. GTH26K54 96043003100, Product no 43 SchematicElectrical KEY Part NO. NO. Description Chassis KEY Part Description Drive Transaxle, Hydro Steering Assembly Spark Arrester KIT EngineSeat Assembly Wheels and Tires DecalsMower Deck Tractor Model NO. GTH26K54 96043003100, Product no 43 Mower Lift Suggested Guide for Sighting Slopes for Safe Operation Warranty Statement

GTH26K54 specifications

The Husqvarna GTH26K54 is a powerful lawn tractor designed for homeowners who seek efficiency and comfort in their lawn maintenance. With its sleek design and robust engineering, this model exemplifies Husqvarna's commitment to quality and innovation.

At the heart of the GTH26K54 is a reliable 26 horsepower Briggs & Stratton engine, offering ample power for tough mowing tasks and ensuring smooth operation across various terrains. The automatic hydrostatic transmission allows for seamless speed adjustments, enhancing maneuverability and providing a user-friendly experience. This feature is particularly beneficial when tackling larger yards or navigating intricate landscapes.

One of the standout characteristics of the GTH26K54 is its 54-inch cutting deck, which is designed to deliver a precise and even cut. The cutting height can be easily adjusted from the operator's seat, with a range of settings to accommodate different grass lengths and conditions. Additionally, the deck comes equipped with a reinforced design, providing durability and resilience against potential damage from obstacles encountered during mowing.

Ergonomics play a significant role in the GTH26K54’s design. The adjustable high-back seat ensures comfort for prolonged use, while the strategically placed controls allow for easy access without sacrificing safety or efficiency. The clear instrumentation panel provides essential information such as fuel levels and engine diagnostics, empowering users to monitor their tractor’s performance effectively.

The GTH26K54 also features advanced technologies, including a durable cast-iron front axle, which enhances stability on uneven terrain and extends the overall lifespan of the tractor. Furthermore, the integrated cutting system improves grass collection for a cleaner finish, while optional mulching kits allow for cleaner lawns and beneficial return of nutrients to the soil.

When it comes to maintenance, Husqvarna has streamlined the process with accessible components, making it easy for owners to perform regular checks and service tasks. The tractor's durable construction minimizes the need for frequent repairs, making it a smart investment for dedicated homeowners.

In summary, the Husqvarna GTH26K54 stands out in the lawn care market as a powerful, versatile, and user-friendly tractor. With its impressive features, advanced technologies, and commitment to comfort, it is an ideal choice for anyone looking to achieve a pristine lawn with minimal hassle.
Top Page Image Contents