Husqvarna GTH26K54 Tools Required for Assembly, To Remove Tractor from Carton, Unpack Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping pur- poses.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1)

3/4" wrench

(1) Utility knife

(1)

9/16" wrench

(1) Pliers

(1)

Tire Pressure Gauge

When right or left hand is mentioned in this manual, it means from your point of view, when you are in the operat- ing position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton .

•Cut along dashed lines on all four panels of carton. Remove end panels and lay side panels fl at.

•Remove mower and packing materials.

•Check for any additional loose parts or cartons and remove.

A

FIG. 2

NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate instruction below to remove the tractor from the skid.

WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other people and objects.

CHECK BATTERY (See Fig. 1)

•Lift hood to raised position.

NOTE: If this battery is put into service after month and year indicated on label (L) (label is located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in Maintenance section of this manual for charging instructions).

TO ROLL TRACTOR OFF SKID (See Op- eration section for location and function of controls)

•Raise attachment lift lever to its highest position.

•Release parking brake by depressing brake pedal.

•Place freewheel control in disengaged position to dis- engage transmission (See “TO TRANSPORT” in the Operation section of this manual).

•Roll tractor forward off skid.

L

02931

FIG. 1

ADJUST SEAT (See Fig. 2)

•Sit in seat.

•Lift up adjustment lever (A) and slide seat until a com- fortable position is reached which allows you to press clutch/brake pedal all the way down.

•Release lever to lock seat in position.

TO DRIVE TRACTOR OFF SKID (See Op- eration section for location and function of controls)

•Be sure all the above assembly steps have been com- pleted.

•Check engine oil level and fi ll fuel tank with gasoline.

•Place freewheel control in "transmission engaged" position (see "TO TRANSPORT" in Operation section of this manual).

•Sit on seat in operating position, depress clutch/brake pedal and set the parking brake.

•Place motion control lever in neutral (N) position.

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Remove key from bag and start the engine (see "TO START ENGINE" in the Operation section of this man- ual). After engine has started, move throttle control to idle (slow) position.

•Release parking brake.

•Slowly move the motion control lever forward and slowly drive tractor off skid.

•Apply brake to stop tractor, set parking brake and place motion control lever in neutral position.

•Turn ignition key to "STOP" position.

6Continue with the instructions that follow.

Page 5 Page 7
Image 6
Page 5 Page 7
Contents GTH26K54 General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Slope Sheet Unassembled PartsMower Mower Front Wheel KeysTo Remove Tractor from Carton AssemblyTools Required for Assembly Unpack CartonInstall Mower and Drive Belt First Install ANTI-SWAY BAR S7/16 Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor StoppingTo Operate Mower To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig Reverse Operation System ROSTo Operate on Hills Service REMINDER/HOUR MeterBefore Starting the Engine To Transport See FigsPurge Transmission ADD GasolineTo Start Engine See Fig Automatic Transmission Warm UPMowing Tips General Recommendations MaintenanceMaintenance ScheduleBrake Operation BatteryTractor TiresEngine Spark Plugs CleaningMuffler IN-LINE Fuel Filter See FigTractor See Fig Service and AdjustmentsTo Install Mower To Remove MowerTurn nut right Turn nut left To raise mower To Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigTo Check Brake To Start Engine with a Weak Battery See FigReplacing Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Schematic Tractor Model NO. GTH26K54 96043003100, Product no 43Electrical KEY Part NO. NO. Description Chassis KEY Part Description Drive Transaxle, Hydro Steering Assembly Engine Spark Arrester KITSeat Assembly Decals Wheels and TiresMower Deck Tractor Model NO. GTH26K54 96043003100, Product no 43 Mower Lift Suggested Guide for Sighting Slopes for Safe Operation Warranty Statement

GTH26K54 specifications

The Husqvarna GTH26K54 is a powerful lawn tractor designed for homeowners who seek efficiency and comfort in their lawn maintenance. With its sleek design and robust engineering, this model exemplifies Husqvarna's commitment to quality and innovation.

At the heart of the GTH26K54 is a reliable 26 horsepower Briggs & Stratton engine, offering ample power for tough mowing tasks and ensuring smooth operation across various terrains. The automatic hydrostatic transmission allows for seamless speed adjustments, enhancing maneuverability and providing a user-friendly experience. This feature is particularly beneficial when tackling larger yards or navigating intricate landscapes.

One of the standout characteristics of the GTH26K54 is its 54-inch cutting deck, which is designed to deliver a precise and even cut. The cutting height can be easily adjusted from the operator's seat, with a range of settings to accommodate different grass lengths and conditions. Additionally, the deck comes equipped with a reinforced design, providing durability and resilience against potential damage from obstacles encountered during mowing.

Ergonomics play a significant role in the GTH26K54’s design. The adjustable high-back seat ensures comfort for prolonged use, while the strategically placed controls allow for easy access without sacrificing safety or efficiency. The clear instrumentation panel provides essential information such as fuel levels and engine diagnostics, empowering users to monitor their tractor’s performance effectively.

The GTH26K54 also features advanced technologies, including a durable cast-iron front axle, which enhances stability on uneven terrain and extends the overall lifespan of the tractor. Furthermore, the integrated cutting system improves grass collection for a cleaner finish, while optional mulching kits allow for cleaner lawns and beneficial return of nutrients to the soil.

When it comes to maintenance, Husqvarna has streamlined the process with accessible components, making it easy for owners to perform regular checks and service tasks. The tractor's durable construction minimizes the need for frequent repairs, making it a smart investment for dedicated homeowners.

In summary, the Husqvarna GTH26K54 stands out in the lawn care market as a powerful, versatile, and user-friendly tractor. With its impressive features, advanced technologies, and commitment to comfort, it is an ideal choice for anyone looking to achieve a pristine lawn with minimal hassle.
Top Page Image Contents