Husqvarna GTH2350 To Replace Mower Drive Belt, To Replace Mower Blade Drive Belt See Fig

Page 21

SERVICE AND ADJUSTMENTS

NOTE: Each full turn of adjustment nut will change mower height about 3/16".

•Recheck measurements after adjusting.

FRONT-TO-BACK ADJUSTMENT (See Figs. 19 and 20)-

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO-SIDE.

To obtain the best cutting results, the mower housing should be adjusted so the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its highest position.

Check adjustment on right side of tractor. Measure distance “F” directly in front of and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjustments, check that both front links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower housing, loosen nut “G” on both front links an equal number of turns.

•When distance “F” is 1/8" to 1/2" lower at front than rear, tighten nut “H” against trunnion on both front links.

•To raise front of mower housing, loosen nut “H” from trunnion on both front links. Tighten nut “G” on both front links an equal number of turns.

•When distance “F” is 1/8" to 1/2" lower at front than rear, tighten nut “H” against trunnion on both front links.

NOTE: Each full turn of nut “G” will change dim. “F” by approximately 3/8".

•Recheck side-to-side adjustment.

“F” GROUND LINE “F”

FIG. 19

BOTH FRONT LINKS MUST BE EQUAL

 

IN LENGTH

NUT “H”

NUT “G”

 

TRUNNION

FRONT PLATE

 

ASSEMBLY

 

FIG. 20

TO REPLACE MOWER DRIVE BELT

MOWER DRIVE BELT REMOVAL (See Fig. 21) -

•Park tractor on a level surface. Engage parking brake.

•Remove screws from L.H. mandrel cover and remove cover.

•Roll belt over the top of L.H. mandrel pulley.

•Remove belt from electric clutch pulley.

•Remove belt from idler pulleys.

•Remove any dirt or grass clippings which may have accumulated around mandrels and entire upper deck surface.

•Check primary idler arm and two idlers to see that they rotate freely.

•Be sure spring is securely hooked to primary idler arm and bolt in mower housing.

MOWER DRIVE BELT INSTALLATION (See Fig. 21) -

•Install belt in both idlers. Make sure belt is in both belt keepers at the idlers as shown.

•Install new belt onto electric clutch pulley.

•Roll belt into upper groove of L.H. mandrel pulley.

•Carefully check belt routing making sure belt is in the grooves correctly and inside belt keepers.

•Reassemble L.H. mandrel cover.

L.H.

SCREWS

 

 

MANDREL

 

 

 

COVER

 

 

ELECTRIC

 

 

 

 

 

 

 

 

CLUTCH

 

 

IDLER

PRIMARY

PULLEY

 

 

IDLER ARM

 

 

 

PULLEYS

 

SPRING

 

 

 

 

 

 

 

 

BOLT IN

 

 

 

 

MOWER

 

 

 

 

HOUSING

L.H.

 

 

 

 

MANDREL

 

 

 

 

MOWER

 

 

 

DRIVE

 

 

 

 

BELT

BELT

 

 

 

 

KEEPERS

 

 

FIG. 21

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 22)

Park the tractor on level surface. Engage parking brake.

•Remove mower drive belt (See “TO REPLACE MOWER DRIVE BELT” in this section of this manual).

•Remove mower (See “TO REMOVE MOWER” in this section of this manual).

•Remove screws from R.H. mandrel cover and remove cover. Unhook spring from bolt on mower housing.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents GTH2350 IV. Service Safety RulesGeneral Operation II. Slope OperationSafe Operation Practices for Ride-On Mowers Safety RulesTable of Contents Unassembled Parts Tools Required for Assembly AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonTo Attach Nose Roller See Fig Install Seat See FigInstall Mower and Drive Belt See Figs Check Tire Pressure Check Mower LevelnessCheck for Proper Position of ALL Belts Operation Know Your Tractor HOW to USE Your Tractor To Operate on Hills To Adjust Gauge Wheels See FigTo Transport See Figs To Operate Mower See FigTowing Carts and Other Attachments Before Starting the EngineCheck Engine OIL Level ADD GasolinePurge Transmission Mowing TipsCustomer Responsibilities Lubrication ChartGeneral Recommendations Before Each USETractor Engine Engine OIL Filter CleaningMuffler Spark PlugsTo Level Mower Housing Service and AdjustmentsTo Install Mower To Remove Mower See FigTo Replace Mower Blade Drive Belt See Fig To Replace Mower Drive BeltBelt Installation To Adjust Attachment Clutch See FigTo Replace Motion Drive Belt See Fig Belt RemovalTo Adjust Steering Wheel Alignment Transmission REMOVAL/REPLACEMENTFront Wheel TOE-IN Adjustment Front Wheel CamberTo Replace Headlight Bulb To Start Engine with a Weak Battery See FigInterlocks and Relays To Replace FuseTo Adjust Throttle Control Cable See Fig To Adjust Choke Control See FigsTo Adjust Carburetor Other StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsTroubleshooting Points Tractor - Model NO. GTH2350 GTHK2350A, Product no 56 SchematicElectrical KEY Part Description 138 Chassis and EnclosuresRepair Parts Ground Drive Transaxle Hydro Gear Steering Assembly KEY Part NO. NO. Description Spark Arrester KIT EngineEngine Kohler Model No. CV675 Seat Assembly Wheels & Tires DecalLift Assembly KEY Part NO. NO. Description Mower Deck KEY Part Description Warranty Statement Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation532 18 06-66 Rev 07.18.02 RH

GTH2350 specifications

The Husqvarna GTH2350 is a robust and versatile garden tractor designed for homeowners seeking a reliable solution for lawn maintenance. This mower boasts an impressive combination of performance, comfort, and durability, making it a standout choice in its category.

Powered by a reliable Kohler engine, the GTH2350 delivers 23 horsepower, providing sufficient power to tackle a variety of terrains and mowing tasks. The engine's overhead valve design enhances fuel efficiency and reduces emissions, contributing positively to the environment while ensuring long-lasting performance.

One of the main features of the GTH2350 is its 50-inch cutting deck. This expansive deck allows for efficient mowing over large areas, reducing the time required to get the job done. The deck is made from durable materials, ensuring it can withstand the rigors of frequent use. Additionally, the cutting height can be easily adjusted to achieve the desired grass length, with multiple settings to accommodate different grass types and conditions.

The GTH2350 utilizes a hydrostatic transmission, which provides smooth and effortless operation. This technology allows the driver to move forward or backward without the need for changing gears, making mowing more intuitive and comfortable, especially when navigating tight spaces or uneven terrain.

For added comfort, the GTH2350 features an ergonomic seat with armrests, ensuring that operators can enjoy extended mowing sessions without discomfort. The conveniently placed controls allow for easy access and operation, enhancing the overall user experience.

Maneuverability is another strong point of the Husqvarna GTH2350. With its tight turning radius, users can easily navigate around trees, flower beds, and other obstacles, making it an ideal choice for intricately landscaped yards. Additionally, the tractor comes equipped with large, durable wheels that provide stability and traction, promoting safe operation on various surfaces.

In terms of attachment capabilities, the GTH2350 is designed to accommodate numerous accessories. Users can attach a bagger for efficient grass collection, a mulching kit for returning nutrients to the soil, or even snow removal equipment for winter use. This versatility allows for year-round usability, making it an excellent investment for homeowners.

In conclusion, the Husqvarna GTH2350 is a well-rounded garden tractor that offers powerful performance, comfort, and adaptability. Its reliable engine, hydrostatic transmission, and cutting versatility make it suitable for a wide range of mowing tasks, making it a dependable choice for any homeowner's lawn care needs.
Top Page Image Contents