Husqvarna GTH2350 Transmission REMOVAL/REPLACEMENT, To Adjust Steering Wheel Alignment

Page 23

SERVICE AND ADJUSTMENTS

TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT (See Fig. 25)

The motion control lever has been preset at the factory and adjustment should not be necessary.

•Park tractor on level surface. Stop tractor by turning ignition key to “OFF” position and engage parking brake.

•Loosen the adjustment bolt in front of the right rear wheel.

•Move motion control lever to the neutral position (N).

•Tighten the adjustment bolt.

ADJUSTMENT

BOLT

FIG. 25

TRANSMISSION REMOVAL/REPLACEMENT

Should your transmission require removal for service or replacement, it should be purged after reinstallation before operating the tractor. See “PURGE TRANSMISSION” in Operation section of this manual.

TO ADJUST STEERING WHEEL ALIGNMENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble with crossbars horizontal. Tighten securely.

FRONT WHEEL TOE-IN ADJUSTMENT

Front wheel toe-in is required for proper steering operation. Toe-in was set at the factory and adjustment should not be necessary. If parts in the front axle or steering mechanism have been replaced or damaged, check toe-in and adjust if necessary.

TO CHECK TOE-IN (See Fig. 26) -

•Position front wheels straight ahead.

•Measure distance between wheels at front and rear of tires (dimensions “A” and “B”).

•Front dimension “A” should be 1/8" to 1/4" less than rear dimension “B”.

TO ADJUST TOE-IN (See Figs. 26 and 27) -

•Loosen jam nuts at adjustment sleeves on tie rod.

•Adjust tie rod until dimension “A” is 1/8" to 1/4" less than dimension “B”.

•Tighten jam nuts securely.

FRONT WHEEL CAMBER

The front wheel camber is not adjustable on your tractor. If damage has occurred to affect the front wheel camber, contact your nearest authorized service center/department.

B

FRONT OF TRACTOR

A

FIG. 26

ADJUSTMENT SLEEVE

TIE ROD

JAM NUTS

ADJUSTMENT SLEEVE

FIG. 27

TO REMOVE WHEEL FOR REPAIRS

FRONT WHEEL (See Fig. 28)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal.

•Repair tire and reassemble.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

REAR WHEEL -

•Block rear axle securely.

•Remove five (5) hub bolts to allow wheel removal.

•Repair tire and reassemble. Replace and tighten hub bolts securely.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE COVER

FIG. 28

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents GTH2350 II. Slope Operation Safety RulesIV. Service General OperationSafe Operation Practices for Ride-On Mowers Safety RulesTable of Contents Unassembled Parts To Remove Tractor from Carton AssemblyTools Required for Assembly HOW to SET UP Your TractorTo Attach Nose Roller See Fig Install Seat See FigInstall Mower and Drive Belt See Figs Check for Proper Position of ALL Belts Check Tire PressureCheck Mower Levelness Operation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigTo Operate on Hills To Transport See FigsADD Gasoline Before Starting the EngineTowing Carts and Other Attachments Check Engine OIL LevelPurge Transmission Mowing TipsBefore Each USE Lubrication ChartCustomer Responsibilities General RecommendationsTractor Engine Spark Plugs CleaningEngine OIL Filter MufflerTo Remove Mower See Fig Service and AdjustmentsTo Level Mower Housing To Install MowerTo Replace Mower Blade Drive Belt See Fig To Replace Mower Drive BeltBelt Removal To Adjust Attachment Clutch See FigBelt Installation To Replace Motion Drive Belt See FigFront Wheel Camber Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel Alignment Front Wheel TOE-IN AdjustmentTo Replace Fuse To Start Engine with a Weak Battery See FigTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Carburetor To Adjust Throttle Control Cable See FigTo Adjust Choke Control See Figs Engine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsTroubleshooting Points Tractor - Model NO. GTH2350 GTHK2350A, Product no 56 SchematicElectrical KEY Part Description 138 Chassis and EnclosuresRepair Parts Ground Drive Transaxle Hydro Gear Steering Assembly KEY Part NO. NO. Description Spark Arrester KIT EngineEngine Kohler Model No. CV675 Seat Assembly Wheels & Tires DecalLift Assembly KEY Part NO. NO. Description Mower Deck KEY Part Description Warranty Statement Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation532 18 06-66 Rev 07.18.02 RH

GTH2350 specifications

The Husqvarna GTH2350 is a robust and versatile garden tractor designed for homeowners seeking a reliable solution for lawn maintenance. This mower boasts an impressive combination of performance, comfort, and durability, making it a standout choice in its category.

Powered by a reliable Kohler engine, the GTH2350 delivers 23 horsepower, providing sufficient power to tackle a variety of terrains and mowing tasks. The engine's overhead valve design enhances fuel efficiency and reduces emissions, contributing positively to the environment while ensuring long-lasting performance.

One of the main features of the GTH2350 is its 50-inch cutting deck. This expansive deck allows for efficient mowing over large areas, reducing the time required to get the job done. The deck is made from durable materials, ensuring it can withstand the rigors of frequent use. Additionally, the cutting height can be easily adjusted to achieve the desired grass length, with multiple settings to accommodate different grass types and conditions.

The GTH2350 utilizes a hydrostatic transmission, which provides smooth and effortless operation. This technology allows the driver to move forward or backward without the need for changing gears, making mowing more intuitive and comfortable, especially when navigating tight spaces or uneven terrain.

For added comfort, the GTH2350 features an ergonomic seat with armrests, ensuring that operators can enjoy extended mowing sessions without discomfort. The conveniently placed controls allow for easy access and operation, enhancing the overall user experience.

Maneuverability is another strong point of the Husqvarna GTH2350. With its tight turning radius, users can easily navigate around trees, flower beds, and other obstacles, making it an ideal choice for intricately landscaped yards. Additionally, the tractor comes equipped with large, durable wheels that provide stability and traction, promoting safe operation on various surfaces.

In terms of attachment capabilities, the GTH2350 is designed to accommodate numerous accessories. Users can attach a bagger for efficient grass collection, a mulching kit for returning nutrients to the soil, or even snow removal equipment for winter use. This versatility allows for year-round usability, making it an excellent investment for homeowners.

In conclusion, the Husqvarna GTH2350 is a well-rounded garden tractor that offers powerful performance, comfort, and adaptability. Its reliable engine, hydrostatic transmission, and cutting versatility make it suitable for a wide range of mowing tasks, making it a dependable choice for any homeowner's lawn care needs.
Top Page Image Contents