Husqvarna GTH2350 To Adjust Throttle Control Cable See Fig, To Adjust Choke Control See Figs

Page 25

SERVICE AND ADJUSTMENTS

ENGINE

TO ADJUST THROTTLE CONTROL CABLE (See Fig. 32)

The throttle control has been preset at the factory and adjustment should not be necessary. Check adjustment as described below before loosening cable. If adjustment is necessary, proceed as follows:

•With engine not running, move throttle control lever to fast position.

•Check that speed control lever is against stop screw. If it is not, loosen casing clamp screw and pull throttle cable until lever is against screw. Tighten clamp screw securely.

TO ADJUST CHOKE CONTROL (See Figs. 32 and 33)

The choke control has been preset at the factory and adjustment should not be necessary. check adjustment as described below before loosening cable. If adjustment is necessary, proceed as follows:

•With engine not running, move choke control (located on dash panel) to full choke position.

IDLE FUEL

 

ADJUSTING

IDLE SPEED

NEEDLE

ADJUSTING

 

SCREW

 

THROTTLE

 

CONTROL

 

CABLE

STOP

 

SCREW

CHOKE

CLAMP

CONTROL

SCREW

CABLE

 

FIG. 32

•Remove air cleaner cover, filter and cartridge plate to expose carburetor choke (See “AIR FILTER” in the Customer Responsibilities section of this manual).

•Choke should be closed. If it is not, loosen casing clamp screw and move choke cable until choke is completely closed. Tighten casing clamp screw securely.

•Reassemble air cleaner.

TO ADJUST CARBURETOR

The carburetor has been present at the factory and adjust- ment should not be necessary. However, minor adjustment may be required to compensate for differences in fuel, temperature, altitude or load. If the carburetor does need adjustment, see engine manual.

High speed stop is factory adjusted. Do not adjust-damage may result.

CLOSED FOR

FULL CHOKE

FIG. 33

IMPORTANT: NEVER TAMPER WITH THE ENGINE GOVERNOR, WHICH IS FACTORY SET FOR PROPER ENGINE SPEED. OVERSPEEDING THE ENGINE ABOVE THE FACTORY HIGH SPEED SETTING CAN BE DANGEROUS. IF YOU THINK THE ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING, CONTACT YOUR N E A R E S T A U T H O R I Z E D S E R V I C E C E N T E R / DEPARTMENT, WHICH HAS PROPER EQUIPMENT AND E X P E R I E N C E T O M A K E A N Y N E C E S S A R Y ADJUSTMENTS.

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents GTH2350 IV. Service Safety RulesGeneral Operation II. Slope OperationSafe Operation Practices for Ride-On Mowers Safety RulesTable of Contents Unassembled Parts Tools Required for Assembly AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonTo Attach Nose Roller See Fig Install Seat See FigInstall Mower and Drive Belt See Figs Check Mower Levelness Check Tire PressureCheck for Proper Position of ALL Belts Operation Know Your Tractor HOW to USE Your Tractor To Operate on Hills To Adjust Gauge Wheels See FigTo Transport See Figs To Operate Mower See FigTowing Carts and Other Attachments Before Starting the EngineCheck Engine OIL Level ADD GasolinePurge Transmission Mowing TipsCustomer Responsibilities Lubrication ChartGeneral Recommendations Before Each USETractor Engine Engine OIL Filter CleaningMuffler Spark PlugsTo Level Mower Housing Service and AdjustmentsTo Install Mower To Remove Mower See FigTo Replace Mower Blade Drive Belt See Fig To Replace Mower Drive BeltBelt Installation To Adjust Attachment Clutch See FigTo Replace Motion Drive Belt See Fig Belt RemovalTo Adjust Steering Wheel Alignment Transmission REMOVAL/REPLACEMENTFront Wheel TOE-IN Adjustment Front Wheel CamberTo Replace Headlight Bulb To Start Engine with a Weak Battery See FigInterlocks and Relays To Replace FuseTo Adjust Choke Control See Figs To Adjust Throttle Control Cable See FigTo Adjust Carburetor Other StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsTroubleshooting Points Tractor - Model NO. GTH2350 GTHK2350A, Product no 56 SchematicElectrical KEY Part Description 138 Chassis and EnclosuresRepair Parts Ground Drive Transaxle Hydro Gear Steering Assembly KEY Part NO. NO. Description Spark Arrester KIT EngineEngine Kohler Model No. CV675 Seat Assembly Wheels & Tires DecalLift Assembly KEY Part NO. NO. Description Mower Deck KEY Part Description Warranty Statement Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation532 18 06-66 Rev 07.18.02 RH

GTH2350 specifications

The Husqvarna GTH2350 is a robust and versatile garden tractor designed for homeowners seeking a reliable solution for lawn maintenance. This mower boasts an impressive combination of performance, comfort, and durability, making it a standout choice in its category.

Powered by a reliable Kohler engine, the GTH2350 delivers 23 horsepower, providing sufficient power to tackle a variety of terrains and mowing tasks. The engine's overhead valve design enhances fuel efficiency and reduces emissions, contributing positively to the environment while ensuring long-lasting performance.

One of the main features of the GTH2350 is its 50-inch cutting deck. This expansive deck allows for efficient mowing over large areas, reducing the time required to get the job done. The deck is made from durable materials, ensuring it can withstand the rigors of frequent use. Additionally, the cutting height can be easily adjusted to achieve the desired grass length, with multiple settings to accommodate different grass types and conditions.

The GTH2350 utilizes a hydrostatic transmission, which provides smooth and effortless operation. This technology allows the driver to move forward or backward without the need for changing gears, making mowing more intuitive and comfortable, especially when navigating tight spaces or uneven terrain.

For added comfort, the GTH2350 features an ergonomic seat with armrests, ensuring that operators can enjoy extended mowing sessions without discomfort. The conveniently placed controls allow for easy access and operation, enhancing the overall user experience.

Maneuverability is another strong point of the Husqvarna GTH2350. With its tight turning radius, users can easily navigate around trees, flower beds, and other obstacles, making it an ideal choice for intricately landscaped yards. Additionally, the tractor comes equipped with large, durable wheels that provide stability and traction, promoting safe operation on various surfaces.

In terms of attachment capabilities, the GTH2350 is designed to accommodate numerous accessories. Users can attach a bagger for efficient grass collection, a mulching kit for returning nutrients to the soil, or even snow removal equipment for winter use. This versatility allows for year-round usability, making it an excellent investment for homeowners.

In conclusion, the Husqvarna GTH2350 is a well-rounded garden tractor that offers powerful performance, comfort, and adaptability. Its reliable engine, hydrostatic transmission, and cutting versatility make it suitable for a wide range of mowing tasks, making it a dependable choice for any homeowner's lawn care needs.
Top Page Image Contents