Husqvarna GTH2350 owner manual Install Mower and Drive Belt See Figs

Page 8

ASSEMBLY

INSTALL MOWER AND DRIVE BELT (See Figs. 5 and 6)

Be sure tractor is on level surface and mower suspension arms are raised with attachment lift control. Engage parking brake.

•Cut and remove ties securing anti-sway bar and belts. Swing anti-sway bar to left side of mower deck.

•Slide mower under tractor with deflector shield to right side of tractor.

IMPORTANT: CHECK BELT FOR PROPER ROUTING IN ALL MOWER PULLEY GROOVES.

•If equipped, turn height adjustment knob counterclock- wise until it stops.

•Lower mower linkage with attachment lift control.

•Install belt into electric clutch pulley groove.

•Place the suspension arms on inward pointing deck pins. Retain with double loop retainer spring with loops down as shown.

•Install front plate assembly to tractor suspension brack- ets and retain with single loop retainer springs as shown.

retainer springs between the plate and mower brackets.

NOTE: To assist in locating hole in flanged pin, the hole in pin is inline with notch on head of pin. If necessary, move mower side-to-side to give space between plate and mower brackets.

IMPORTANT: CHECK BELT FOR PROPER ROUTING IN ALL MOWER PULLEY GROOVES.

•Connect anti-sway bar to chassis bracket under left footrest and retain with double loop retainer spring.

•If equipped, turn height adjustment knob clockwise to remove slack from mower suspension.

•Raise deck to highest position.

•Assemble gauge wheels as shown using long shoulder bolts, 3/8 washers, and 3/8-16 center locknuts. Tighten securely.

•Adjust gauge wheels before operating mower as shown in the Operation section of this manual.

•Position front plate assembly between front mower brackets. Raise deck and plate assembly to align holes and insert flanged pins. Secure pins with double loop

 

 

CHASSIS

 

DOUBLE LOOP

BRACKET

 

SUSPENSION

 

RETAINER

 

ARMS

 

SPRING

 

 

SHOULDER

 

IDLER

GAUGE

PULLEY

BOLT

 

WHEEL

 

 

 

FRONT SUSPENSION

BRACKETS

 

ELECTRIC CLUTCH

 

PULLEY

FRONT

 

MOWER

 

BRACKET

FRONT PLATE

 

ASSEMBLY

3/8

WASHER

3/8-16 DOUBLE

CENTER LOOP

LOCKNUT RETAINER SPRING

USE PLIERS FOR

RETAINER SPRINGS

SINGLE

LOOP RETAINER

SPRINGS

ANTI-SWAY

 

BAR

DEFLECTOR

 

SHIELD

DOUBLE LOOP RETAINER SPRING (INWARD POINTING DECK PINS)

LOOP

DOWN

FIG. 5

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents GTH2350 Safety Rules IV. ServiceGeneral Operation II. Slope OperationSafety Rules Safe Operation Practices for Ride-On MowersTable of Contents Unassembled Parts Assembly Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonInstall Seat See Fig To Attach Nose Roller See FigInstall Mower and Drive Belt See Figs Check for Proper Position of ALL Belts Check Tire PressureCheck Mower Levelness Operation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Operate on HillsTo Transport See Figs To Operate Mower See FigBefore Starting the Engine Towing Carts and Other AttachmentsCheck Engine OIL Level ADD GasolineMowing Tips Purge TransmissionLubrication Chart Customer ResponsibilitiesGeneral Recommendations Before Each USETractor Engine Cleaning Engine OIL FilterMuffler Spark PlugsService and Adjustments To Level Mower HousingTo Install Mower To Remove Mower See FigTo Replace Mower Drive Belt To Replace Mower Blade Drive Belt See FigTo Adjust Attachment Clutch See Fig Belt InstallationTo Replace Motion Drive Belt See Fig Belt RemovalTransmission REMOVAL/REPLACEMENT To Adjust Steering Wheel AlignmentFront Wheel TOE-IN Adjustment Front Wheel CamberTo Start Engine with a Weak Battery See Fig To Replace Headlight BulbInterlocks and Relays To Replace FuseTo Adjust Carburetor To Adjust Throttle Control Cable See FigTo Adjust Choke Control See Figs Storage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionTroubleshooting Points Schematic Tractor - Model NO. GTH2350 GTHK2350A, Product no 56Electrical KEY Part Description Chassis and Enclosures 138Repair Parts Ground Drive Transaxle Hydro Gear Steering Assembly KEY Part NO. NO. Description Engine Spark Arrester KITEngine Kohler Model No. CV675 Seat Assembly Decal Wheels & TiresLift Assembly KEY Part NO. NO. Description Mower Deck KEY Part Description Warranty Statement Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX532 18 06-66 Rev 07.18.02 RH

GTH2350 specifications

The Husqvarna GTH2350 is a robust and versatile garden tractor designed for homeowners seeking a reliable solution for lawn maintenance. This mower boasts an impressive combination of performance, comfort, and durability, making it a standout choice in its category.

Powered by a reliable Kohler engine, the GTH2350 delivers 23 horsepower, providing sufficient power to tackle a variety of terrains and mowing tasks. The engine's overhead valve design enhances fuel efficiency and reduces emissions, contributing positively to the environment while ensuring long-lasting performance.

One of the main features of the GTH2350 is its 50-inch cutting deck. This expansive deck allows for efficient mowing over large areas, reducing the time required to get the job done. The deck is made from durable materials, ensuring it can withstand the rigors of frequent use. Additionally, the cutting height can be easily adjusted to achieve the desired grass length, with multiple settings to accommodate different grass types and conditions.

The GTH2350 utilizes a hydrostatic transmission, which provides smooth and effortless operation. This technology allows the driver to move forward or backward without the need for changing gears, making mowing more intuitive and comfortable, especially when navigating tight spaces or uneven terrain.

For added comfort, the GTH2350 features an ergonomic seat with armrests, ensuring that operators can enjoy extended mowing sessions without discomfort. The conveniently placed controls allow for easy access and operation, enhancing the overall user experience.

Maneuverability is another strong point of the Husqvarna GTH2350. With its tight turning radius, users can easily navigate around trees, flower beds, and other obstacles, making it an ideal choice for intricately landscaped yards. Additionally, the tractor comes equipped with large, durable wheels that provide stability and traction, promoting safe operation on various surfaces.

In terms of attachment capabilities, the GTH2350 is designed to accommodate numerous accessories. Users can attach a bagger for efficient grass collection, a mulching kit for returning nutrients to the soil, or even snow removal equipment for winter use. This versatility allows for year-round usability, making it an excellent investment for homeowners.

In conclusion, the Husqvarna GTH2350 is a well-rounded garden tractor that offers powerful performance, comfort, and adaptability. Its reliable engine, hydrostatic transmission, and cutting versatility make it suitable for a wide range of mowing tasks, making it a dependable choice for any homeowner's lawn care needs.
Top Page Image Contents