Husqvarna GTH2250 owner manual Troubleshooting Points, Problem Cause Correction

Page 28

TROUBLESHOOTING POINTS

PROBLEM

CAUSE

 

CORRECTION

 

 

 

 

 

Will not start

1.

Out of fuel.

1.

Fill fuel tank.

 

2.

Engine not “CHOKED” properly.

2.

See “TO START ENGINE” in Operation section.

 

3.

Engine flooded.

3.

Wait several minutes before attempting to start.

 

4.

Bad spark plug.

4.

Replace spark plug.

 

5.

Dirty air filter.

5.

Clean/replace air filter.

 

6.

Dirty fuel filter.

6.

Replace fuel filter.

 

7.

Water in fuel.

7.

Drain fuel tank and carburetor, refill tank with fresh

 

 

 

 

gasoline and replace fuel filter.

 

8.

Loose or damaged wiring.

8.

Check all wiring.

 

9.

Carburetor out of adjustment.

9.

See “To Adjust Carburetor” in Service Adjustments

 

 

 

 

section.

 

10.

Engine valves out of adjustment.

10.

Contact an authorized service center/department.

 

 

 

 

 

Hard to start

1.

Dirty air filter.

1.

Clean/replace air filter.

 

2.

Bad spark plug.

2.

Replace spark plug.

 

3.

Weak or dead battery.

3.

Recharge or replace battery.

 

4.

Dirty fuel filter.

4.

Replace fuel filter.

 

5.

Stale or dirty fuel.

5.

Drain fuel tank and refill with fresh gasoline.

 

6.

Loose or damaged wiring.

6.

Check all wiring.

 

7.

Carburetor out of adjustment.

7.

See “To Adjust Carburetor” in Service Adjustments

 

 

 

 

section.

 

8.

Engine valves out of adjustment.

8.

Contact an authorized service center/department.

 

 

 

 

 

Engine will not turn over

1.

Clutch/brake pedal not depressed.

1.

Depress clutch/brake pedal.

 

2.

Attachment clutch is engaged.

2.

Disengage attachment clutch.

 

3.

Weak or dead battery.

3.

Recharge or replace battery.

 

4.

Blown fuse.

4.

Replace fuse.

 

5.

Corroded battery terminals.

5.

Clean battery terminals.

 

6.

Loose or damaged wiring.

6.

Check all wiring.

 

7.

Faulty ignition switch.

7.

Check/replace ignition switch.

 

8.

Faulty solenoid or starter.

8.

Check/replace solenoid or starter.

 

9.

Faulty operator presence switch(es).

9.

Contact an authorized service center/department.

 

 

 

 

 

Engine clicks but will not

1.

Weak or dead battery.

1.

Recharge or replace battery.

start

2.

Corroded battery terminals.

2.

Clean battery terminals.

 

3.

Loose or damaged wiring.

3.

Check all wiring.

 

4.

Faulty solenoid or starter.

4.

Check/replace solenoid or starter.

 

 

 

 

 

Loss of power

1.

Cutting too much grass/too fast.

1.

Set in “Higher Cut” position/reduce speed.

 

2.

Throttle in “CHOKE” position.

2.

Adjust throttle control.

 

3.

Build-up of grass, leaves and trash under mower.

3.

Clean underside of mower housing.

 

4.

Dirty air filter.

4.

Clean/replace air filter.

 

5.

Low oil level/dirty oil.

5.

Check oil level/change oil.

 

6.

Faulty spark plug.

6.

Clean and regap or change spark plug.

 

7.

Dirty fuel filter.

7.

Replace fuel filter.

 

8.

Stale or dirty fuel.

8.

Drain fuel tank and refill with fresh gasoline.

 

9.

Water in fuel.

9.

Drain fuel tank and carburetor, refill tank with fresh

 

 

 

 

gasoline and replace fuel filter.

 

10.

Spark plug wire loose.

10.

Connect and tighten spark plug wire.

 

11.

Dirty engine air screen/fins.

11.

Clean engine air screen/fins.

 

12.

Dirty/clogged muffler.

12.

Clean/replace muffler.

 

13.

Loose or damaged wiring.

13.

Check all wiring.

 

14.

Carburetor out of adjustment.

14.

See “To Adjust Carburetor” in Service Adjustments

 

 

 

 

section.

 

15.

Engine valves out of adjustment.

15.

Contact an authorized service center/department.

 

 

 

 

 

Excessive vibration

1.

Worn, bent or loose blade.

1.

Replace blade. Tighten blade bolt.

 

2.

Bent blade mandrel.

2.

Replace blade mandrel.

 

3.

Loose/damaged part(s).

3.

Tighten loose part(s). Replace damaged parts.

 

 

 

 

 

 

 

 

 

 

28

Image 28
Contents GTH2250 IV. Service General OperationII. Slope Operation III. ChildrenSafety Rules Safe Operation Practices for Ride-On MowersTable of Contents Unassembled Parts Assembly Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonInstall Seat See Fig To Attach Nose Roller See FigCheck Tire Pressure Check Mower LevelnessCheck for Proper Position of ALL Belts Check Brake SystemChecklist Operation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Operate on HillsTo Transport See Figs Towing Carts and Other ATTACH- MentsBefore Starting the Engine Check Engine OIL Level See FigADD Gasoline To Start Engine See FigMowing Tips Purge TransmissionLubrication Chart Customer ResponsibilitiesGeneral Recommendations Before Each USETractor Engine Cleaning Engine OIL FilterMuffler Spark PlugsService and Adjustments To Level Mower HousingTo Install Mower To Remove Mower See FigTo Replace Mower Drive Belt To Adjust Brake See Fig To Adjust Attachment Clutch See FigTo Replace Mower Blade Drive Belt See Fig To Adjust Motion Control Lever See Fig Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel Alignment Front Wheel TOE-IN AdjustmentFront Wheel Camber To Start Engine with a Weak Battery See FigTo Remove Wheel for Repairs Interlocks and Relays To Replace Headlight BulbTo Replace Fuse To Adjust Choke Control See Fig To Adjust Throttle Control Cable See FigTo Adjust Carburetor Storage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionOFF Service Notes Tractor - Model NO. GTH2250A Schematic Tractor - Model NO. GTH2250A ElectricalKEY Part Description Chassis and Enclosures 532177956 Ground Drive KEY Part NO. NO. Description Steering Assembly Adapter, Wheel Steering Engine Spark Arrester KITSeat Assembly Decals Wheels & TiresLift Assembly 532130171Mower Deck Wheel, Gauge Suggested Guide for Sighting Slopes for Safe Operation Warrantystatement Rev 4.27.01 JH/MH/JH/MH