Husqvarna GTH2250 owner manual Install Seat See Fig, To Attach Nose Roller See Fig

Page 7

ASSEMBLY

INSTALL SEAT (See Fig. 3)

Adjust seat before tightening adjustment knob.

•Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

•Pivot seat upward and remove from the cardboard packing. Remove the cardboard packing and discard.

•Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

•Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

•Pivot seat and pan forward and assemble adjustment knob and flat washer loosely. Do not tighten.

•Lower seat into operating position and sit on seat.

•Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

•Get off seat without moving its adjusted position.

•Raise seat and tighten adjustment knob securely.

SEAT

SEAT PAN

SHOULDER

BOLT

FLAT WASHER

ADJUSTMENT

KNOB

FIG. 3

NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate instruction below to remove the tractor from the skid.

TO ROLL TRACTOR OFF SKID (See Operation section, page 11, for location and function of controls)

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Release parking brake by depressing clutch/brake pedal.

•Place freewheel control in freewheeling position to disengage transmission (See “TO TRANSPORT” in the Operation section of this manual).

•

Roll tractor forward off skid.

7

TO DRIVE TRACTOR OFF SKID (See Opera- tion section, page 11, for location and func- tion of controls)

WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Be

sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other people and objects.

•Be sure all the above assembly steps have been completed.

•Check engine oil level and fill fuel tank with gasoline.

•Place freewheel control in "transmission engaged" po- sition.

•Sit on seat in operating position, depress clutch/brake pedal and set the parking brake.

•Place motion control lever in neutral (N) position.

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Start the engine. After engine has started, move throttle control to idle position.

•Release parking brake.

•Slowly move the motion control lever forward and slowly drive tractor off skid.

•Apply brake to stop tractor, set parking brake and place motion control lever in neutral position.

•Turn ignition key to "OFF" position.

Continue with the instructions that follow.

TO ATTACH NOSE ROLLER (See Fig. 4)

•Position brackets, washers and nose roller between deck mounting brackets as shown. Be sure to position brackets on correct side, as shown.

•Install hex bolts and locknuts as shown. Tighten hardware securely.

NOTE: Be sure tabs brackets are positioned in tab holes in deck brackets.

"B" BRACKET TAB

TAB

HOLE NOSE ROLLER

HEX

BOLT

LOCKNUT

"A"

WASHER

BRACKET TAB

 

FIG. 4

Page 6 Page 8
Image 7
Page 6 Page 8
Contents GTH2250 III. Children IV. ServiceGeneral Operation II. Slope OperationSafe Operation Practices for Ride-On Mowers Safety RulesTable of Contents Unassembled Parts To Remove Tractor from Carton AssemblyTools Required for Assembly HOW to SET UP Your TractorTo Attach Nose Roller See Fig Install Seat See FigCheck Brake System Check Tire PressureCheck Mower Levelness Check for Proper Position of ALL BeltsChecklist Operation Know Your Tractor HOW to USE Your Tractor Towing Carts and Other ATTACH- Ments To Operate Mower See FigTo Operate on Hills To Transport See FigsTo Start Engine See Fig Before Starting the EngineCheck Engine OIL Level See Fig ADD GasolinePurge Transmission Mowing TipsBefore Each USE Lubrication ChartCustomer Responsibilities General RecommendationsTractor Engine Spark Plugs CleaningEngine OIL Filter MufflerTo Remove Mower See Fig Service and AdjustmentsTo Level Mower Housing To Install MowerTo Replace Mower Drive Belt To Adjust Brake See Fig To Adjust Attachment Clutch See FigTo Replace Mower Blade Drive Belt See Fig Front Wheel TOE-IN Adjustment To Adjust Motion Control Lever See FigTransmission REMOVAL/REPLACEMENT To Adjust Steering Wheel AlignmentFront Wheel Camber To Start Engine with a Weak Battery See FigTo Remove Wheel for Repairs Interlocks and Relays To Replace Headlight BulbTo Replace Fuse To Adjust Choke Control See Fig To Adjust Throttle Control Cable See FigTo Adjust Carburetor Engine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsOFF Service Notes Tractor - Model NO. GTH2250A Schematic Electrical Tractor - Model NO. GTH2250AKEY Part Description Chassis and Enclosures 532177956 Ground Drive KEY Part NO. NO. Description Steering Assembly Adapter, Wheel Steering Spark Arrester KIT EngineSeat Assembly Wheels & Tires Decals532130171 Lift AssemblyMower Deck Wheel, Gauge Suggested Guide for Sighting Slopes for Safe Operation Warrantystatement Rev 4.27.01 JH/MH/JH/MH
Top Page Image Contents